Reviews
I like the tuning fork Mark.
I bought it because I like the design. I expect it to be durable.
The curved tank at the bottom was attached by pushing it down. I think it is better to stick it carefully here.
I'm a tedious person, so I do it in one shot, but the original procedure is (1) Centers. (2) Spray an appropriate amount of diluted neutral detergent (3) The order is to paste and adjust the position.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I am repeating this LED Blinker on my Yamaha car.
[How is it used?
I installed this product on my 2014 YZF-R1 Rearfor Blinker as a LED winker conversion. (I'm considering to convert Front to Built-in)
Was the one you received as per Image?
As a YamahaOEMLED Blinker, it was small in size and true to its image.
Was the installation difficult?
Since I have an external Fender Eliminator on the rear, I used the included RubberSpacer to add bulk, but the body just barely sticks out.
How was your experience with it?
If you install it as it is, one-third of the body is hidden by the width of the License Plate, so I raised it with the included SpacerRubber. It may be possible to consider further raising the height with a few more centimeters of Spacer.
[Included Parts:were they on?
OEMRelay-compatible resistors and Brackets were also included.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Opinions and requests to Manufacturer
I would like to sell from Body1pc. as a part, as a supplemental part.
View detail
OEMQuality
Since I bought my MT-09 used, it came with this.
I replaced the Tank, so now I bought a new one and stuck it on.
I think Parenthesis is good because it matches the design of MT-09.
It seems to be durable, but the surface of the first one that was attached to it had a WHITE look to it. Is that due to the material? I guess it can't be helped.
Since the base paper also serves as a pattern for pasting, I think it can be pasted on Beauty.
View detail
Mounted on Mt09sp2022
If the Seat is not removed and worn, the Logo on the Tank is hidden. Also, some air was getting into the tank. View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Installed on a Racer 900GT
I installed it on a 2020 Toracer 900GT.
I purchased the LEDs because other manufacturers have been using LEDs for quite some time now, but Yamaha is still using bulbs at this time.
The installation is a little troublesome. The front panel is double-layered where the blinker is attached, so the inner panel is screwedQuantity:Quantity 2pc and special clasps:2pc. The Rear side is easier to work with if you remove the license plate bracket. And Quantity:Pair (for Left and Right) I put the resistor inside the Seat Cowl on the Rear side, but I think it is better to avoid the plastic part because of the heat generated. I did not want to cut the OEM wiring, so I bought a Conversion Connector and installed it, so there was no wiring. I am happy with the way the light shines differently than the OEM.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I wish they had put this on from the start.
I was feeling frustrated by the fact that the XSR700 2022MODEL was an LED Blinker (lol).
Originally, we were dissatisfied with the shape of the blinker, which was blingy, so we decided to replace it.
Looks Parenthesis better as I expected.
I had it installed at the shop and it took quite a while.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Mounted on MT-07
It was installed on MT-07. It came with a resistor, but I was concerned that it would get very hot, so I stopped using the resistor and used the Led Blinker Relay. I am very satisfied with the brightness when I turn it on.
After about 6 years of use, one of the LED lights went out.
There was a symptom that the inside of the Lens fogged up a little when driving in Large rain.
(Although the cloudiness disappeared after one night.)
View detail
Just fit
As expected of an OEM product, it can be installed without any discomfort.
The disadvantage is that the price is high.
View detail
usually
It is used for MT-09SP, but it is a very ordinary tank pad
Quantity:Pair (for Left and Right) The triangles on the SP are not attached to the SP's paint
View detail
Fits: YAMAHA NMAX, YAMAHA NMAX155, YAMAHA MAXAM, YAMAHA BWS125(BWS), YAMAHA CYGNUS X SR
Color:Unpainted but highly textured
I bought it in White:Unpainted, but the OEM Blueish white cocktail and the color is The texture is surprisingly good because of the similarity and sheen
I painted it because I wanted to match the tank and the color perfectly, but …
But if possible, I'd like CaseBody to be Standard Equipment from the start Where
It seems a bit pricey to buy this alone
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
No problem at all with OEM Product only
I bought a Carbon Style,
Texture is the best.
It works without problems with the attached Relay. Relay itself is not as big as it is told. In my case I put it in Space under Rear Sets.
To good things, Quantity : 1 Set of 4pcs. I would like you to lower the price and sell it.
View detail
It is recommended to make a single buy
Everyone who bought YAMAHA.MT-07 knows that the change is a must! , After changing the performance, of course, you need to change the appearance. When the cheating is to buy a full set of patches, it happened to be bad. So I couldn't make a single purchase at that time, otherwise you can save a lot of money. This time, I will pay more for the postage , Who said that only Webike has this product. The riders who bought YAMAHA.MT-07 know that change is a must! After changing the performance, of course, you have to change the appearance. When you want to buy a full set of patches, you just need to buy this piece. So you can't buy it at the time, or you can save a lot of money. This time, you have to pay more for the whole pain. Who told me that only Webike has this item.(translated by Google Translator) View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
The price is expensive - - -
Headlight, Tail lamp is a LED bulb, but it was only a light bulb, so I was concerned despite being invisible while driving, so I replaced it because of my mental health.
I could work with Electric Works Pliers and Spanner, Socket wrench, Hexagon without feeling difficulties.
In Front Side Panel's lining installation method, Washer with nails is bite in three places and I did not know how to officially remove this Washer, push up a little by little in the direction to remove the nail with a thinner Driver ahead Did.
Washer with detached nails flattened the nails with Pliers and used again, but the problem was not felt in particular.
