Reviews
Easy to use as OEM compatible without distortion
Used on ZZr1100 (C1).
The OEM screen was damaged from the attachment point due to age-related deterioration, so MRA's screen was introduced this time for the purpose of repairing it. [Color] Clear? [Color] I was wondering if it was Smoke or not, but this time I decided to use it as a makeover. [Color] Smoke.
The OEMScreen is slightly thinner than the OEMScreen, but has less distortion than the OEMScreen, and has good visibility even when it is tucked into the cowl.
However, Smoke Screen is darker in color than I had imagined, and I think it would be tough to run face down with Smoke Shield's Helmet late at night.
A Screen RimRubber was also included and its length was appropriate and favorable.
I am glad to see that they are making parts that fit older motorcycles as well, as screens wear out due to scratches from flying rocks and need to be replaced periodically. Next time I will try Clear Screen.
View detail
For Japanese Vehicle Inspection Correspondence?
I had heard from my father, a Motorcycle shop owner, that if the Edge of the Screen is on the car, it will not pass inspection. [Color] I purchased Smoke and it came on Exactly with Zero gravity products by simply adjusting the length. View detail
The best Screen for Touring
The wind hits the shoulders and arms, but the wind hitting the body is reduced to Large width.
The movable Screen is good because the height of the Screen can be changed depending on the situation.
With the MovableScreen in the low position, the wind hits the lower side of the HelmetScreen.
When set high, the wind will be above the HelmetScreen at highway speeds.
With the standard Screen, driving was scary at speeds above 80 km/h, but the wind no longer causes fear even when driving at speeds above 100 km/h.
As for the NGPoint, there were some holes where it was difficult to insert the well nut because the diameter of the hole where the well nut is inserted in the blanket was uneven. In this hole, the well nut was inserted to some extent and then pulled out with a bolt.
View detail
Replaced from ZeroGra.
Installation is easy, even the well nut goes in easily if you are careful. No modification was required. However, it would be better to screw the tip of the nut to the cowl so that the gap between the nut and the cowl is small. The product is simply good and looks thicker and sturdier than the ZeroGlasses. Instead of that, the visibility [Color] The ZeroGlass cracked quite easily when impacted by a fall. I like the look and functionality of the ZeroGlass, but this time I decided to use the ZeroGlass! The fit with Cowl is not perfect, but I am satisfied with it. The wind protection effect is also naturally better than that of the NORMAL. I am glad to have bought this product. View detail
Consumables.
It is used for the sameManufacturer'sScreen.
I installed it for a car inspection and have been using it ever since because it looked surprisingly luxurious.
I bought it because after about 3 years, the Yellow tarnish became noticeable.
The lacing braid end bracket allows for a secure fit and has never come off at high speeds.
It is long enough to be used one more time, so I will keep it well.
View detail
High speed driving becomes very easy.
The only demerit is that the latest two-stage Screen compliant models are more than $10,000 cheaper
Other than that it's just Merit, HondaOEMScreen winds from shoulder to neck at 100 kilometers.
This two-stage Screen increases the speed range by 15 to 20 km/h, whereas the wind cutting sound can be heard in the airflow even when the screen is down.
The wind starts to blow from 120 km/h, but if you get down lightly, it is not hard even on the New Tokyo-Nagoya +10,
The best thing is that it's almost windless when it's down, yet down the road, if you fold it up, the wind comes to the Jacket just like the OEM.
View detail
During long touring!
The OEMScreen on the NC750X is too short, so I installed a supplemental screen, and although it doesn't look great, it works. I have not tried it at high speeds yet, but I am sure it will reduce fatigue on long tours. The airflow is felt to flow over the top of the helmet, depending on the angle. View detail
Fits: KAWASAKI ZRX400, KAWASAKI ZrX1200 DAEG (ZrX1200 DAEG), KAWASAKI ZRX1200R, KAWASAKI ZRX1100
Wouldn't it be cooler if it were a little longer than OEM...? For those who think...
I was thinking that an OEMScreen would look a little sad, but I bought it because it was the size screen that Long had been looking for.
Installation is very easy, just remove and replace the screws!
When I actually installed it, I was glad I had purchased it because it was exactly the shape and length I had imagined and liked!
Please note that I honestly don't think you should expect anything in terms of wind pressure (lol).
View detail
Thin scuff marks are ....
The 25R is equipped with Smoke Screen by Magical racing, but the 4RR is Clear because it is a track day Main.
The large holes for well nuts and other mounting bolt holes fit EXACTLY with the OEM. With a bad product, the bolt may be forced into the slant, etc., but there is no problem with MRA's screen! The only regret is that there was a thin scuff on the inside running horizontally! The packaging is carefully done.
Maybe it got on during transport? The blindfold treatment on the tip has been done for a long time. It's a very professional item.
View detail
for Race.
Purchased to meet Race regulations.
It can be cut to the required length with scissors for installation.
It may be roughly twice as long.
View detail
Summer Shield
The OEM Shield is excellent and windproof, but I bought the Small Type Shield because it gets too hot in the summer.
The OEM Product is about between the nose and eyes at the lowest position, and wind protection up to the shoulders on the sides, but this product is about 12cm shorter, so the wind comes up to the upper chest and armpit area.
The instruction manual is in German, English, etc., but it would have been very easy to attach the washer if I knew how to use the long screw on the bottom side to stop the washer with the Rubber O-ring. The molding on the edge would float in the recess at the top, so I put the included Clip on this part to stop it from coming off. I had a hard time because the braid was hard, but if you soften it with hot water, it is easy to put it on.
