Reviews
Not for everyone.
It is a hexagonal, low-head Profile Socket.
It is sold without any warning, but as a result of prioritizing handling, it is short and easy to use in some situations, but on the other hand, it cannot be used in places where Bolt needs a little length on the Socket side, such as a longer Penetrating Nut or Cap Nut. (Standard length sockets from other manufacturers or semi-deep sockets from ZEALBrand are required.)
Therefore, if you want to use one type of Socket for all parts of the system, it is not recommended at all.
For those who are willing to use low head whenever possible where sockets are used, and only replace them with semiDeep or other companies' products for exceptions after a bit. Beginners and Light users should buy something else. It is also not suitable for circuit use where you want to limit the number of tools you bring with you.
However, the rattling and bending when using Socket is close to Zero, so it is definitely reliable in usable areas.
View detail
Expensive! But if you don't buy this tool, you can't replace the Exhaust System!
[How is it used?
This tool is essential for removing the O2 Sensor of the Exhaust System.
I purchased this product when I exchanged it for YOSHIMURA's One piece.
Was the one you received as per Image?
Tools only, nothing else attached.
How was your experience with it?
Although I was concerned about whether Torque would really be applied, I was able to remove the Sensor without incident.
[Points to note]
CB1100's O2 Sensor is just too hard!
I was finally able to remove it while blowing CRC.
It may be tough with low-precision tools.
How did it compare to other products?
Quantity:There are inexpensive tools available as Set items, but I think this one is sufficient since it is only used for CB with only 17mmSocket.
The other tool is also available from Snap on, but is more expensive at over 10,000 yen, so we would like to have this one before it sells out.
View detail
Grip is easy to grip.
The grip with non-slip surface makes it easy to remove clips such as DoorLining, etc. Since it is a special tool for removing clips, it is convenient to remove the clips left on the panel without breaking. View detail
cooking Torx
This socket is very useful to open the torx nut and not to damage the nut head. It works well with ordinary vehicles. I would like to use it View detail
Structure is solid although it is an unaffected tool. Since it is fixed lightly every 90 degrees, the portion which attaches the Socket has good user-friendliness, and if a stick is inserted in the hole of the portion of a handle, it can be
Structure is solid although it is an unaffected tool.
Since it is fixed lightly every 90 degrees, the portion which attaches the
Socket has good
user-friendliness, and if a stick is inserted in the hole of the portion of a handle, it can be used also as a 600-mm long T character
Handle.
Probably,
special character exertion is a point which can carry out
of loosening the Screw which has become tight with high torque taking advantage of die length of 600 mm.
Since a Torque starts too much conversely as for bolting, careful cautions may be necessity.
View detail
If it is an object for M5, 3129-60-2 suits. Can it be said that whether the hole of designated size can open the so-called kind of a Bolt Extractor with a Drill at right angles to the Center of the Bolt which broke occupies 60% of a work succes
If it is an object for M5, 3129-60-2 suits.
Can it be said that whether the hole of designated size can open the so-called kind of a Bolt Extractor with a Drill at right angles to the Center of the Bolt which broke occupies 60% of a work success?
Moreover, when having adhered to, it is also important to dispel adhesion as much as possible to pervious antirust lubricant, such as ラスペネ, beforehand.
Generally, although a Bolt Extractor has many which are turned by a Tap handle, since this product is 3 / 8 angle Drive and it can be turned by the Ratchet or T Handle, its work is easy.
Once it bites, since the rest is what was closed when the reverse Tap part at the tip ate into the hole, and one side which bites, their beginning is important.
If
can be carried out, it will be a tool which I do not want to play an active part not much, but since various Sizes and the diameter Bolts of a large also have a product of 1 / 2 angle Drive, it can choose if needed.
View detail
It has the product of the old specification, and by the present specification, an axis becomes an ellipse, Round-and-round times become that an angle Drive part does not have less, and also when a Stopper moreover takes lessons from a center position and
It has the product of the old specification, and by the present specification, an axis becomes an ellipse, Round-and-round times become that an angle Drive part does not have less, and also when a Stopper moreover takes lessons from a center position and it uses as a T Handle, condition has become good.
For this reason, the product of the old specification would return to private life, will be struck, and will follow the second life as a stick.
At a Garage, it is NO as to whether if it then combines with an Extension bar, it is easy-to-use as an omnipotent Handle which becomes T Wrench and L Wrench.
That it is that which is good for the back is bad for the head generates that the die length of a Handle is fixation after all.
