Reviews
Chain cleaning essentials
[How is it used?
Used to clean Chain every 500 km.
Chain cleaner is sprayed on and then shakily scrubbed.
Was the one you received as per Image?
As per image.
If they cost more than 1,000 yen each, a little more BALIetc. surface treatment would be nice, but it does not affect the performance.
How was your experience with it?
The size is just right for MotorcycleChain, and the back and underside of the chain can be easily cleaned.
[Points to note]
Spraying and scrubbing with the Cleaner will clean the Plate surface of the Chain and feel good, but it is important to use a Large amount of force to avoid damaging the Seal Ring more than necessary.
How did it compare to other products?
I think DAYTONA and others are almost the same in shape and performance, but the Brush part seems to be interchangeable.
Other items that would be helpful
Items to buy together
・Maintenance Stand
・Chain cleaner
・Chain lube
・Dustcloth
Rubber gloves etc.
I think Chain maintenance can be done anyway if there is a
View detail
At first, I didn't know what to expect...
When I first got it, I wondered how I could measure it, since there was no translation (please enter here Instruction Manualetc.) and I had to rely on pictures and so on. I wondered how to measure it.
After doing it a few times, I figured out how to do it, and once I understood it, I found it to be a useful tool.
First, 0Start is determined, and then the Chain's amplitude (slack) is measured, but there is a procedure, so it may be difficult to understand even if it is explained in the Instruction Manual... (Translation (please type here, if there is a video or something like that, it is 0))
View detail
It's easier to work with, but...
Found from WeBig's imprint.
I wanted to see it used myself and bought it lol.
I used it right away.
Certainly, the grease leaks less than the one I used to use. However, the grease spray inlet is too small to fit the grease spray that I have, and it leaked from there.
I wonder if it would be easier to use if I could devise a little more.
View detail
The Wire lube injector lives up to its reputation.
[How is it used?
Used for refueling Wire
Was the one you received as per Image?
Yes
How was your experience with it?
The lubricant reached the tip of Wire better than I had imagined.
[Points to note]
Note the direction of the wire's leak-proof rubber.
How did it compare to other products?
The unit price is high! But after using it, I am convinced. I don't think I will ever use Injector again!
Other items that would be helpful
Opinions and requests to Manufacturer I would like to see the rubber parts issued as Repair Parts, as their lifespan is unknown.
View detail
Best, but not omnipotent.
I became interested in it through a feature article on webike and bought it.
It is significantly better than the common Aluminum Injector, but not completely problem-free.
First of all, it takes time to put it on. The Packing is put through the Cable and the Body is tightened, but the amount of tightening is large and must be turned many times.
When the body is full, the remaining oil leaks out from the slide portion when the body is removed, so curing and dustcloth preparation are essential.
Naturally, it cannot be used with the Cable with Throttle's Guide (the same applies to the conventional product).
I am concerned about the durability of the spiral Cut Packing as it is a special shape and not sold individually.
However, there is nothing better than this in terms of oil feed capacity, and since pressure can be applied at the slide, even hardened old oil can be pushed out at once.
View detail
It can also be used for car washing.
One thing that always accompanies an off-road motorcycle is, after all, washing the car. It would be nice if we could use the car wash machine at Course to wash the car immediately after riding, but that is not always possible.
It would be nice if you could wash the car right away, but if you leave the car for a while, the mud will harden and make the car wash even more Large strange. Therefore, it is recommended to wash the car at the timing when the mud is still dry after driving, so that the mud can be easily removed.
It can also be used with the Moto Spade in one hand while scraping mud out of the car wash. The Brush part is especially easy to use when washing the car.
It is a well thought-out form and easy to use, as only the Brand "Motion pro" can do.
The only drawback is that it is a bit expensive.
I try to carry it with me by shoving it in my car's Off supplies box.
View detail
Thank God!
I used to use a Wire injector of the type often sold at supply stores, but I couldn't get it to refuel properly, so I bought this one.
I was a little bit worried about the wire injector, but it turned out to be the right decision.
I used Bell Hammer for the Oil and was pleased with how well it penetrated from entrance to exit.
View detail
You can throw away all the other W's except this one.
[How is it used?
The number of large motor cycles with cable-type clutches has increased to two, and although we had a conventional wire injector, it was no longer useful and was left unattended.
I was thinking it was time to clean and lubricate Cable and then I saw the Webike introduction article.
I thought, "This is it! I thought, "This is it! It took more than a month for delivery, but I finally received it the other day and tried to use it right away.
Was the one you received as per Image?
It was bigger than I expected. w The length is about as long as a box of Cigarette.
It seems to be a California-based manufacturer, and although it was manufactured in China, I think the quality is not bad.
How was your experience with it?
Compared to the conventional type of wire injector, Quantity:It takes time and effort to Set.
The procedure is
Turn the body and separate it into two pieces→Pass the Cable through→Attach the black rubber part by wrapping it around the Cable→Screw the separated Body→Lubricate it
I had to shave the tip of the tube to make it thinner, but it is better than too thick because it can cause leakage.
Quantity:Set is time-consuming, but it is possible to properly set theQuantity:If you set the wire injector, it will not leak all over the place and not enter the Cable at all, as is the case with conventional wire injectors.
Every drop of the blow is injected into the Cable and blown out from the other side, which is Large strange and pleasant.
Stress-free.
[Points to note]
Quantity of Rubber parts inside:If the set-up is not properly done, it will leak. Since the structure is sealed at three points including the O-ring and other rubber parts, it will leak if it hardens over time.
There is some concern about durability in that area.
How did it compare to other products?
