Reviews
Fits: YAMAHA XJ650, YAMAHA XJ750, YAMAHA XJ650, YAMAHA XJ750
A-Top Carburetor Joint XJ650
It cannot be installed because it is facing the wrong way. View detail
Fits: SUZUKI GN125, SUZUKI GS125, SUZUKI GN125H
A defective product?
After breaking in, the engine was disassembled again and the valve hit the upper part of the piston, causing the EX valve to deform. I think it is a defect due to the forced structure and the position of the shaved part of the Piston that dodges the Valve is gapped, so it is better not to buy it. View detail
Fits: HONDA Rebel 250, HONDA Rebel300, HONDA Rebel300
a little too short
It was too short and when installed, the carburetor and air duct could not reach the Air filterBox. It could not be used. View detail
Disappointing quality
It broke down and the battery was damaged. View detail
It's not what it looks like in the picture.
The photo shows the Cable coming straight out from the Sensor, but the actual product is L-shaped. I am in a hurry so I will use it anyway, but I was deceived because I was looking for a straight product. View detail
Garbage
The lens is dirty looking with a lot of small pieces of garbage like chips on the inside of the lens, and the plating on the reflector is also covered with a lot of garbage.
With this level of quality, you will not regret purchasing OEM Parts, even if they are a little more expensive.
It was truly a cheap buy, and a bit of an expensive learning curve.
View detail
Fits: HONDA PCX125, HONDA PCX150, HONDA LEAD110 EX, SUZUKI ADDRESS V50, SUZUKI ADDRESS V50, SUZUKI ADDRESS V50 G, SUZUKI ADDRESS V50 G, SUZUKI LETS4 Basket, SUZUKI LETS5, SUZUKI LETS5G, HONDA SUPER CUB110
Don't buy it.
Installed on JA07 → flicker light for 5 seconds → then nothing → disconnection confirmed
[Don't buy it.
View detail
Fits: YAMAHA XMAX250, YAMAHA XMAX300, YAMAHA XMAX300, YAMAHA XMAX300
If you hear a strange noise when starting, watch out.
I installed it on my X max250 that I use for commuting and it has traveled about 700 km.
When I started the car, I heard a strange "goo”" noise, so I lowered the car and found that the Clutch Shoe was covered with wounds in places where it should normally be smooth and smooth.
It was the 38th day after purchase, but 30 days had passed since the product arrived and I could not discuss the problem.
Maybe you happened to run over HaGap, but it still recommends OEM Product.
View detail
Fits: HONDA PCX125, HONDA PCX150, HONDA LEAD110 EX, SUZUKI ADDRESS V50, SUZUKI ADDRESS V50, SUZUKI ADDRESS V50 G, SUZUKI ADDRESS V50 G, SUZUKI LETS4 Basket, SUZUKI LETS5, SUZUKI LETS5G, HONDA SUPER CUB110
50Meter
Running 50Meter and light bulb out. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z1000, KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z1000
Looks cool
I put it on, but it didn't fit, it felt like it was floating and I was worried about waking up the car body. The installation itself is easy. View detail
Installation itself was difficult; Shield gave up.
The installation itself is extremely difficult. The Image is a flat steel plate that is forcibly tightened to the originally curved front with screws. Even if I managed to install it, I gave up because the screw holes in the Shield do not fit and the load on the part is even greater, and it could be destroyed. I will return to OEM as soon as possible. View detail
I couldn't fit it on my Grom JC92.
Thank you for all your help.
Unfortunately, this time, the Size did not fit delicately and could not be installed.
It may be an individual difference in the product, but it is unfortunate.
Therefore, the rating must be the lowest.
View detail
nonconforming
Number of teeth on the OEM14-44, Initial Model of VTZ250 (87th model) However, the groove of the DriveSprocket seems to be slightly different and it does not fit and is unusable.
Probably VTZ250J (1988 and after) Note that the VTZ250Initial Model is also listed as compatible with the VTZ250.
View detail
not worth discussing at all
Although the total length of the wire itself is the same, the holder installation position (wire adjustment position) is completely different and cannot be installed.
The NC35 is included in the list of compatible vehicles, but it is completely useless.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z650, KAWASAKI Z800, KAWASAKI Z1000
It's not the same.
It's pricey, but it doesn't fit the size and it's rickety.
I can't even squeeze it with a hex screw. Can I sell this...
This is the worst product and you should not buy it.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z1000, KAWASAKI Z900RS, KAWASAKI Z900, KAWASAKI Z800, KAWASAKI Z650, KAWASAKI Z1000
They don't match.
I installed it on my 2021 Z900RS, and even though I tightened the screw as hard as I could, it still rattled and was obviously not a compatible product. The price is too high for a manufacturer that only deals with cheap Chinese products. The size of the hexagon is also mysterious and inconvenient. It is better not to buy it. View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA YZF-R3
No installation guide
Im very disappointed for this item. The materials box and appearance looks so cheap and not quality. Obviosly from china. Very expensive for this item. Wasting money. No installation guide and can not search on internet how to install it. View detail