Reviews
I'm pretty happy with it
Installation is easy, though,
The tank cap hole is a bit large, so positioning is a bit difficult.
The texture is satisfactory.
View detail
Balance-wise, I think it's good.
First of all, Balance is not bad after installation.
By changing the angle of the meter, it is the gap increase Large and the scant feeling that depends on the thinness of the meter unit that I am concerned about.
I fill the gap with Lower cover etc. to solve this, but it is a certain company's manual processing product (OEM Product around ZEPHYR?). However, I gave up because it was too expensive to buy again.
In the first place, it is Image that a certain company made is the thing which imitates W3, but because the Meter attachment position of W800 is slightly low and backward, it was a little concerned with Image that the ear of Rabbit lay behind.
Once again, the coolness of the ZSeries Meter and Light unit is superb.
I installed it to try to pull in the Image around W1 with the Lower cover of Mr. Pleasure away from that line.
The positional relationship with the OEM Parts is not unreasonable and the balance is good.
It is recommended to replace Handlebar, Light unit, Meter Bracket, etc. in parallel.
It seems to be necessary to paint because it is FRP bare finish &Black Gel, then I think that the upper Rubber cover adhesive attachment was good in attachment, I feel that there is not much sense of incongruity even if I install it as it is, but if you are concerned about the surface whitening and deterioration of FRP, you should paint it lightly. I thought that it would be better.
If you want to match the texture with OEMMeter, you may have a hard time.
Because it is the goodness of the balance which fits naturally to W800, I think that it is good to be more like it, and there is an impression that it is a little W1 from a distance.
View detail
It is solidly made
I bought it for Circuit Running.
Rear axle shaft is easy to install because it is just pinching it.
When using Racing Stand, it seems better to pay attention to the position.
View detail
I'm glad I bought it.
I bought a Visor but I was not satisfied so much and I was looking for it, I found this and bought it. I was half confident, but I got really cool. However, the price was not satisfied for a moment. View detail
It does not repeat desorption.
It is for NINJA 2 Helmet 50SL, but it can also be installed on Z250SL.
However, in the case of Z "KAWASAKI" Since Logo is drawn on both sides of Tank, the last of Left Sidekawasaki "I" It hid, kawasak (Leather Sack) It will become. (Right barely "awasaki" It does not become. )
However, Z / NINJA It is common to note that the shapes are properly matched, so cover the gap and Tank / Repeatedly, Wank will definitely be added to Tank. Wound comes in handy.
I did not do it, but it may be avoidable if you slurp the inside or do something before installing and slippage.
After that, the other person is written, but those who lie down like riding over Tank will surely get in the way. If you pay attention only to that point, is it okay to install as long as you like it.
By the way, I have two objectives to replace Tank Pad and add Space for document entry.
It is written that Double - sided Tape is attached and used for installation, but I use it in the Dashboard such as a car from the purpose of putting in documents Pitat Seat? (Those who do not slide so that the thing they put on sticks) I cut it and used it.
View detail
Can also be used with ZX-14R
Since Base is made of FRP, it is easy to match the position.
The surface is somewhat soft, so it's a touch of preference.
In the attached Magic tape, because the gap opens, I fixed it firmly with a thick Double-sided Tape, but after all it opened.
In order to cover up to SIDE of Tank, I can avoid scratching with G bread etc and I will not go to Stomp Grip, but it is easy to hold as a nonslip.
If there was a little more height, it would have been better if Cover to near the fuel filler a little more ....
View detail
It is ! that what is necessary is just to improve adhesion with a Tank.
It is ! that what is necessary is just to improve adhesion with a Tank. View detail
Since ETC, the in-vehicle tool, and U character lock were carried under a sheet and there was no loading space in my Kawasaki ER-4n, this product was attached instead of the accessory case. Since a Tandem run was not carried out in my case, the
Since ETC, the in-vehicle tool, and U character lock were carried under a sheet and there was no loading space in my Kawasaki ER-4n, this product was attached instead of the accessory case.
Since a Tandem run was not carried out in my case, the effect of the Dress-up up was also aimed at and attached.
If this product is attached, it needed to push in from this product at the time of sheet insertion, and an edge face will crack.
Since it was a product made from
FRP, I had repair out of warranty carried out by a maker, but I think that there is no intensity not much.
It is unexpectedly found useful, storing a Net at the time of
, however a Touring, or storing rain gear.
Although
book product is sold as Ninja400R or an object for ER-6f, it is satisfactorily attached also to ER-4n!
View detail