Resistance is also attached to this product, and 4 places (Quantity : 2 Set) When exchanging Quantity : 2pc. Use Set resistance.
Our tarcer has attached resistance to Rear blinker but in order to fit in the gap under Seat you need to warrange longer while tentatively assembling using Wiring of OEM's Blinker. If there is something to be aware of in installation it is about this.
After installation, we are satisfied with OEM that Blinker got smaller and fearless and became fearless face. I can not see it while I am on the train - - -
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I think it's good.
I installed it in MT-25 of YAMAHA. Because Front was too long, it cuts a little and connects. Rear lacked Length, purchased separately Bullet Terminal and Wiring and extended. Resistance to Front LeftRight or RearQuantity : Pair (for Left and Right) I have to attach to. Just wrote that resistance has sometimes heat, Rear side is stored under Seat and Wiring is dense, so select Front side. However, the Front side did not have the space and had a bit of hardship.
After installation it is moving normally. The appearance is smart. Just wish Cost will fall a little more. I think that it can not be helped because it is an OEM product. Comprehensively Large satisfied.
View detail
There is only OEMOption and it is solid.
There is only OEMOption and it is solid.
I do not have the price, though - - -.
EUROYamahaTop Case 39L is installed, but there is almost no play.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
The shape is also good as Parenthesis is good!
If you thought that the shape is also good as Parenthesis well analogous products have been commercialized from Wa Big! This one is cheaper - - -. The feeling of having felt early - - -. I wish I had goodly scrutinized it. View detail
Makeover
I purchased it with Side Cover Mesh and installed it. Because I needed to remove Tank Cover and Side cover respectively, I was not confident of working a little, but as a result, there was no problem with Cover removal picture attached to the product, there was no problem.
Work time was about 1 hour each with Tank CoverMesh and Side Cover Mesh. In my case, I did not know that the picture above was attached and I had not seen it beforehand, so I think whether it will end sooner if preparing in advance.
After installing to Cover, I thought that the color was stronger than the imagination, like a picture, though it was somewhat flamboyant, but when actually attached to the vehicle, the Mesh part was not so conspicuous as to be downward, so it was satisfied as Image I am in.
View detail
Among the many MT-09 screens, the sense of unity with the car body is Number one
Until now I have been using the outside screen of overseas Manufacturer, but when I review it again at some time Screen seems to be overly head to head, looking for a thing with a sense of unity with the car body I found this product and bought it.
【What made you decide the purchase?】
Although I knew this Screen itself from before buying a car body, I thought that it was not particularly cool either at first but thought that it was an ornament with no wind protection effect.
However, when I review it again at a certain time, it will be a compact impression with Sharp by wearing it, I thought that the feeling of unity between the car body and Screen will increase and it will be more comfortable to purchase.
【How was it actually used?】
I think that the sense of unity with the car body increased and the atmosphere became more Sharp.
But it is natural but there is no windbreak effect. It would be better to think that it is about the blindfold Cover behind Meter.
Rather my purpose was to cover the gap between Meter and Headlight and to hide the Wiring classes behind the Meter so we needed it enough quality.
【Mounting was difficult?】
If you have Hexagonal Wrench and Phillips Screwdriver you can exchange very easily.
Quantity : Pair (for Left and Right) Let's carefully read the Instruction Manual and exchange it so as not to mistake the Bracket of.
【Please tell me the installation point and hang】
Screw fixing Screen and Bracket is Material : Let's be careful not to tamper as it is Plastic.
Since I may frequently detach from Custom, I exchanged Screw for Stainless Steel 's thing.
[Is there anything I was disappointed about?]
There is no windbreak effect, but I do not think that it was disappointing because I did not purchase this screen for that purpose.
Screw to fix Screen and Bracket for a moment is Screw Material : Because it is Plastic, I think it was Standard and BoltorScrew which is cool-made from Gold Genius.
【Hope for Manufacturer - Please let me know if you have any improvement points]
this [Contents] In 1. I thought that 50,000 is too high to be honest.
I think that it is still convincing price if it is about 10,000 yen JUST ....
【Have you compared items?】
None.
F. It is transfer from FABBRI's Sports Screen.
Screen was pretty good and I liked it in Extreme atmosphere, but since Screen is on the standing side, if it is combined with the thin MT - 09 of the buttocks it becomes a bizarre appearance and it will be replaced with the product of Y's Gear I made it..
[Others]
Material : I think that it is roughly good product except for PlasticScrew.
If you want to emphasize the Compact and Sharp of the car body by dividing the windproof effect, I think this Screen is an iron plate.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I liked it because the design was high though it was expensive
I attached it to MT-09 TRACER. Although it was expensive at the time of purchase of the vehicle, I had to wait for purchase, but other products etc.. While I was looking at, I thought that this was a good purchase. Installation was not so difficult, but it is MinusPoint that I must process Wiring ~. I hope I can make it a little cheaper! View detail
Measures against insects
MT-07 is the coolest without Screen, but if you do not install Screen, Meter will be outrageous ahead.
Yes, it is an assault charge.
If you do not install it you will have severe eyes.
Large off by the ratio of insect control 4 and wind protection effect 6.
And the windproof effect is so fair. Wind does not hit the torso from the neck down.
Well, I'd like to say that I'm going to close Bench first when Helmet's Ventilation full throttle is about to break my neck.
If it is 120 kilometers to 130 kilometers, this screen will be Large. There is no problem..
I chose Clear.
Again MT-07 is not cool without Screen. So, it's a bad challenge to Clear.
View detail