Therefore, when I fix at a Garage, a Sliding handle does not use.
If convinced to the above-mentioned restrictions, a Merit will come out as a portable tool of the two-wheel Touring which wants to reduce a property.
I am made to carry when running the Tool roll settled in a cylinder 200 mm in die length in the combination of this Handle, a Socket required for the Extension bar of two merits and demerits, and a Socket rail, and a Bit holder with a long distance and a friend.
View detail
When beginning to arrange a Hand Socket, what was purchased first was this Set. Although it was glad that it was with a Case those days, the Case has become unnecessary while keeping step with a Socket rail etc. before long at a Tool chest. This Case ha
When beginning to arrange a Hand Socket, what was purchased first was this Set.
Although it was glad that it was with a Case those days, the Case has become unnecessary while keeping step with a Socket rail etc. before long at a Tool chest.
This Case has become storage of the Socket which carried out two-team omission.
, of course, many of the ON groups are using the Socket itself in active service.
Although what frequency in use exhausted highly exchanges or has some which were lost, a Plating has not come off.
View detail
the tool of koken -- probably, there is in play [ no ] now. It is accuracy, user-friendliness, reliability, and a price that a tool is asked. It is perfect.
the tool of koken -- probably, there is in play [ no ] now.
It is accuracy, user-friendliness, reliability, and a price that a tool is asked.
It is perfect.
View detail
Since it is called koken, it is dramatically firm structure. They are easy-to-use goods that it is compact and easy to grasp.
Since it is called koken, it is dramatically firm structure.
They are easy-to-use goods that it is compact and easy to grasp.
View detail
If it is the components of a motorcycle, I will regard even the components which have become tight strongly however as the ability to loosen now. Since the die length is also 45 cm, it is ponderously heavy. So, cautions are required when fastening
If it is the components of a motorcycle, I will regard even the components which have become tight strongly however as the ability to loosen now.
Since the die length is also 45 cm, it is ponderously heavy.
So, cautions are required when fastening.
If it usually fastens and is crowded, any will stop, but since torque starts here, it fastens without limit and it continues being crowded.
It seems to be better to manage with a torque wrench so that it may not twist off.
View detail
If it uses for maintenance of a motorcycle, it will be recommended perfectly! Unlike maintenance of a car, by motorcycle with many open spaces, T type handle can be used in very many cases, If there is this, there is various merit ^^ It already turns
If it uses for maintenance of a motorcycle, it will be recommended perfectly! Unlike maintenance of a car, by motorcycle with many open spaces, T type handle can be used in very many cases,
If there is this, there is various merit ^^ It already turns and already loosens, once it tastes, I will think whether to become infatuation, and I regard a feeling of torque when it shuts by hand unlike a ratchet as whether there is almost anything twisting off a bolt by an overtorque sensitively.
First, although it is a function as a T type handle, remarkable work can be provided with this one, if the extension of favorite die length is given and the socket of 3/8 which probably has most frequency in use is inserted.
Of course, although I think whether it is best for there to be a wrench for every size,
I think whether this style is the best for the direction which avoids many places in neither work space nor the relation of storage (storage is possible space-saving [ which removes extension or becomes ])! Again,
Since a handle part can slide, find it useful very much to apply torque, and,
although I think that it is worried by some people (as three eighths of spinners -- the use possibility of --)
and since the handle is made to the ellipse in the direction which requires torque, I think whether remarkable high torque can be borne, while using it with the usual T type,
Since a handle shifts while carrying out the round and round time, since it is locked with a ball, it does not become precocious! Considering the above merit, I cannot regard substituting the top of a socket for a size as a demerit so much, either.
a feeling of quality -- it is an excellent piece which makes a mistake also in the thing and in which we can recommend it truly to you by Tokoro called made in Cau Ken that there is nothing ^^
View detail
When calling it the bit holder, the thing of bit maintenance with a magnet was most, but since he wanted to avoid magnetization of a bit, this product was used. Maintenance of the bit is just firmly carried out by the clearance considered to be the mi
When calling it the bit holder, the thing of bit maintenance with a magnet was most, but since he wanted to avoid magnetization of a bit, this product was used.
Maintenance of the bit is just firmly carried out by the clearance considered to be the minimum, without escaping simply.
I think that it is held by tension with a sufficient degree.
This price is very a recommend in this accuracy.
Since the combination by the side of three eighths of ratchets would be various, the star was set to four.
View detail