Reviews
exquisite
Exquisite presence.
Cheap, for better or worse.
View detail
Pricey but sturdy
I bought this because I had trouble with the Hand guard or tipping it over and spinning it. I have tipped over many times and so far no problems at all.
The screws do not come with the product, so you have to prepare them by yourself. zeta comes with screws, so if you have trouble, you might want to go for that.
View detail
It doesn't turn more than ACERBIS.
I borrowed it from a friend and used it for a riverbed Course run and WEX East Gaia 90min April 14, 2022 Large meeting.
The vehicle model installed is a 2021 YZ250FX.
Handlebar is changed to Zita's SUPER LOW Quantity:Pair (for Left and Right) are cut by 5mm each.
The OEM bar pad was cut and installed.
The four bolt clamps seem to be working well, and the area near the handlebar end seems to be less prone to distortion.
View detail
This is for the Taper Bar.
This is the only one I have for the Taper Bar. As for the other products, the bite of Clamp and Handlebar is not good. Because this can bite in the straight part of Handlebar, it can fix it tightly. If the guard turns, it will lead to damage of Master Cylinder or Brake hose in the worst case. The only drawback is the Bar pad. The only drawback is the bar pad. The only drawback is the bar pad. View detail
When you Gap, you Gap.
I've been using this one for 6 months now as it seemed more sturdy than Zita's.
First of all, it's certainly more robust than Zita's, and it can be securely attached to the Handlebar.
But depending on how you fall, it's surprisingly easy to Gap.
Regular re-tightening will prevent a little, but when you Gap, you Gap.
It protects your hands from the branches and standing trees of Woods, etc., and you can put it back in your hand even if it's a little gap. This is a good product to use while using it. This is a good product to use while using it.
View detail
TouringSEROW'Installed on a '18
Anyway, it's Firmly made
There are three connection points to choose from to connect to the Clamp, so most motorcycles can be used with it Grip end part is for Aluminum Bar and Anchor for Steel Bar I'm using the YAMAHA OEM Grip heater, so it's included I used the OEM cone expander instead of using Anchor The end part of the end of the cone expander is nicer
It took me about 3 hours to change from the TwoSEROW hand guard It takes time to make subtle adjustments:Pair (for Left and Right) It wasn't the same subtly, but I guess it's within the margin of error There was no interference with Hose and Cable that I was worried about
View detail
I was never a Hand guard
On the Net "The strongest Hand guard is the CYCRA, FA I had seen a few posts about this, so I installed it when I bought a new car
But it was easily deformed by the first fall, and where's the strongest? I thought …
I tried to fix it by fixing it with Vise and bending it, and it didn't freak out when I put all my strength and all my weight on it
I knew he was the best. I was wrong
No more hesitation:I bought one more set
No complaints about the accuracy and quality of the workpiece
I didn't find it as messy as others have suggested
View detail
Pretty good
Both texture colors are quite high quality.
Large I'm strange.
However, when it is seen from the top it is a real squid. And the leading CYCRA Decal was not attached.
Regarding the installation, it is finished by drilling and opening the four places with the hole.
View detail
It is necessary to install it, but the strength is the best
Devices to install PlasticBumper are necessary. Hole positions do not match as it is.
The included Screws rust soon.
Although it overturned several times violently after installation, there is no deformation, no rotation.
Although it is somewhat expensive, you can recommend it for people who place importance on strength.
View detail
Paste on the Sticker got a bit nuanced..
Mounting on KTM 690SMC-R.
Buy Taper type for Taper Handlebar.
The installation itself is relatively easy if there is a Maintenance tool.
Although it must be installed to avoid Brake and Clutch hose,
As a mounting position is generally good.
Because it does not fit exactly for Other Company Product,
There is a need to firmly fix it.
To mention the inadequacies, the pasting of the Stickers was slightly gapped and felt sloppy.
Once peeled off and pasted again, only there is a little disappointing.
Just about appearance and performance can be recommended Recommendation!
View detail
Fits: YAMAHA YZ125, YAMAHA YZF250, YAMAHA YZ250 08-14, YAMAHA YZF450 08-13, YAMAHA YZ250 08-14, YAMAHA YZF450 08-13
Cospa best
It is in use to YZ250.
Unlike other company 's Disk guard, we do not need Adapter, so we can protect Reasonable Front Disc.
The difficulty is that it is made for Large texture, so if you put it somewhat, it will be Mosari.
However, having been built in Large size means that the new disc can also be used for vehicles that have become Large type .... maybe….
Well, if you can Guard with half the price of other companies, I think that it is a cheap product.
View detail
Retention power is excellent
Stealth's Clamp used before was easier to loose, but after changing to CYCRA this time it fell more than 10 times but there are few loosening slacks. Processing details are also polite and Large strange. View detail
Fits: HONDA CRF250 R, HONDA CRF450 R 09-12, HONDA CRF450 R 09-12
I used it for XR 600.