It is incomparable to conventional wire injectors in terms of leak-free and reliable lubrication.
Exactly Throw away everything but this." W
It is expensive, so it depends on how long you can use it, but I think you will be happier buying this rather than getting frustrated with Gold for a tool you can't use.
View detail
Better than ever!
[How is it used?
I used it to make the clutch a little lighter and to prevent the wire from rusting, since the clutch yawer was replaced.
Was the one you received as per Image?
I'm using it for the first time. YouTube." I tried it after watching the video at
How was your experience with it?
Installation was easy and lubrication came out the other side of the Wire with no leaks.
[Points to note]
Be careful of the direction of the rubber packing that fits into the wire, and press the top part at the end to drain out any remaining lubricant inside.
It is
How did it compare to other products?
The Injector I used to use leaked lubricant from the entrance even when the screw was tightened, and only about half of the lubricant flowed out.
It was like they were not coming.
I don't think I will ever use the old Injector again.
View detail
Seal mounting is easier.
I am concerned about the durability of plastic, so I prefer DRC's Stainless Steel tool, but it has been out of stock for a long time. I would prefer to use DRC's Stainless Steel gloves, but they have been out of stock for a long time. It is inexpensive, so I can just give up and buy a new one if it breaks. View detail
Made of high quality Stainless steel!
It is easy to use because it is expensive and the Tray section is thick and quite stable (heavy in weight).
Stainless steel is good… expensive but lol.
The Week Point is that the Magnet on the back of the Tray came off (fixed with glue) … It's expensive, so please make it more durable lol.
View detail
Love this tool!!!
When I re-grease the linkage on the rear suspension there's one nut (connecting arm to frame nut) that I can't get a torque wrench on because there's not enough room. So I've been tightening it without the torque wrench wondering if it's too tight or not tight enough. Didn't want to spend the $ for one nut. Finally after several grease jobs and worrying about that nut I decided to buy the adaptor. The instructions were easy to follow. I was able to use the adaptor at a 90 degree angle to the torque wrench so I didn't have to recalculate the torque. The tool works awesome and I tested it to some other nuts that are accessible with the torque wrench alone. Spot on! I basically bought the tool for one nut but I'm glad I did. I am a wrench head and love to work on my bike and want it.done right. To me it's worth it for the peace of mind. Nice addition to the tool box!! View detail
Love this for my bikes plugs!
I haven't bought a gap tools for over years. Turns out mine were all too big. This fills the bill being light and easy to use.Handy tool to have in your moto box. Well made, durable, works as it should, and looks cool as well! No complaints here.I use it more to open a nice cold adult beverage than i do for gapping spark plugs, but it works great for both! View detail
Great little coolant recovery system that was easy to install.
2 week standard shipping was nice turnaround, and it definitely was less expensive than the other tank carried by this vendor. It was a little difficult to find a suitable mounting location on my Honda CRF450 but it was worth the effort just for the peace of mind knowing the radiators always are full of coolant. The coolant reservoir is well made and was easy to mount and plumb. It came with everything needed but I used better zip ties. The size is easy enough to fit many places. So long as I can see coolant in the overflow tank I know I am good to go. Even if it gets a little too hot while sitting still it sucks the coolant back in when run start moving again and it cools a bit. There is good reason that all street bikes and all autos have these. View detail
cheap and good
Replaced old grips on an Crf250 with these. My son liked the feel. Basic cheap grips that get the job done. Why pay more?They are not super soft but not rock hard and fit great.The grips did last but he end did blow out after he laid the bike down on the asphalt. No harm to the actual grip, just the end cap. View detail
Useful but not necessary?
Pretty simple tool for more piece of mind when doing chain adjustments. Works well on my bikes. I put the tool on just to see if my current alignment was good. It is, but the tool confirmed my suspicion that the alignment marks on my swing arm are not stamped symmetrically. I eyeballed it prior to purchasing this tool. If you have calibrated eyesight, an alignment tool isn?t really necessary. But, this is an affordable and useful little device to make the job a tad easier. If you have deep pockets, I imagine the laser alignment tools would be the way to go.When done, rear wheel spun more freely and with less noise. Simple and quick to use! View detail
Perfect tool for the job!
I was a little skeptical about this tool working as promised, but I'm happy to say it got the job done pretty well. ther than the fact that you need both tools, it was worth it for me because I have multiple bikesDefinitely recommend to have for steering stem bearing removal and installation!! Makes a dreaded job so simple. Takes longer to set up tool than to get the bearing off. No cutting, no beating. Pulls bearing off with NO damage to stem or clampsWish they were not as expensive as they are since it's such a specific application but it really does work like a charm. View detail
I diverted it to Car.
I diverted it to Car. CHARGE cooler (Water-cooled intercooler) The vehicle does not come standard with a reserver tank for the radiator tank, and the overflow is discharged to the outside. Now I don't have to bother to open the radiator cap to refill the tank with coolant.
I had no hesitation in ordering from WeBig, a trusted Motorcycle supplier.
View detail
You can throw away everything but this.
The price seems high, but I have been using Quantity:I was using that hard-to-use example guy for about 5pcs.
I threw them all out a few years ago, but for some reason I bought them on Astro this past February, and when I used them, … yahari… they're so hard to use!
If the fixture is a Quantity:2pc. I bought the one with the Set and was expecting a little more, but…
I have purchased and used this one and my impression is as others have stated in the Title. [You can throw away everything but this. is one of the choices! is
I just purchased it from Astro and would like to give it to a friend. w
View detail
It is a good Brush.
It washes Chain well.
You can wash the Tire by simply turning it by hand to scrub it.
It would last about two years.
View detail