Reviews
Purchased for Touring
I purchased this product for my GB350S.
Rear Carrier uses DAYTONA's Multi Wing Carrier.
I thought it was too large for the Motorcycle size, but it was just the right size.
Installation is as simple as bolting the attached Base to the Carrier.
When running empty, it made a clattering sound, but there was no particular problem with driving.
One point of concern is that if you put the Key in the locked position while it is open, then close it from that position and press down, the key will
The cost will be high, so care must be taken not to marker it.
View detail
![[Repair Parts] Same Number Key (3pcs.) [Z180]](https://img.webike-cdn.net/catalogue/images/68106/15177_TS.jpg)
Used for GIVI E21
GIVI's E21 key was damaged and was replaced.
I was worried about whether I could use it or not because the product description only said "Universal", but I had no problem.
It worked. Although there is an inner groove Key set Z1565T for keys with E21 listed in the compatible MODEL,
3pcsQuantity:Set is not set, so it is more expensive. I think this product is sufficient.
View detail
![Rear Box [E30RN]](https://img.webike-cdn.net/catalogue/images/75563/16976_TS.jpg)
I think the structure that allows the key to lock even when it is not completely closed is defective.
I have used several types of LargeSmall cases for GIVI products, but this is the first time for me to use the MonoLock type.
The old locking mechanism of early products, where the lock would get caught on something and prevent the door from opening, has been eliminated, but the fact that the door is locked even when it is not locked is a large drawback. Of course, the root cause is that the user does not check the well, but when I was in a hurry, I ran thinking that I had closed the door and was in a hurry to see if I had lost something after arriving at the destination.
It would be nice if the structure of the key could not be turned if it is not locked as in other companies' products, but I wonder Large why such a structure was chosen.
View detail
![Mono Lock Case [E43NTL-ADV]](https://img.webike-cdn.net/catalogue/images/32552/95342_01_TS.jpg)
Large doubles as Small
I used to use a 30L Top case, but I wanted more capacity for camping touring and other activities.
I took the plunge and bought this Case, which holds 43 liters, if I had to buy it.
As a result, I am Large satisfied.
I go to hot springs and buy souvenirs even for day-touring, so if this is all I have, I can use OnsenQuantity:Set + souvenirs can be easily accommodated.
It is very convenient and can easily accommodate a Bag to be used when getting off the Motorcycle.
Camping touring can also fit the luggage, so you don't have to worry about loading it.
The Silhouette of the Motorcycle is a little too Large, so the Motorcycle Silhouette seems to collapse a little, but it is much more convenient than that, so I am satisfied with Large.
View detail
![Special Rack [SR3117]](https://img.webike-cdn.net/catalogue/images/91664/17693_01_TS.jpg)
Many Parts (Screw/Screwetc.)!
I had no choice but to buy it in order to install GIVI's TOPCASE, but I haven't installed it yet because of the number of screws and other parts. I would like to install it before Camping touring in the fall, but the rigidity of the case is so strong that it may be too large to install.
I used to tinker with various motorcycles, but that was as a student when I had time. Now I'm so busy, I don't know what to do...
View detail
Installed in 2023 MODEL.
Since the MODEL has been changed from Mounting Boltm6 to m8 since 2022, a little modification was necessary. View detail
Tank LockBag is convenient to use
I used GIVITank LockTank Bag in FJR. As you know, it is very useful because it can be detached with one-touch, so I do not have to take it off when I take a break. This time, I added a CRF250L to my CRF250L, and although I can install it on the RALLY50, I cannot install it on the L. So, I decided to use the Tank LockTank Bag. Therefore, I purchased this product in order to use Tank LockBag as a seat bag. View detail
When in doubt.
I was wondering which CarrierCase to attach to my CT125, but decided on this one because of its light weight and capacity. I am satisfied with the Large size because it is easy to install and holds enough stuff. The only regret is that the Inner Mat is sold separately. But I am generally satisfied! View detail
![MONOLOCK Universal WIDE Base [MP70N]](https://img.webike-cdn.net/catalogue/images/29606/94540_01_TS.jpg)
This is for Large type box!
It can be mounted on MT-09GIVIFitting for Mono Rack without any modification. I had been using the B47Series on a narrower UniversalBase, but recently it started to rattle. I have changed to this WIDEBase and there is no more rattling at all.