I used it for XR 600.
I stop with the Tie Wrap from the bottom of the Triple tree, but because it is Mask for the inverted, it does not match the diameter of the erect Inner Tube and it bite the Sponge. To fix the upper part, cut out the Aluminum plate and extend the Bracket from the Top Bridge to fix it.
Although the part wrapped around the Bar pad is extended, it may be not going to work if you try to fix it depending on it slightly short.
Parenthesis is preeminent to install, so if you try to divert it to other cars please do your best at ingenuity.
View detail
Fits: YAMAHA YZ125, YAMAHA YZF250, YAMAHA YZF450 06-09, YAMAHA YZ250 06-09, YAMAHA YZF450 06-09, YAMAHA YZ250 06-09
Cool
I bought to remove the Number and Headlight of WR 250 R at Course, because Meter's Bracket never got removed, I fixed it up and down with Tie Wrap as it was without changing its position, although I went out a while ago but it became like YZ Cool, because Headlight and Number are fixed with removable Tie Wrap, public road can run if it is 2-3 minutes.
View detail
Fits: YAMAHA YZF250, YAMAHA YZF450 14-16, YAMAHA YZF450 14-16
I mounted it to my YZ250f 2014 year model.I couldn't make up my mind which one to chose because so many skid plates are offered by so many manufacturers. But decided to chose this one because I was attracted to the plastic material. The pl
I mounted it to my YZ250f 2014 year model.
I couldn't make up my mind which one to chose because so many skid plates are offered by so many manufacturers. But decided to chose this one because I was attracted to the plastic material.
The plastic makes it light.
Mounting is easy as well. You only have to screw it on at two sections.
When mounting there is space between the bracket (included in the package) and plate. So be careful when you're tightening the screw.
Due to the soft material of the plate, you must be careful not to tighten it too much.
View detail
In a MOTARD, it is Good by the Compact size and a simple Design! Since a little Sticker had shifted, it was re-covered.A little processing of a hole is also necessity.
In a MOTARD, it is Good by the Compact size and a simple Design! Since a little Sticker had shifted, it was re-covered.A little processing of a hole is also necessity. View detail
If it attaches to WR250 X/R, since it interferes variously, we will recommend you the purchase of the Replace Side mount of ZETA, and a Pro-bend simple substance.Since working accuracy is quite coarse, if it attaches by itself, those who can corr
If it attaches to WR250 X/R, since it interferes variously, we will recommend you the purchase of the Replace Side mount of ZETA, and a Pro-bend simple substance.Since
working accuracy is quite coarse, if it attaches by itself, those who can correct many things will think that they are good.
Although
and the Shield fitting hole which is not attached unless it pushes in with a Screw, becoming hot were not used for a target as a result of [ a place is a little / right-and-left / different from ]
, either, the Bolt holes of a Side mount of the thing which I attached are [
and a Bumper ] American Qualities, such as slant
, a little.
View detail
It purchased in order to attach to a Motocross Motorcycle. First, structure of goods is solid and it can attach in comfort.form being also good and carrying out it -- also becoming -- it is very pleasing.Although the price is an ordinary price
It purchased in order to attach to a Motocross Motorcycle.
First, structure of goods is solid and it can attach in comfort.
form being also good and carrying out it -- also becoming -- it is very pleasing.Although the
price is an ordinary price, a Total balance thinks that it is very high parts by the material feeling which is used for a long time.
The
Handle became somewhat light and satisfied, after changing into this, since the Frame type made from an Aluminum was used until now.
View detail
[Webike Monitor] SL230 is equipped. Although attachment was completed satisfactorily, a part for the thickness of the Clamp attached to a Top bridge and four long Bolts are needed separately. the guard body and the Clamp are firm s
[Webike Monitor]
SL230 is equipped.
Although
attachment was completed satisfactorily, a part for the thickness of the
Clamp attached to a Top bridge and four long Bolts are needed separately.
the
guard body and the Clamp are firm structure --
-- the doubtful overseas thing which often exists is a great difference.
It is satisfactorily fixable also to a pure Renthal Handle, and although it falls over just for a moment, remain unmoved.
Recommendation
Although the
price is slightly higher, also make it those who appear in an Enduro race as well as
path-through-a-wood run.
View detail
Since it attaches firmly only by puncturing so highly [ a price ], I think that it is good. Since it does not change so that the color is also conspicuous with a Kawasaki green, appearance also becomes a Sharp and I regard it as good.
Since it attaches firmly only by puncturing so highly [ a price ], I think that it is good.
Since it does not change so that the
color is also conspicuous with a Kawasaki green, appearance also becomes a Sharp and I regard it as good.
View detail