Reviews
You'll feel better acceleration, but the embracing will not work.
[How is it used?
Commuter Main
Was the one you received as per Image?
Yes
Was the installation difficult?
it's simple
However, the included instruction manual is WhiteBlack and halfway detailed, so it is difficult to find the orientation.
Also, the arrows were reversed.
When in doubt, try breathing in and out. (Mouth) is the Engine side.
How was your experience with it?
As others have said, the Response and acceleration feel is something better.
Embellishments will not work lol.
For those who use a lot of embellishments, it will be weird until you get used to it.
It is not suitable for driving on a mountain pass or something like that because the embellishments will not work as well.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Almost pontooned ??
Image didn't change as much as I thought it would. w
The seating comfort is about the same as OEMSeat!
View detail
Expect ResponseUP!
I bought a Z125pro and due to snowfall in Hokkaido, my car hibernated before I could ride on public roads. I installed it because it was highly rated in everyone's Impression. I don't know how it compares to the other ones, but I'm looking forward to the next season! View detail
Attached to Bore UPEngine
Installed on a LITTLE CUBFIEngine with 88CC bore.
It was installed without any problem, but when the Center Stand is raised vigorously, it hits the Exhaust System.
The Sound of with Baffle is my favorite, but people around me say it is too loud.
I was worried about the design and the Exhaust System Up Type, but I am glad I went with this one.
View detail
Recommended for those who focus on volume.
First of all, it is very difficult to tighten the Silencer bracket with the CharcoalCanister without removing the entire footpeg set.
To install the footpeg without removing the entire footpeg set, a palm-sized Small Type Swivel Ratchet can be used.
It may be for people who have a little bit of work sukill
I used to use BEAMS, so this is a comparison with BEAMS, but the good thing about BEAMS compared to BEAMS is that the baffle can be removed and it looks cooler (laughs).
If you remove the Baffle, it will sound like a stupid explosion.
It's all over the place and you can't make any progress at all.
I bought this because the BEAMS Exhaust System was too Large, but I returned to BEAMS after about a month,
If you are thinking of buying a new one, I recommend you to go for MORIWAKI for a little more than 10,000 yen!
View detail
Rod Silencer Exhaust System installed on MOTRA
The exhaust pipe of MOTRA's OEM exhaust system was rusted and broken, so I selected this exhaust system made by WILLS WIN from among the external exhaust systems. It is made of AllStainless and the goodness of the cost performance which can be bought at 10,000 yen was the decisive factor of purchase. I thought the appearance was quite good. The exhaust sound is not too loud and the exhaust pipe of MOTRA's OEM exhaust system was too thin and the maximum speed was only 55km/h. But after replacing it with this exhaust system, 60km/h is now possible. But after replacing it with this Exhaust System, 60km/h is now possible. (I have a Class 2 motorized vehicle registration.) The exhaust pipe near the Mount Bracket was cracked by vibration. I can give up because of the price. It might be because of the vibration of my engine. It is necessary to take measures against vibration. Please be responsible for your own use of this product. View detail
The seat lock is hard, but overall I am satisfied.
We are 168cm 66kg with short legs and bought a new PCX160.
I knew I was on my toes at the time of the test drive, so I decided to buy it.
The product was not in stock at the time of order and took one month to be delivered.
The good:I feel like I'm 2cm lower, if not 3cm.
Satisfied that Helmet storage space is the same as standard Seat as described in ManufacturerSite.
Bad point:the rear is floating about 2 cm before applying Seat lock, but the lock is engaged by pushing hard.
I checked with the Manufacturer to be sure, but they said it is only a special order and that is normal.
Seat is still thin and buttocks are somewhat sore.
Overall, I recommend it because it holds Helmet storage space and improves the footing!
View detail
Fits: SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER
It may not be enough for those who like a large sound.
It is a fairly quiet Exhaust System.
I thought about removing the baffle, but it looks like it's built-in and welded on, so I decided against it….
Good thing it's a neighborhood friendly Exhaust System sound. ( ´ ▽ ` )
View detail
Parenthesis OK
I bought this for my CUB. The style of installation is good! However, the top speed is down and the sound is too quiet. I think it's best for slow city driving, but not for touring etc... View detail
Fits: HONDA CT125・CT110 HUNTER CUB, HONDA CT125, Hunter Cub
Damaged!
It was a very nice product, but after a few months of use, the L-shaped part got a crack and was put in storage....
A little more strength would be nice.
View detail
reduction embrasure
I purchased UniversalValve and installed it on my GSXR125.
I didn't have the dedicated Valve in stock and the price was a little lower than I would have liked?
