Reviews
Fits: DUCATI panigale, DUCATI panigale, DUCATI panigale
Also available in 2021 V4
[How is it used?
Used in 2021 Panigale V4 SP.
The STAND side uses J-TRIP's Front stand.
Was the one you received as per Image?
Yes.
I had also bought another boss for GROM, both of which were Gold alumite processed.
Since the Motorcycle and GunGun rub against each other, I think it will eventually peel off even if it is anodized nicely.
I think it should be more martial…
Is this the reason for the SPECIAL Knife?
How was your experience with it?
First of all, you didn't mention what year it is compatible with, but it is also usable with the 2021 Panigale.
If the Universal boss is left in place, the vehicle body and STAND will hit each other.
I know there is a way to lift up the bottom of the front fork, but I wanted to use the front stand because I was afraid of attaching and detaching the wheel, and also because I thought it would put too much load on the front fork.
Being a dedicated product, there are no problems at all with accuracy or usability.
Just overpriced…
[Points to note]
The front stand cannot be used on Panigale unless the stem hole is removed, because the stem hole is still blocked.
Let's remove the StemHole cap. (I removed it by poking it from the Top Bridge side.)
How did it compare to other products?
Fork up stand was considered, although I don't have one to compare it to because it is a dedicated product.
However, I really wanted to use the front stand that I have now, because it is difficult to find a place to put it when it is covered with STAND.
View detail
It's solid.
It is indeed a Manufacturer's product! I use it with peace of mind. View detail
Excellent stability
Purchased in conjunction with J-TRIPShort lowlerRear stand
Stand Hook is already pre-installed.
It's a V receiver, so it's very stable.
View detail
Required when removing Tire.
I usually use Stand for Beginner.
When you remove the tire, you are using a V-bracing system, and it is nerve-wracking when you are handling a heavy motorcycle. If you're not careful, you'll end up on the ground.
View detail
Purchased for Nankai's NJT-1052BL!
I bought the L-Shaped Receptor for the Rear Stand collaboration between Nankai and Jay Trip.
I was able to install it without any problem because it is the same manufacturer.
If the L receptacle were a little deeper, I could make the STAND more stable.
View detail
I knew it was a special product...
[How is it used?
I purchased this product because I needed it for front maintenance of my Grom JC92.
Was the one you received as per Image?
The color was as I imagined, but the color was only Gold (Black at the time of sale?), so I thought it would be better to replace it...
Was the installation difficult?
No problem, just plug it in.
How was your experience with it?
This is a special product and can be easily lifted up by simply inserting it into the round hole at the bottom of the Stem. However, it is recommended to check the hole when inserting it to avoid hitting the Special Knife boss on the body....
[Included Parts:were they on?
No, sir.
[Was there anything that disappointed you?
The construction of the product is perfect, but I feel that the price is not commensurate with the quality.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I've been wondering whether I should buy a JT-113 or a JT-116 since I bought my first Grom, but I decided to go with the JT-113 because I have a JT-116 that I've been using for a while. The JT-113 is fine for maintenance around the wheel and brake, but for overhauling the front fork, the JT-116 and the SPECIAL Knife boss are better, so I decided to use this one. Also, I think the price is still too high.... If the price was at least 3,000 yen, I think everyone would buy the Grom Owner without hesitation, but what do you think? Also, if there were more color choices, it would be more enjoyable.
View detail
Fits: HONDA CB1000R, HONDA CB1000R
This is a dedicated product, so the system is outstanding.
I bought this for my CB1000R. I am very satisfied with the quality and system. It is very easy to install, just insert it into the maintenance stand and fix it with CRing. However, the "Shaft only." If you think about it, the cost performance is not good. View detail
watchman
I bought this for my J-TRIPSTAND. I chose the V type because it is more stable than the L type. View detail
Fits: HONDA BROS400, HONDA BROS650, HONDA VFR800, HONDA CB1000R, HONDA VFR750F, HONDA CB1000R, HONDA VFR800, HONDA Bross 400, HONDA Bross 650, HONDA VFR800, HONDA Bross 400, HONDA Bross 650
Fits CB1000R (SC80) 2021 model
It attaches to the cantilever STAND (sold separately).
