Reviews
It is overpriced!
It was installed in order to install Navigation and ActionCamera when touring.
Unlike cheap Chinese products, the installation was done with Bolt On without any difficulty.
The Oil Temperature Meter attached to the Handlebar is visible without any problem.
View detail
Fall Prevention at Circuit
I was looking for a bar end that also serves as a slider and came across this product, which is supposed to be fixed with a rubber bulge.
Tighten as is and installation is complete!
View detail
Updated in conjunction with Smartphone Holder
Along with the new Smartphone Holder, the Handlebar Brace bar was also updated.
It's neither good nor bad, I guess.
View detail
KSR80 Handlebar Replacement
It is a used KSR80 with 16,000Km mileage, but due to its age, there is a lot of rust on the details of the handlebar, and I decided to replace it because it is a place that is noticeable when driving. I decided to replace it.
I researched on some Reviews and selected this product which is close in dimension to OEMHandlebar.
The quality is nicely Anodized Aluminum Handlebar.
I thought it was the same size as OEM by research, but there was a slight error in aperture and height as shown in the picture. 。
When I actually installed it, I felt that the Handlebar was much lower, but since it was narrowed down, it seemed just right.
The OEM has a reinforcement bar welded together, but this product has an aluminum handlebar braze, which is very cool and I like it.
View detail
Daisan Keihin Spec.
This is the old Handlebar.
I am surprised that this product is being released in the age of harmony.
I liked the color of the Gold because it was glaringly different from the calm atmosphere of the Gold of posh.
If you install it in an air-cooled Large type four-engine, it will become the old Daisan Keihin Spec.
View detail
good
I installed it on my PCX.
I think there is just a little bit of Gap and I think I can prepare a suitable Washer to handle it.
The body itself is solid and satisfactory.
View detail
The Shaft and Clamp are the Quantity:It's a set, so it's good.
The color difference between Shaft and Clamp is good, the rigidity of Attachment is good and it is the best for MONKEY125. Unfortunately, the shaft thickness of the shaft is 2mm large and it is the best product (because the diameter is small for the installation of Drink holder, I was able to install the Rubber van Kamase). View detail
Itchy
I've been installing a USB power supply on my BMW F650GS I had to put it around the base of the Handlebar and it was interfering with the Tank Bag I wish I could attach it to the Handlebar Brace, and then it came out I jumped at it
Originally, it was to be installed on the Back Mirror, and if measured by Caliper, the 13mm F I was wondering if it would fit on the 650GS Handlebar Brace, but it works fine It seems to be able to relocate safely and become convenient
The product itself is mainly plastic, so I might be worried about water bottles and Ta Brett and other heavy items I don't know I thought the limit was per smartphone
View detail
Very good
Used on a millibarized Harley Aluminum Handlebar
Before the installation of this Handlebar Weight Does it really work? I was skeptical that the vibration of the Handlebar was too much by the harm of customizing Harley It became painful to hold the Handlebar after more than 3,000 rpm So I bought this reputable Weight, which I'm clutching at straws
It's very easy to install and it takes less than 10 minutes to replace both Sides
The result is a surprisingly low vibration I wish I'd used it sooner! I thought
View detail
It's more for Dress-up purposes than performance!
The Handlebar width is narrowed because of the replacement of the Handlebar I bought it because it became difficult to install the Smartphone Holder
Installation is easy, but the adjustment of mounting to the Center took a surprising amount of time
It is better to choose the size of the Handlebar after measuring the place where it is attached to the Handlebar is a good idea
I installed it for the purpose of vibration reduction, but I don't know the effect so much
I chose Gold with the other Parts and it has great color and is not cheap It's a place where you'll see it while you're driving, so you can indulge in self-satisfaction... ♪
Reasonable, but I think it's a very good product!
View detail
Is choosing Type a Drumstick?
The OEM's Handlebar position was high and I replaced it with Rear Sets, so I did not like the boarding position and exchanged it.
I worried about whether it is Row or Medium, but I did not know how much it would change unless you tried it, so I chose to select Row.
As a result, it became considerably lower than the OEM, the attitude also looked like a slump and it became quite easy.
I can not compare because I do not know other products, paint is also beautiful, Handlebar Brace is also attached, I think that it is worth buying.
However, although Seal? Is affixed to the bar, it is extra because it is necessary to peel off after all.
View detail
It is good.
After all it is a good Handlebar. I used Red color until now, but after 21 years
Anodized Processing faded, I replaced it because it became a mottled pattern.
Next time I turned to Titanium color which seems to be fading stronger.
The nice thing about Handlebar is that Handlebar itself absorbs vibration, so your hands are not numb,
Elbow and shoulders are also easy to get tired, even if you travel long distances, you can reduce the number of breaks.
Some people think that this softness is anxious, but I want to run a long distance at a stroke
I think that I brought it to people.
It is Handlebar which can not quit once using it.
Even compared to other Handlebar's price, it is considerably cheap, so please add another color for another change, another one
You can buy it..
View detail
I am satisfied..
I think that the price that I think is lighter and shock-absorbing than OEM is cheaper compared to others and I think that it is reputation. Medium is used for DT 200 wr but it was a form which was quite similar to OEM when arranged side by side for reference. View detail
Satisfied
Angle adjustment of GUYRA Shield Mount the gold fixture Measured because the mount was a cheap The same diameter as the Handlebar.
So before with Handlebar Brace Quantity : Pair (for Left and Right) Two places are 22. I remembered there was a thing of 2 mm and I thought that I should install it on it.
At that time incidentally totally 22. I found this item of 2mm. If this is the case now you can relocate anything attached to Handlebar and Handlebar will also become Snap and buy it as one stone two birds with one stone.
Result Large Correct answer.
View detail
There is Custom feeling
It was installed in 2003 dTRACKER.
Handlebar was decided to be Gold because the exterior was Black.
Yellow I was imagining a sexy gold, but it was an Orange-like gold. But I think that this color was good.
If you do not change the handling of Clutch Wire a bit, it is tight when cutting Handlebar to Left.
I could afford to change the way we walked.
View detail
Good vibes
Today, I purchased it at nearby Shop and attached it to CB 1300 S B.
Correct answer by choosing the same color Silver as Handlebar.
Easy installation is possible with 3 minutes as well.
I did not interrupt the AccessLine to the key.
View detail
It was good!
There was numbness in the hand with long distance touring, but it was improved considerably!
Quantity : 2pc. Since I purchased Set and attached it, 1 pc. The wearing feeling of minutes is unknown - - -
View detail
It's just right.
I used it with TriumphTIGER.
Because it is a Multi Motorcycle that can also run Off,
Hey, Handlebar wide and linear.
I feel a little Large in Japanese physique.
width - I feel just fine with both stops.
I feel a bit lower than OEM
I do not run Off-road, so it's a good feeling.
View detail
MappleHolder mounting bar
Touring mappleHolder I bought it for my own work. There is no dissatisfaction in the quality of the bar at all. It's even better if it's a bit longer ... I will make MapBracket from now View detail
This is enough!
It is HARDY's Handlebar. Since AC and USB power supply was attached to the Handlebar, it seems likely that a Bar pad can not be installed. Therefore, I looked for cheap ones. The price is also Reasonable and solidly made products, Anodized Treatment is also beautiful and this is enough.
As a hope Renthaletc. I think that it was good if there was Laser processing of mounting position angle like Manufacturer of.
View detail