Reviews
It's a shortcut.
[How is it used?
Used to replace oil in front fork of TZr250R.
I have changed fork oil several times, but it took me a long time to check the oil level each time, so I bought this to save time.
Was the one you received as per Image?
It was just like the picture.
How was your experience with it?
As is often the case with Yamaha vehicles, the amount of oil to be removed from the inner fork is quite large, since the oil is filled to the top of the inner fork once and then removed to the specified level.
This product is quite slow to suck up Speed. (Piston is heavy) So in that sense, it takes a little time.
However, the work time itself is reduced, so it is worth having one if you frequently perform maintenance.
The scale was also measured by Caliper and was generally correct.
[Points to note]
You should think of a way to secure Fork so that it does not fall over since both hands are occupied.
How did it compare to other products?
I have not used any other products, but I was not sure if I should go with the one-handed guy from DRC.
The DRC seems to have a lower usable oil surface height, so we chose this product just in case.
【Review】
There were no problems with the product itself, and it shortened my work time.
It is not absolutely necessary, so please consult with your Wallet.
View detail
Exhaust Spring removal!
[How is it used?
When changing oil, the drain bolt cannot be removed without removing the exhaust pipe of the exhaust system.
Was the one you received as per Image?
Yes
How was your experience with it?
It was very convenient. It was so good that I felt like a fool for having worked so hard with Radio pliers.
It is only a few hundred yen, so it is worth having if you often remove Spring.
It is useful both when putting it on and taking it off.
[Points to note]
None
How did it compare to other products?
Anyway, it's cheap!
View detail
Easy to use
We also used Adjuster, but it was not hard enough to turn very easily, so we decided to adjust it here.
It is Nutetc. friendly and easy to use with perfect accuracy.
View detail
It's the only way
I had another wire injector, but when I used it, the oil leaked out and it was no good at all. This one, however, did not leak any oil and did exactly what it was supposed to do. The price may be high, but this is the only way to go. View detail
I'm glad I bought it!
I had been trying to bleed the air out of my Motorcycle Brakes by making my own, but it didn't work well. I wasted a lot of time. I wish I had bought it earlier …. View detail
Fits: HONDA XR650 L, HONDA XR650 L, HONDA XR250 R, HONDA XR250 R, HONDA VT750 CD2, HONDA VT750 CD, HONDA VT750 C, HONDA VT750 C, HONDA VT750 C, HONDA VT600 CD, HONDA VT600 CD, HONDA VT600 C, HONDA VT600 C, HONDA FT500(82-83), HONDA GB500, HONDA NT650, HONDA NX650, HONDA RVT1000R, HONDA TL250(75-76), HONDA VF1000F(84)
VFR750F Flywheel removal!
Must-have item to remove the Flywheel due to StatorCoil failure! The puller itself looks like just a thick bolt, but the screw threads and texture are solid! It's a good time to be able to find tools like this quickly, as the number of old motorcycles increases and special tools are suddenly needed. View detail
Inexpensive and can be diverted for Brake maintenance
[How is it used?
I purchased this product for use on an old car during a front forkOverhaul.
Was the one you received as per Image?
For the price, Memory was listed and was of higher quality than expected.
How was your experience with it?
I used to maintain the system by diverting my own work, so it has become much easier to maintain.
[Points to note]
The attached Hose is a bit unreliable as it is a Material that seems to stiffen over time.Material:If you replace it with SiliconTube, no problem.
How did it compare to other products?
I have not used other companies' products, but I appreciate the fact that they are available in the $1,000 range.
▼The syringes have the same capacity as the Active ones normally used for Brake maintenance, so they can be diverted for Brake fluid replacement and air removal, although they must be cleaned, so they are a good value.
View detail
I feel like I've been cheated.
To be more precise, this tool can only be used to remove the Pulley side and to install the Clutch Side.
We don't use Rose's because it is Air, but we wanted to use it for Torque management when embedding...
I managed to fool them into thinking it was better than nothing.
View detail
Common Chain brush
The three-sided type from various manufacturers.
Brush. I used to use it before.
If the Cleaner bounces on the Wheel or
You have to do it twice or you have to worry about the order.
I can't wash my car and now I don't have enough Space for washing my car.
I use Tooth Brush because I can't do it.
I wash the whole car body at once and hose water.
I can use it! I think it would be very useful in situations where
The opposite is Straight's Brush, which I don't know how to use.
I didn't know what to do, so I stabbed it from under the Chain, and the gap hardened.