This shaft is compatible with the 2021 model year.
I was quite reluctant to insert it, but after applying Grease, it fit perfectly.
To use STAND-UP, stand the motorcycle upright, then step on the STAND with the right foot and apply force to raise the motorcycle upward.
You can do it alone.
View detail
It's a very good idea…
I bought this because I was worried about it coming off when I lifted up in the V by myself.
Since the Hook and the receiver are fixed, the sense of security is perfect, but the moment I lifted up, it was torn off.
Did I use it incorrectly?
But I understood how it works, so I bought a slightly thicker Rubber Band at 100 yen and wrapped it so that it would be fixed in the same way.Rubber Band is cheap even if it breaks, so I started using Rubber Band after that.
View detail
It is a large important Parts.
I glued it on, and it fits!
Please protect your expensive Swing Arm!
View detail
That's perfectly fine for a beginner.
If you watch the instructional video, you can lift up easily and safely.
I've gotten used to it and now use it on my V-Hook.
I'm glad I bought it. It's definitely a STAND you should have.
I think it's no exaggeration to say that it's a must have for motorcycle riders.
View detail
State the dimensions.
Nowadays, I don't understand the sensibility of selling such attachments without stating the dimensions.
The product itself is not particularly problematic, but depending on the condition of your Swing Arm or Hook, the Rubber cover may fall off every time you raise or lower it, which may be annoying.
View detail
PRO-like
I heard that it is easy to use the first time, so I decided to use the V receiver.
It was easy to adjust the width and height, and the product was friendly to me as a first time buyer of a Maintenance Stand.
View detail
Easy
When I changed from GSX1300R HAYABUSA to BMW900XR, I couldn't use the V-shaped receiver, and I received Quantity for the first time.:I was worried about the strength of the shaft because there were some examples of bent shafts in the reviews, but there are no problems at all so far. In my case, I only need to clean the wheel and maintain the chain, so this is enough for me. View detail
Rubber might be weak.
On the lower part of the Swing Arm of BuellXBSeries, there is a protrusion to prevent slippage when using the Racing Stand, and if the receiver is placed on the protrusion, the rubber part will be torn in pain as soon as possible!
I rebuilt the tool Grip Rubber with a liquid Rubber making, Plusty Dip, and the rebuild worked!
View detail
Easier to Lift up than to Receive L
I used to use the L receiver on my Ninja 1000.
This time, it was changed to V receptacle for 21’hayabusa.
As usual, the quality of the product is fine, and I feel confident in Maintenance.
View detail
I was worried about falling over, but it was easier than I thought.
I was worried about tipping it over before I used it, but it was easier to operate than I thought and I was able to easily lift up the vehicle. It is also easy to release and I have no worries about it falling over. I think the quality is high. I used it on my 2022 New Model GSX1300R HAYABUSA. View detail
APE 100
Used for APE 100
It is the use with Racing Stand HookV type Hook of SHIFT UP in XR100Swing Arm!
J TRIPNarrow takes the V-Hook to the ground in a twisting motion!
Limit. Still Quantity:Pair (for Left and Right) I think that the current situation is the limit because the application becomes shallower than the two liches, although it can be inside about 2cm.
SHIFT UP's Racing Stand Hook is an inside type, so there is a part that can only be done, but …
It's two-light, so no problem at all for use.
View detail
Japan quality
The front stand of the jTrip that I used until now was used without a problem, but when I started to lift the jc92 glom, the headlight collided with it and it was impossible. If I detach the headlight, I can use it, but it's too much trouble with Visor on. I thought about making my own, but it was not worth the materials and processing time, so I bought it, although the gold price is high. Easy to use
The problem was solved without any glitches. Parenthesis is nice with Gold alumite again!
View detail