Reviews
US Buyers Read First
2016 Yamaha Zuma USDM. The part is very good. The fit and finish is fantastic and the install is pretty straight forward. BUT if youre in the US, this part will remove your OEM license plate light, so what you will need to do is cut the bottom oval of the black plastic tail light surround. The models outside the US have this precut, but we only have the outline. This will allow the tail light to serve as the license plate light. If you look at the description pictures on the listing, you'll notice the light hole. ALSO, the part is for plates somewhere outside the US therefore the license plate screw holes do not match up, you will need to re-drill two holes closer to the middle of the plates. I got the kit that ustilizes the OEM reflector, but shortly after install, I cut that bracket off for a reflector delete. View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Brake stopper
I really appreciate this feature in normal driving in town and in situations where the vehicle body is required to be fixed on hills, so much so that I wonder why it is not included as Standard Equipment in the Scooter. View detail
Fits: YAMAHA CYGNUS X (2-inch), YAMAHA CYGNUS X (3-inch), YAMAHA CYGNUS X (4-inch), YAMAHA CYGNUS X (5-inch), YAMAHA MAJESTYS (SE44J) (1YP), YAMAHA MAJESTYS (SE44J) (28S), YAMAHA MAJESTYS (SG28J), YAMAHA MAJESTYS (SEA5J), YAMAHA MAJESTYS (SED8J)
Isn't this nice?
Reasonable and affordable Image change is available.
The key cylinder is visible every time the engine is turned on, but I was concerned because the place where the key is inserted is a NORMAL color, like a …hmmm? The color of the key cylinder is like a skin color, and it is getting a little dirty, which was bothering me.
There are products that cover the entire surface, but I chose this one because it is cheaper and easier to apply. The color is Black, and I can't say for sure because I have my own preference for design, but I like it.
I am a little worried about the durability of the adhesive. I warmed it up a little with a fan heater and carefully degreased the key cylinder side before applying it.
View detail
The BB-SHOOT is a special sponge filter for BB-SHOOT.
Naturally, it can only be used with BB-SHOOT Air Cleaner. At first glance, it looks like free Sponge, so 1pc.1100 for one replacement (less than 1 to 2 months). I think that the price is too expensive, so I use a new Sponge and replace it at the time of 800 kg oil change, and wash the once-used Sponge with neutral detergent and dry it for a total of 2 times. The sponge used once is washed with neutral detergent and dried for a total of two times. I guess it would be better if I wash it more frequently because it gets dirty, but if I use more than 1000 kg of Sponge, I cannot remove the dirt and it remains on the Sponge. View detail
Fits: YAMAHA CYGNUS X (4-inch) EBJ-SEA5J, YAMAHA CYGNUS X FI (SE461), YAMAHA CYGNUS X FI (SE462), YAMAHA CYGNUS X (4-inch) SED8J, YAMAHA CYGNUS X (Model 4) SEA5J, YAMAHA CYGNUS X (4-inch) 2BJ-SED8J
Nice price, but the shape is good.
OEMFender to be removed and installed Type
Refreshing the best on the market.
All the back must be removed from the Seat to install it.
Large oddity.
By the way, there is no manual enclosed on how to remove it, so if you can't do it, pay the labor charge and have a PRO do it for you.
Reverse side is bare Wiring, but there is a Fender on the Tire, so it may be Large sturdy.
View detail
Fits: YAMAHA MT-09 (2BL-RN52J)
Your hips are Refreshing
When installing it, you missed the large size torque wrench and hurriedly installed the I went to buy one. (Lol)
And in the OEM Nut, when installing the Bracket to narrow the blinker spacing, the OEM Nut I couldn't tighten it up and tried my best to find a Penetrating style Nut.
The double-sided tape used to install the License Plate Light is It doesn't seem to come with it.
Looks nice, looks great Parenthesis.
It was just as good as I thought it would be.
View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Unfortunately, it's not attachable.
My PCX was not able to install Knuckle Visor because it is attached to my PCX. Because it is a simple part, installation is easy and the feeling of operation is also simple. I think it's not bad. View detail
It's not too bad, I guess
I was hoping to lock the Brake at a traffic light on an uphill climb or downhill By the way, the LEAD 100 I used to ride was Standard Equipment Being able to Brake Lock when loaded into the car also makes the Motorcycle more stable View detail
If you want to go Stylish, this is it!
Refreshing the Fender area of the CB250R
Fender Eliminator from 3Manufacturer as far as I know Kit is out, but I chose Adio's because it was the most Refreshing
There's nothing difficult to install, but this Kit allows you to install the license lamp You need to crimp the terminals yourself and you need Electric Works Pliers
It's very stylish and stylish as well because the long Fender is gone The only downside to this is that it's still pretty dirty
I only ride on perfectly sunny days, but even so, when I get off the Motorcycle, the Tail Not only the lamp, even the tandem seat is covered with small stains Parenthesis is good, so it's fine..
