Reviews
Large and Cool
I bought it because I set the Sprocket to a Large size to use it in Race, and it contacts with the NORMAL Rear Fender.
The position of the Chain Cover is also made higher, so it could be installed without any contact.
Fender is also getting cooler with a larger size.
View detail
Buy Rear Fender
I listened to the music with good texture and Stylish.
I was concerned that the NORMAL Rear Fender was too short and the Rear Shock would get dirty, so I am glad to hear that my worries have been solved?
View detail
Excellent product and service
Excellent service and products. Good delivery times. Communication was great also. Would recommend to anyone. Will be using again in future. View detail
Presumption of painting
Since it is longer than the OEM Fender, it will provide some protection from sand, but it will be placed near the Mono Suspension. Also, if you don't paint it or add WrappingSeat, the white FRP corner surface will be noticeable from the back, so if you buy FRP, it is better to install it after you become a person who cares about it.
The work itself is easy for those with small hands.
View detail
The mud splatter was so bad.
[How is it used?
Commuting, Touring
Was the one you received as per Image?
Yes
Was the installation difficult?
Installation was easy, but I had a hard time getting my hand into the place to stop the lippet.
How was your experience with it?
Mud splatter was reduced.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
RCVSlit Front mask for CBR250R mc41 early stage
I bought it because I fell in love with the way it looked.
The dimensions were quite Gap.
View detail
Mc22 great mod
Good quality and adds a great look to the bike. Either as a race bike or as a race look with a mono light. Really easy to install just a srewdriver needed and about 5 minutes! View detail
The paint job is too shoddy.
It has Black stains and the paint is slightly peeling and bumped. View detail
The fact that Lineup exists is a miracle in itself.
Purchased for use at a driving event.
It is a miracle that there is a Lineup even though the car is out of print. Thank you for making it.
It is very difficult to find parts that are no longer in production, but we are very grateful to Saiya for still making them.
It will take some time for delivery, but if it is available, the wait will be exciting.
View detail
Although it is the 2nd piece, the result is good as usual! Arrival is also early!
Although it is the 2nd piece, the result is good as usual!
Arrival is also early!
View detail
Since the friend attached, it purchased. Attachment is dramatically easy and easy also for beginners. After attachment became very smart! It is admiration up custom rather than changing a muffler! Please try! In the direction which has rem
Since the friend attached, it purchased.
Attachment is dramatically easy and easy also for beginners.
After attachment became very smart!
It is admiration up custom rather than changing a muffler! Please try!
In the direction which has removed the exhaust air cleaner, it is recommended further!!
View detail
more than expected
Compared to replacing a Single Seat, it is inexpensive, and it is a good cosmetic product with direct information from Motorcycle. View detail
Installation on SP Tadao Exhaust System (not compatible, modification required)
I was looking for an Under Cowl that could catch oil, and I found this product and ordered it.
The installation was confirmed as AKRAPOVIC Exhaust System, but we have replaced it with SP Tadao Exhaust System (POWERBOX FULL RS), and the expansion chamber part is cylindrical, so we purchased it on the premise of modification.
After confirming that the rear end would hit as expected when actually installed, the necessary area was shaved off a little at a time to match the actual product.
The object is cylindrical in shape and the under cowl is also inclined, so it did not go as expected. After repeatedly removing and shaving, shaving and matching, we finally secured clearance with the expansion chamber, and when we tried to install it, the screw position did not match slightly.
After forcibly installing it and rechecking the clearance, I found that the expansion chamber at the rear end was not hit and the parts at the mounting point were loose enough to allow for some adjustment without tightening the bolts, but when I looked underneath, I found a moccoli that looked like the forward part of the expansion chamber.
I thought about cutting up this area as well, but it would be a complete disaster if the oil receiving function is lost, so I decided to put Heat Insulating Material on it for now and see how it goes.
I completed the installation and test drove it to lightly fill it with Gasoline, but it smelled a little burnt? I thought I would give up and drill a hole in the oil receiver if it burns, since I usually remove the oil receiver rubber plug.
