Reviews
It's a small plastic board.
Even though it is necessary and unavoidable, I feel that 1,500 yen is too much, no matter how much it costs. View detail
Fits: KAWASAKI Ninja250, KAWASAKI Ninja250R, KAWASAKI Ninja250
problems that exist before they exist
First of all, the O-ring is too thick to fit.
You can't try to push or tap it in with Rubber Han and Prahan.
It's ha Gap among Active products.
View detail
So bad
Wire adjustment screw on handlebar side of 1 pc out of 2 is not tightened from the beginning.
When I tried to remove the protective cover of the middle wire adjustment, the Outer Crimp on the adjustment bracket fell out.
It's a shame because I have been using Active's High Solo for a long time on another motorcycle and I trust it.
View detail
This is no good.
It looks a little cheap, but it is acceptable!
I bought this product again because I had a problem with the Hazard switch after installing the first one and it was a hassle to return and exchange it!
I installed it again, no problem, and touring with peace of mind. The second time I pressed the Cell button, smoke came out of the switch box!
I had to cut and attach an OEMSwitch box and will never purchase again!
View detail
Fits: YAMAHA MT-09, YAMAHA YZF-R1M, YAMAHA YZF-R6, HONDA CBR1000RR, HONDA CBR600RR, HONDA HORNET600, YAMAHA FZ-6N, YAMAHA FZ6-S FAZER, YAMAHA FZ-8, YAMAHA FZ-8 FAZER8, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, HONDA CBR600RR, HONDA CBR1000RR
Clutch lever
Clutch lever, the picture and the Cinnamo's are different. View detail
Fits: YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA YZF-R25
Does not fit the former yzf-r25 with upright Fork.
Bolt of Caliper support interferes with OEMfloater.
It is not possible to cover the back of the Support with a washer as per the Support installation instructions.
The images in the Instruction Manual are also too small and white-black, which is the worst because it is hard to understand.
I will repurchase per Large person and OverRACING.
If you have been able to install it, or if you have the correct method, I would be grateful to know.
View detail
It doesn't stick…
The ActiveHP says it fits the 2022 XSR900, but in reality, it cannot be installed without machining. 2022 XSR900User, please be careful. The photo shows the machining done by a Motorcycle shop that has a milling machine. View detail
It didn't work.
I bought this Reverse Side for my CBR250R (MC41, 2011) at the same time as the pull/return, but this Reverse Side is different from the OEM and does not work.
The screw diameter on the Throttle side is so small that it is completely useless.
Why is this for a CBR250R (MC41)? I have no idea.
View detail
Fits: KAWASAKI Ninja250SL, KAWASAKI NINJA250, KAWASAKI NINJA250, KAWASAKI NINJA400
It doesn't stick as it is.
The product itself is good, but it does not stick as it is. The Sleeve is too thick, so I had to shave off the Holder. Please check the manufacturer carefully. View detail
Fits: YAMAHA YZF-R7, YAMAHA YZF-R1, YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-07, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, YAMAHA YZF-R1, YAMAHA YZF-R6, YAMAHA MT-09, YAMAHA TRACER900
TRACER900GT does not fit
Similar to the MT-10's review, the TRACER900GT cannot be installed as is due to interference with the lower part of the clutch holder. (I thought MT-09 series would be able to install it, but …) Please do not check for a good fit. View detail
It hits LeftSwitchCase.
Installed as per Instruction Manual.
NORMALLever can hold up to Grip.
This Active's Lever is a Switch's Case.
I adjusted the Wire and tried to run, but the Clutch runs fine, but ……………
When you grip the Lever, it hits the SwitchCase and makes a clack-clack sound.
It is likely to scratch the Case as well.
In the end, I returned to the original Lever.
I am not inclined to use it.
View detail
Fits: HONDA CB1000R, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA CBR1000RR
CBR1000RR SC77 2017 Lever is too close to the ground.
I replaced the NORMAL brake lever on my CBR1000RR SC77 2017, but after the replacement, the Touch hit the switch box even when the adjustment screw was tightened the most, which I did not like, so I went back to NORMAL. View detail
ActiveCore guard
The cooler and the Guard were matched to install it in the Oil cooler 13 step made by Active, but the Guard was small and the installation method as explained could not be done. I had no choice but to use a Tie Band to get it to fit. I am very disappointed with this product. View detail
cheap rubber plug over charged
it is different from the listing photo and webike won't take care They are just two cheap rubber plug over charged You can pick up easily from any hardware shore totally wasted money View detail
Fits: KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZR-7S, KAWASAKI ZR-7, KAWASAKI ZEPHYR400χ, KAWASAKI Z750, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, KAWASAKI GPZ1100
I got the wrong item
Described in the product description as Color black
Silver has arrived
unworthy of recognition
The system is inadequate
The same product has an S and B at the end of the item number, presumably the color number, and the product description says that both colors are It is listed as Black
I don't trust him at all
I want to see what's going on
View detail
Different sizes
I went out of my way to buy a 2mm thick product and all the ones I received were Thickness:It was 1mm
Why is this happening?
Very disappointing
View detail
LED not lit
I installed it and License Plate Light does not light, I know that I mail it to webike but leave it alone.
To inquire about Manufacturer
There is no contact now.
I should have bought another Manufacturer.
View detail
Before use but high price for the number of sheets. Expect for the effect after installation
Although it is still before installation, I bought it for measures against Oil leakage of Oil line. Although it looks like an ordinary Aluminum Washer, I think that Neck is expensive for a number. View detail
Fits: KAWASAKI Z1, KAWASAKI Z750FX-I, KAWASAKI Z1000MKII, KAWASAKI Z2
Big warning this is real shit!, i trow them away big waist of money. First it is real hard to get them to not leak. Second the tupe aroud them is lose and can not be back in place
Big warning this is real shit!, i trow them away big waist of money. First it is real hard to get them to not leak. Second the tupe aroud them is lose and can not be back in place View detail
It should be Bolt-on ,,,
To change to tmr this time I switched to high slot and switch type Small Type. I could do Wiring on my own by Universal, but I thought that dedicated Extra Processing Not Required was good as the time was good, so I made it to this product.
By saying that it corresponds to 95 - 96 years correspondence, my 1200 s was a 96 year model, so if I ordered without thinking anything, it was meant for gitf1200 of the Initial Model.
Type with Light OnOff switch.
I thought it would be wonderful if you had a description of the corresponding car model a bit more carefully. It's pretty pricey as well .... After all it's done Wiring.
By the way, the product itself is no problem.
View detail