We felt that WIDEBase is still more stable for Large type boxes.
View detail
Overall, a good evaluation.
I bought a W800, but I had installed a 46L Kappa rear box on my old W650 for the time being. However, the color of the box did not match with the body of the W800, so I searched for a box of the same size and purchased a GIVI box of the same size.
Since Kappa and GIVI are Universal, we are familiar with their installation and are satisfied with the color and shape.
I was impressed by the ease of closing the lid, which has evolved considerably since Kappa, and it is a pleasant sensation when the lid snaps shut.
However, what is somewhat disappointing is that sometimes it does not close. It does close after a few tries, but the cause is unknown.
I would love to see this improved.
The other thing is the high price. This time I bought it because there were more than 7,000 Webike Points, without which I would have hesitated to buy it.
View detail
just barely
Depending on how you put it in, it can hold a SHOEI x14 M and a GT AIR2 S, but if you make a mistake, it won't fit.
I was uncertain, so I went to the store to check it out.
View detail
Storage has increased all at once, making it more convenient.
[How is it used?
It is being used on a NMAX 155.
Carrier is made by Y's Gear.
I purchased this product because I felt that the storage under the seat was not enough to hold a full face helmet and that the amount of storage was not enough.
Was the one you received as per Image?
I bought the 33L because I didn't like the large size of the box while aiming for more storage, but it is surprisingly compact.
The rear view after installation is also comfortable, and since it fits within the width of the handlebar, there is no problem at all when slipping through.
Was the installation difficult?
I installed Base on Carrier made by Y's Gear, but I struggled a little because I could not decide on the Bolt to install it in a good place.
I was able to install it without any wobble, but I didn't want it to fall off, so I used Tie Wrap to secure it in two additional places.
How was your experience with it?
The feel is great, more versatile than expected.
The square shape allows for a wide storage width and prevents the creation of dead space.
The lid closes with room to accommodate a full face helmet (SHOEI GT-Air II with B-COM).
Gloves can be stored together.
On top of that, it can be stored under the Seat, which I think is a great combination with the Scooter.
A 6-can pack of beer plus several 500ml cans can fit in the bag, so it can be used for after-work shopping.
I have used it in the rain and it is convenient for my daily commute with no flooding. It is very reliable.
[Included Parts:were they on?
It came with everything without any problems.
[Was there anything that disappointed you?
I don't know if I can say this is disappointing, but it is subtly difficult to tell if the lid is properly closed once opened.
It is not closed by just pushing it in, "Snap" If a small sound is heard, it is OK.
Check after closing the lid is essential, as the key can be pulled out even if it is not tightly closed.
[Notes]
Please pay attention to Bolt tightening when installing Base.
If you want to close Firmly, the Base will lose and distort.
View detail
![[Repair Parts] Rubber Stopper [Z9571R]](https://img.webike-cdn.net/catalogue/images/91664/17285_01_TS.jpg)
It could be used for OEM Carrier Plate.
I was looking for replacement parts for my Honda OEMCarrier Plate anti-vibration Rubber stopper that had deteriorated and came across this Parts (Replacement Rubber stopper for GIVI M9A/B), which I found to be a collaboration product with GIVI.
It went on the HondaOEMCarrier Plate with no problems at all (at my own risk).
I attached the rubber to the plastic base and then attached it to the carrier plate, but it was quite large and strange to attach the rubber to the plastic base. I had to pull it very hard to get it to fit.
View detail
![[Repair Parts] Inner Bottom Matte [PE43N E43]](https://img.webike-cdn.net/catalogue/images/32552/94990_01_TS.jpg)
Flat cushioning material
The bottom is flattened and the Material is soft, so it replaces cushioning material and is gentle to luggage.
Since the matte capacity is reduced, it can be removed depending on the application.
View detail
![[Repair Parts] Screw Set](https://img.webike-cdn.net/catalogue/12366/65884_1_l_TS.jpg)
Aftermarket parts are very helpful.
Purchased for Repair as Rust came out.
These fine Aftermarket parts are really helpful.
I hope they will continue to do so.
View detail
Easy to use
I installed it on a CT125 and it is large enough to fit one full face. The lock is a little bit hard to do, but I think I will get used to it in time. View detail
Nut mold on the back side sticks
I have been using Tank Lock and wanted to continue to use it.
The installation itself can be done by anyone since all you have to do is tighten the screws.