This time, it was installed outside of the conformity. I wished the bottom was 5 to 10mm lower and the back end sloped back a little more, but I am satisfied because it is almost exactly as in the Image.
View detail
Quality is top notch!
Fitting was quite good and easy.
It was fine as is, but I painted it with a paint I had at home and I think it has excellent cost performance. I made a mistake in choosing the paint, so I may repaint it one of these days.
View detail
be fascinated by
Although it is a part that does not need to be installed, I did not expect such a drastic change in impression with such a simple installation. I can say with confidence that the parenthesis is too good. The installation is super easy, and it takes less than 10 minutes if you have a driver&Spanner&Pliers. The only thing I am worried about is that the area around the Sprocket is mesh and the clearance with the Chain is about 5mm, but it is around the Sprocket, so it should be large enough, right?
Paint "As a paint base..." but I would like to keep it that way for a while.
If I had to ask, I'd say another 20-30mm longer.
View detail
Fits: YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3
Wet Type with excellent gripping power!
[How is it used?
Tail cowl and seat base are of course made by Saiya.
I think this is basically FOR Repair. I thought it was an Upgrading item.
When you buy a Tail cowl, you think it comes with Standard, but when you buy a Tail cowl, it comes with Quantity.:Seat rubber is also set.
It was High PERFORMANCE.
Was the one you received as per Image?
It was just like the Image! I wanted this Wet Type!
Previously, only the dry type was available in the lineup, and the dry type was not durable.
I disliked it because it would fall to pieces and lose its Grip power when it started to fall apart because it was defeated by my buttocks.
So, until I learned about this product, I had been using Magical racing's Wet TypeUniversalSize
It was cut out and used.
Was the installation difficult?
It is cut beautifully in the shape of the Seat Base, so there is nothing difficult about it.
The best place to put it is on the floor, so we carefully degrease the surface before applying it, and also try to find the best place to put it by actually sitting on it.
If you Masking and apply it carefully, you will not make a mistake.
Since the adhesive surface is strong, it is not possible to reapply the adhesive once it is attached.
How was your experience with it?
It's great. Grips well and lets me concentrate on Riding!
[Included Parts:were they on?
None. This product only.
[Was there anything that disappointed you?
Not on the product itself! If I may say so, it would be even better if the Cut was a little more Large and the Rider could be adjusted as desired.
View detail
splash of mud
Rear tire mud splash prevention, looks good, so this is installed.
Works great for rain, puddles, and mud splashes.
It is a nice product with a nice look and feel.
However, the fixation method, Tie Wrap, is not quite right.
It is unfortunate that no consideration is given to prevent scratches from mounting and vibration.
Was it a bit unreasonably fixed? Long-term use seems to cause Cracks to enter without being noticed.
If the fixing method, scratches and cracks caused by vibration were taken into consideration, there would be nothing to say about this product.
View detail
Saitaniya Tank Cover/Full Covered/Tank End Original Shape
MV AGUSTA F4RC RepartoCorse-MOTUL also
I've already purchased the same manufacturer, so it's not a problem;
SaitaniyaTank Pad for 2021 MODELKawasaki-Ninja ZX-10RR
I asked the store to install it for me.
Because it's a full cover? It cracked on the second day of purchase.
Especially every time the bite part rides and banks.
It's cracking and splintering. The bubbles are terrible.
[Angle] The white part of the picture is the crack that was repaired. The other side is also amazing!
I'm riding a restored Aron Alpha.
But it looks good, so let's call it good.
View detail
Saitaniya Tank Pad (Twill weave) Carbon
I also had it on my DUCATI Panigale 1199R.
It's the usual Manufacturer.
For 2021 MODELKawasaki-Ninja ZX-10RR
The SaitaniyaTank Pad was terrible, but…
This one is good work.
[Why? The quality of the product is similar to that of the same manufacturer.
View detail
Cool!
It's expensive, but it's cool.
I'm not complaining because I'm buying cool at Gold.
If I may say so, I was wondering if Brackett could offer a few more suggestions.
I decided to accept the fact that it was a Cowl shop.
View detail