I used to use it to get dirt off of them, but as a result...
Seal was also hurt to shreds, so that's how I used it.
No recommendation…w
View detail
CRF100F (2007) Used in
Flywheel can be easily removed without any problem.
It is only a tool to remove Flywheel, so I wonder if it is cosmetic. Anyway, the Flywheel can be easily removed.
View detail
The best, but maybe not all-purpose.
Rumored Cable injector guy.
It is actually well thought out and much easier to use than the traditional Injector.
However, the size of the Cable's length adjustment nut is too large because it is made to enhance sealing. (about M8) In some cases, such as in the case of a Cable, the Injector may not be able to bite into the Cable's sheathing thanks to that section.
Also, sticking Wire× I could not penetrate the Grease with Wire grease with high viscosity.
Anyway, it seemed to work well with low viscosity GreaseorOil, and it is a much better tool than the existing Injector.
View detail
MINIMOTO Minimoto Tappet Adjustment Tool 3-Size Set
Fine-tuning of Valve clearance is more convenient than using ordinary tools
The accuracy of the tools is low and I would like to see the system a little more precise.
View detail
It can be used normally
Used for maintenance of Clutch Wire.
Parts cleaner, OilCleanerretc., and other smooth products can be used without any problem.
When I used Super Wire Grease from YAMALUBE, the grease was so thick that I could not use it properly.
View detail
Inverted Front ForkMaintenance Essentials
If the spring is just under the fork cap, I could manage to shrink the spring by force, but if there is a collar under the cap, it slips on the oil and there is nothing I can do. I think it is a necessity when replacing the oil of this type of Inverted Front Fork.:Once set and positioned, you can shrink it with a ratchet or similar tool to reach the point where you can safely disassemble it in a matter of seconds. View detail
Compatible with various Axle Shaft diameters
I purchased this product in order to disassemble the front fork of KATANA and remove the bottom case. View detail
Used to remove O2 Sensor from CT125CT110 HUNTER CUB
Used this one that fits Size for cleaning Sensor.
The ZETA Under Frame Kit is installed, but as it is, it interferes, so it needs to be shifted a little. (Just remove the footpeg side and you're good to go.)
Like the 110CUB, if there is a Connector on the Sensor head, a Deep socket or similar can be substituted, but without one on the CT125, there is no way to remove it, so I think it would be good to have.
View detail
Fork Oil Level Adjustment Kit
The accuracy of the syringe and piston is good and there are no air leaks, but the narrow hose requires a lot of force to pull the piston. Since it is impossible to pull the Piston with one hand, you can concentrate on your work by fixing the Gold Pipe on the Fork and making the Fork stand on its own.
Cleaning Hose and Gold Pipe for next time was also time-consuming.
It will take some time to work through the trial and error process, but once you get the hang of it, I think you will be able to proceed quickly and easily.
The Scale engraved on the Gold Pipe is also highly accurate, but it is in 5mm increments, so if it is exclusively for your car, marking it will help you to make progress next time.
View detail
It was subtle.
I was able to remove dirt from a large area, but the Brush included with Chain Cleaner was better at removing dirt in small areas and in the back. I thought the included Brush was smaller and easier to use.
In the end, we concluded that it would be quicker to use the included Brush from the beginning.
I think this area depends on the individual's cleaning style and personality (nervousness, etc.).
View detail
Great tool for cleaning chains
The chain of the motorcycle needs to be cleaned and oiled frequently, and it is quite expensive to go to the dealership to clean it, so I bought this unicar cleaning brush to clean the chain by myself. The brush head of this brush has a certain angle of inclination, and it is relatively easy to use , Nylon plastic products are also relatively strong and will not break. Special attention should be paid to cleaning the chain by yourself and not starting the engine, otherwise your fingers will be injured! -------------------------------------------------- -------- The motorcycle chain needs to be cleaned frequently, and it is very expensive to clean the bike dealers, so I bought this unicar cleaning brush to clean the chain. Nylon plastic products are also relatively strong and will not break. It should be noted that you must not start the engine by your own cleaning chain, otherwise your fingers will be injured! Powered by Google Translator View detail
Seal mounting is easier.
I am concerned about the durability of plastic, so I prefer DRC's Stainless Steel tool, but it has been out of stock for a long time. I would prefer to use DRC's Stainless Steel gloves, but they have been out of stock for a long time. It is inexpensive, so I can just give up and buy a new one if it breaks. View detail