This product is a great recommendation for people who don't mind a little bit of dirt However, I can't recommend it to those who ride on a rainy day
View detail
It's changed!
I installed it on my LEAD 100
Two in the front fork, one in the rear suspension, and
I felt Front had changed with HaDrill
I've been picking up the fine Gap and getting through to the Handlebar
That's gone
Even Scooters are different, and I'm Big Li
By the way, I don't think there's enough Rear to experience it...
View detail
carburetorQuantity:Set has changed
I installed PWK28 on my LEAD 100 and this time I installed this product
LEAD is a long Manifold anyway
NORMAL, of course, because of the longevity of the mani that I one-off to my for PWK28
i installed 2 places in total on the carburetor side and the Lead Valve side
When it comes to the test drive, low speed, medium speed, it doesn't feel any different than before
The biggest change I felt was in the high speed range, the torque seemed to be thinner... (-_-;)
Looking at the plug, it looks like White
The air that was being pulled by the mani due to static electricity is gone, and the amount of air entering the Engine has increased Isn't it?
Now, let's see if we can't make an MJ exchange
I hope it turns out to be a good one!
View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Convenient to have
I remembered that it was attached to DIO and other OEMs, so I put it on
I think it's almost as convenient as you'd expect during a railroad crossing or a stop on a hill at a traffic light
However, I would like to see a long bolt included in the package if possible
And I wish I could lock it with my Left hand index finger, but Lever is too far away to reach it
It's a shame that I end up having to lock it with my Right hand while holding the Brake
View detail
Refreshingly, it makes you look better!
I worked from the information on the Net
Blinker's Spacer installation is the hardest part
Other than that, it wasn't difficult
As far as quality goes, the quality of the paint is a little poor and peels off easily during the process
What I'm interested in is the angle of the License Plate
That's pretty challenging
View detail
Fits: HONDA PCX125 JF84, HONDA PCX125 JF81, HONDA PCX HYBRID, HONDA PCX150
Installed on JF81 PCX
To install, remove the entire rear cowl and use the license It is necessary to cut the resin of the Plate Light section, so it is necessary to use the ultrasonic cutter and It is more beautiful if you have File etc
After the installation, New Model PCX has a thicker rear tire Rear view is parenthesis good without complaint
It's completely visual
However, I think it would be more upscale if the Number angle was more subdued
The bad thing is that the Seat lock section will be completely empty, so if you try to run it on a rainy day, you'll be able to get the Muddy water will get into the box In addition, sand will bite into the grease in the seat lock section
You need to make your own lid from the inner fender side
View detail
Fits: SUZUKI Address125 (2BJ-DT11A), SUZUKI Address125 (2BJ-DT11A)
For parking lock on the rear brake
You will need to remove the cowl around the Light as it is installed on the Scooter As there is no detailed information about this in the product manual, please refer to the service manual for further investigation is required
In my DT11A, the black cover part under Lever interfered with this product So I had to remove about 5mm
That took about two hours
I am satisfied with the function
View detail
Neatly organized around the rear
Installation is pretty Large weird If you have power tools "Cut" "Cut" I think you can save a large amount of time with the process of
If you can take the time, I think it's possible to use Saw and File etc. without power tools
Drilling is required for installation, so you need to have a drill
It takes a lot of time and effort, but you'll be thrilled when it's completed
Disassemble again by re-tightening the mounting screws when they come loose
I shudder to think of what I would do I wanted to have at least a screw loosening stopper included
View detail
Bolt is too suspicious
Before injection injection Bolt has used it
Even at over-the-counter sales, it is also a product that can be sold with confidence that it may be decided not to buy it after purchase by DIO
This time there are things that Reduce shipping fee is over 3,000 or more
I tried to buy it for Rear suspension
After all the ride feeling has improved somewhat.
Next time I will look at the opportunity and I will attach it to Front fork
View detail
Design and Size are good, but - - -
I got lost in L and M, but it was just good with M. but - - - Weak adhesion has come off from sharp corners. I am sorry I like ADIO's Logo. View detail
Perhaps it is good - - -
I tried dubious Parts
Fitted on Inolon's Bolt
I did not understand the effect clearly because I fought other together
I think I'm probably getting better
I thought that I could also make my own if welding could be done I lowered the evaluation slightly from the price
View detail
Angle is bad
I installed it because the OEMFender is running away.
Since machining is unnecessary on the car body side, installation is easy if you understand even how to remove OEM Fender.
After installation, Rear tire looked out from the back, the appearance improved..
However, the angle of Number is a bit too small, and I want to point it down about 5 degrees again.
(Actually, attention was paid to White bye) It may be good if you lowered Rear.
I ran about 8000 km, but there is no breakage or dropping out.
View detail