Valve side is too thin for the inside diameter of the Hose, so it is too gubby! I tightened the Hose with in-hemp palm, but it came out easily, so I changed my strategy. I used a hose for air venting, but it was too thin to fit into the valve side, so I cut the hose into a C shape and inserted it into the valve side. Cut the Hose to fit the Valve side. This is the only way to prevent the gap between the Valve and the Hose. I inserted the Hose there and fixed it with a double layer of in-hemp palmock. I will use the Band in the Home center to set the quantity.:2pc. Set purchased, cost about 600 yen. 。 As a future project, I plan to make the gap-filling Hose black-colored and oil-resistant, but it is more expensive than the transparent Hose, so I should have bought a dedicated one (laugh).
I think that the Sprocket is set to Acceleration, so I think that it is now the NORMAL embellishment.
Response is getting better.
I will be spraying parts cleaner periodically as it seems to slow down the valve movement.
I will remove it when it gets colder, as it seems that the Valve can freeze in the winter due to condensation.
View detail
Mounting orientation
I installed it on my VOX.
Engine braking reduction cannot be experienced unless the speed is fast.
When the Axel is returned, the effect of engine braking is weakened.
There seems to be an improvement in fuel economy, but I have not experienced it yet.
Startability is better.
Installation can only be done by removing the cowl, but the tool is large and sturdy, using only a Phillips screwdriver.
View detail
I did not understand it well.
I looked at it expecting it to be effective, but I didn't really understand. View detail
Might be a good thing for someone who often turns the Engine and rides it.
I installed it on my CROSS CUB50 and to be honest, it didn't turn out the way I thought it would. I installed it on my CROSS CUB50, and to be honest, it did not give me the feeling I was expecting. It is true that the power at high rpm is great, but I tend to use it at low and mid rpm range, so it was difficult to use.
It is a good thing to have for the fastest Attack.
View detail
The texture is good, but the low-speed Torque...
[How is it used?
The OEM exhaust system of LITTLE CUB had the shape and sound of a CUB exhaust system, so we decided to customize it to change the taste a little.
[Was it as per Image?
The quality is good for the price, especially the exhaust pipe part, which has the unique color and luster of stainless steel compared to OEM plated steel. The exhaust pipes, in particular, have a nice color and luster unique to stainless steel compared to OEM plated steel.
Was the installation difficult?
The exhaust system body is lightweight, and the silencer and exhaust pipe are integrated into one unit, so there is no need to join them together. However, when replacing the exhaust system, make sure to replace the gasket with a new one.
How was your experience with it?
The sound quality has become a bit more bass-oriented with a single cylinder sound, and the volume has increased moderately. The sound quality and volume are not so loud that it is bothersome to the driver when driving in a normal environment. The overall length is also much shorter than the OEM exhaust system. However, the low speed Torque will drop after installation, so you may feel nervous from the time you stop until you reach a certain speed.
[Included Parts:were they on?
This Manufacturer's Material:AluminumEmblem came as an attachment, double-sided type.
[Was there anything that disappointed you?
I don't know if this is a product error or a problem with the car body, but when the Center Stand is raised, there is a clicking sound.
I saw that there was no contact with the Exhaust System, but the Brake pedal was touching, so I had to make a minor adjustment. I would like to make sure that the clearance with the car body is Large and strong during the temporary installation.
View detail
Color does not match.
The colors included with the product did not match, so the front and rear were swapped and installed.
The texture and rigidity are very good. I am looking forward to seeing how well the texture holds up with use.
View detail
Ponting.
I installed it as a trial, but I am not sure how well it works. (Lol) View detail
![Front Pipe [For Full Exhaust].](https://img.webike-cdn.net/catalogue/images/42509/cbr250rr_front_pipe_street_a_TS.jpg)
o2Sensor is not received.
I bought this to use in combination with a cbr250rr yoshimurar11. o2Sensor did not arrive and I gave up on installing it myself and am looking for a store to do it for me. I saw in the reviews before I bought it that I needed an extension for the o2Sensor, but I wanted a WirusWin exhaust pipe. I have given up on customizing my own wiring etc., so I think it would be more efficient to check with a store that can install the exhaust pipe for me when I purchase this product. The product itself is a beautiful color and I can't wait to hear the sound when I install it. View detail
Hmmm, they're cheap.
The Fender Eliminator was cool and I put it on.
After installation, I didn't really notice it, but it looks very cheap. It is worth the price.
I appreciated the included Parts.
If there is something else you are interested in, that would be fine too.
If you are cheap and want to put it on anyway, it is possible.
View detail
Slight change in Engine blow up
The engine starts to blow up more lightly and the jerky feeling during engine braking is calmed down.
There are a variety of similar internal pressure Control valves on the market.
Body is Material:Plastic, so we thought it might be difficult to emulsify Oil.
We chose this product.
View detail