View detail
Be careful in case of rain.
Raindrops roll in around the Meter at speeds exceeding 150 km/h (mystery)...
However, when a crosswind came, the handlebar had been taken away, but this was not the case this time.
View detail
Excellent replacement screen
Since the oem screens are no longer available this was my next choice. Excellent fit, mounting holes lined up perfectly. The only issue is the trim piece they supply is horrible. Clear trim that you are supposed to secure onto the screen with metal clips. I bought black rubber trim on Amazon and cut it to length. View detail
highly effective
I decided to buy it after experiencing the pain at high speeds, and it would have been even better if the design had been a little snappier. The design could have been a little more sharp, especially the bottom edge near the headlight.
The effect of the installation was outstanding, and the fear of the body being stripped by wind pressure was gone.
View detail
Windproof effect is possible.
I wish the design was a little more attention to detail, but it works great, so that's good. Overall, it is a good product. View detail
Fits: YAMAHA Tricity155, YAMAHA TRICITY125 (BirdCity125), YAMAHA TRICITY155 (BirdCity155)
I wouldn't say it's an Extremely Large, but it's not bad.
I happened to find Screen Touring for BirdCity in stock, so I bought it and installed the gradation type in Smoked color on the Initial Model BirdCity125.
Bolt longer than the OEM bolt supplied with the product is used to raise the mounting position. NeoPlane Washer. Spacer of Sponge rubber called "Spacer" is inserted between the Bracket and the Screen.
Instruction Manual with 8mm height is Quantity:2pc. Set, 10mm is Quantity:2pc. It says that the set comes with different mounting holes at the top and bottom, but the one I received contained 1 pc. of 8mm and 3 pcs. of 10mm.
If it is too long, just shorten it, but I don't think it matters much because where there is a 2mm difference, the actual item looks like it is only a 1mm error, and in the end it will be crushed when the Bolt is tightened during installation.
The attached molding to the screen edge was not installed because the molding itself was hard and positioning it was troublesome.
Screen's [Color] Smoke, but you can see the road surface in front of the vehicle through the Screen.
In BirdCity's Riding position, there is no problem to choose Black if you are a Scooter, because you will not see through the Screen with your body face down.
The OEMScreen felt like it was snugly attached to the cowl, but with the use of the above mentioned Spacer, it was mounted to create a gap, and it seemed as if a draft might get in while driving, but this was not the case.
However, it is not longer than other external screens, so the windproof range is from the neck down.
I wear a full face helmet, but right after the Screen was installed, I felt the wind only under my chin and thought that the OEMScreen was just a Meter visor.
The rest interfered with the previously installed Hand guard.
Even with interference, Screen's Quantities:Pair (for Left and Right) The handlebar is thin only at the part where the handlebar is cut, and the hand guard itself is soft, so the handlebar can be cut into a quantity.:Pair (for Left and Right) It does not interfere with driving as the Guard only deflects slightly when turned fully off.
I think the other brand product of BirdCity that does not seem to interfere with the hand guard is this Screen or Asahi Windshield, but if I had to choose by design, it would be this one.
View detail
Screen Mounting
Since it is black, it is naturally invisible when face down.
It is a little confusing because it is not a detailed instruction manual, but I was able to install it successfully.
I thought the with Rubber Nut on the OEM was easy to put on when new.
I applied silicon spray to the rubber part and screwed it in, but it may not be possible due to deterioration of the rubber, so it is recommended to prepare OEM in advance.
View detail
OEMScreen was damaged.
I installed this on my 2012 CBR1000RR.
Small scratches on the OEMScreen were becoming noticeable and were replaced.
I think the shape is almost the same as OEM. [Color] Compared to the Smoke-sensitive OEM, this product [Color] The clear design allows for better visibility and recommendation. The installation is also an insertion type, which makes it easier to replace than OEM.
View detail
Effective
I installed MRAShield on my SV650 to reduce wind pressure at high speeds, but there was a swirling airflow around the throat area, so I added eXcreen. The airflow around the throat was raised up to the eyebrow area, so it became more comfortable. View detail
After wavering with the zero gravity, it carried out here. the ease also of being also qualitative -- it was good that it was right [ that ] (self-delusion) and with [ corresponding to an automobile inspection ] the marginal rubber. 3 mm in thickn
After wavering with the zero gravity, it carried out here.
the ease also of being also qualitative -- it was good that it was right [ that ] (self-delusion) and with [ corresponding to an automobile inspection ] the marginal rubber.
3 mm in thickness is strong and it is actually good.
About attachment, it was easy.
However, if compared pure, there is a gap a little.
I think that it is a level to worry.
Although a smoked type order was placed this time, since the bottom 1/3 is dark smoke, the inside of a cowl cannot be easy to be seen.
If the hole (air duct ?) is merely open in this dark smoke subordinate part and rain, garbage, etc. enter Is it meaningful although he thinks that it does not enter privately?.
I think that something will close.
To the actual run, it became quite easy by ICHIMARUMARU kg~ICHIROKUROKU kg on the highway as which the protection-against-wind effect is not felt especially in running a public road with legal speed at the time of a run (various any more, since I was fearful, it was not able to take out).
However, it was worrisome that he gets the jitters and sound can be heard with BIBIBIBIBIBI.
If it gets used, there seems to be no problem.
Appearance also becomes smart synthetically and I think whether to be the better one since the physical feeling at the time of high speed operation was also made.
(I would like to have come to compare with ZEROGURA)
View detail