However, if you leave it on, you may not have to worry about it, but when you replace the air filter for maintenance, for example, you will have to open the tank cover, and you will have to remove this product every time to remove the tank cover.
Then I took it off and found that the Nut on the back of the part that holds the Bag in place was hitting the Center cover and molding it.
The precision of the workmanship may not be good, and when the bracket was applied to the tank cap, it was not bent enough and the bag attachment part was in a floating state.
It is supported by the Rubber foot, but the Rubber foot is not high enough or it is floating, and when the Bag is placed on it and the Rubber foot touches the Center cover, the Nut on the back side touches the Cover.
If you don't think about mold adhesion and maintenance, there is nothing wrong with normal use.
View detail
I like the squares.
I commute to work on my motorcycle, so my first requirement was to be able to store my helmet.
Unlike other MODELs, it is a square design, so there is plenty of room in the SPACE for rain gear, etc., in addition to the Helmet.
It is very convenient to put things bought at SUPER or Convenience!
View detail
![SRV Fitting [SRV-R25]](https://img.webike-cdn.net/catalogue/images/15075/94263_O01_TS.jpg)
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
Use with Fender Eliminator Kit
[How is it used?
I purchased this product to install GIVI's Top case on my MT-25 which I use for long trips and shopping.
There are many options for carriers, but we chose this product because we wanted to attach a GIVI Case and were a little concerned about the strength of the Grab Bar alone.
Was the one you received as per Image?
Bolt and Bracketetc. were included as shown in the pictures without any shortage.
Was the installation difficult?
It takes considerably longer to install than the Carrier with Grab Bar installation.
There is an installation instruction manual, but the Large section is explained in letters, so it was very difficult to understand MinusPoint.
Also, although the kit is not designed to be used in conjunction with the Fender Eliminator Kit, it was possible to install it in conjunction with DAYTONA's Fender Eliminator Kit at my own risk.
There is no interference with the Blinker, although it is necessary to place a 3mm spacer between this product and the Fender Eliminator Kit.
How was your experience with it?
The Tandem Footpeg and the Fender section are fixed in 6 places in total, so they are fixed quite firm.
It is quite stable, with no interference with the vehicle body or chatter.
It made shopping more convenient.
However, due to the fact that it is fixed with a Tandem Footpeg, KIJIMA's Helmet Holder cannot be used together.
[Included Parts:were they on?
All necessary items other than tools such as mounting Bolt, Nut, Bracket, etc. are included in the package.
[Was there anything that disappointed you?
As I mentioned above, the installation instructions are very confusing.
It is not enough to have a diagram like an assembled piece of furniture, even if it is explained in words....
In addition, the size of the cap to be attached to the bolt on the SIDE was not correct, so it was necessary to file it down to a size that would fit.
【Review】
Firmly fixed to the vehicle body, it makes shopping and other activities very convenient.
The holes were well aligned and there was no need for any special modifications afterward.
I would like to see a little more work done on the instructions, as the product was good.
View detail
![Mono-lock Case [E43NTLD]](https://img.webike-cdn.net/catalogue/images/105397/95339_TS.jpg)
easy to use
[How is it used?
I was looking for a Top case in a size that can be used not only for shopping but also for overnight stay to attach to MT-25.
This was the first time for me to purchase a top case, but I chose this product because of its price and size.
Was the one you received as per Image?
I knew it would be huge, but the product that actually arrived was even bigger than I imagined. (Lol)
Was the installation difficult?
It is very good for GIVI's SRVFitting because it can be installed in seconds.
It is easy to install and remove and requires unlocking, so it is very well thought out for both convenience and security.
How was your experience with it?
The loading capacity is perfect.
The square shape allows for quite a lot of stuff to be put in.
A full face helmet can also fit in the vertical orientation, so you don't need to use a helmet holder if your luggage is small. If you do not have much luggage, you do not need to use a helmet holder.
It is also good that the structure is key lock-in-proof, so there is no need to worry about such things.
[Included Parts:were they on?
In addition to the top case, the Mono-lock base and other necessary items for installation are included.
I am using SRVFitting of the same Brand, so I do not need Universal's Mono-lock base in that case.
[Was there anything that disappointed you?
Not particularly
【Review】
It has a sufficient capacity, with key, and is easy to attach and detach.
It made shopping easier.
View detail