Reviews
Both cost-effective and convenient
I had a Socket version of this shape, but it was not tinker-proof, so I purchased this product. The price was just right for those who think that a set of tools in a tool box is enough, but not for those who think that the texture is also an attractive feature of tools. View detail
It's a bit expensive
Purchased for replacement with bremboRCS.
Cospa is not good.
More than that, I would have liked a little more flexibility in Bracket.
It will look and feel different, though.
View detail
Does not become a DucatiOEM pig
The radius size was exact, but the position of the projection on the hand side was not correct, so I used a grinder to cut it off. There were several similar products available from other manufacturers of external products, and I chose this one because of its quality, but I am satisfied with its thick construction. View detail
It's not compatible with my black box
Quality and Texture Information Flat Braces Easy installation of black boxes for your environment Size Chart Information License Plate Size Cost performance and comparison with other products. There are a lot of products, but the products that I thought of WeBike packaging is always great. Arrives in a week for delivery and packaging Purchasing concerns, precautions, or advice It's a shame to only give you black box fastening bolts It certainly doesn't fit other brands' black boxes, but it's definitely fair View detail
Fork Oil Level Adjustment Kit
The accuracy of the syringe and piston is good and there are no air leaks, but the narrow hose requires a lot of force to pull the piston. Since it is impossible to pull the Piston with one hand, you can concentrate on your work by fixing the Gold Pipe on the Fork and making the Fork stand on its own.
Cleaning Hose and Gold Pipe for next time was also time-consuming.
It will take some time to work through the trial and error process, but once you get the hang of it, I think you will be able to proceed quickly and easily.
The Scale engraved on the Gold Pipe is also highly accurate, but it is in 5mm increments, so if it is exclusively for your car, marking it will help you to make progress next time.
View detail
It has attached to WR250R. Isn't it the dress-up effect up?
It has attached to WR250R.
Isn't it the dress-up effect up?
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
Cost-effectiveness is ….
Quality is fine.
Although there are many Chinese copies available in the market, it is good for your mental health because it is made by a reliable manufacturer.
Installation is easy, as all you have to do is shift the Radiator and insert it, but the Edge is sharp, so hand protection is a must.
Radiator's protective effect, of course, has also improved its appearance.
If it were a little cheaper, there would be nothing to say….
View detail
The REBEL250 SEdition came with a Large
I bought this for my REBEL 250 SEdition to attach the FrontCamera drrorecorder to it.
of the same product before purchasing this one. "Φ40-Φ45" I bought the Size, but the Size was just a little short, so I bought this additional one.
As a result, this one was too large.
This is "Φ49-Φ54" So I thought I could make it work, but it seems that the middle Φ47 or so is Just fit.
If you are concerned about installation, etc. "Φ40-Φ45" I've also reviewed the Size, so please check it out.
The Bolt could not be installed there, so I used the Tie Band.
This one is too loose, so I put Seat in between.
I can't decide which is better yet, but I don't think there will be a large change if I buy either size, since it doesn't shake that much.
View detail
It's a bit forced. Crying 。
This is a must have part for brembo installation.
I was not sure if it was Radial Mount or Axial Mount, but Axial is enough because it is OverQuality.
To install, just mount it on the Front fork and assemble the Caliper.
However, Aluminum Cut-out is not the same as "It's just the way it is. The feeling is ……
I think GCraft's Black Anodized Aluminum was more natural. (Sweat) 。
View detail
Maybe not for upright Fork.
I bought this product to install the FrontCamera of Mistuba Sankowa EDR-21Gα, but I tried to install it to the non-moving part of the upright Fork of our vehicle, but I could not find a good position and gave up using this product.
It might be good for Inverted Front Fork.
View detail
Things are normal.
I chose it just because it was cheaper than the DAYTONA as a Camera mounting bracket.
The MiVue M760D from DAYTONA was installed.
The Bracket itself is strong and can be adjusted to slide sideways, so you can adjust the position of the Camera to fit your Motorcycle.
The angle was apparently level and the thing was a good product.
The following will be about compatibility.
After I installed it, I noticed that it was confirmed that Mistuba Sankowa and KIJIMA, which are basically used to secure Camera with Bolt, were compatible, but DAYTONA was not. (You don't notice it, right?)
The MiVue M760D's Camera is fixed with Double-sided Tape and In-Hemp palm mack, so it can only be attached with Double-sided Tape, and the In-Hemp palm mack could not be tightened because the seat surface is not square and could not be stopped. (Only the front side can be tightened if it wraps forcibly)
It is possible to use Double-sided Tape alone as it is not likely to cause any problems.
However, it is not a good match because the seat is long on the side and you can see the Bolt hole.
The color is Black, so it's hard to tell if you don't care, but if you are looking for perfection or are concerned about it, you shouldn't choose to install the MiVue M760D.
View detail
pre-cooking
I bought this because the Cook on the Tank no longer closes tightly.
The original cooker should be replaced or repaired, but I didn't have time, so I installed it as an emergency measure.
At any rate, it is convenient to have 1pc.
View detail
brembo installation
This is for the brembo brake.
The shape is good, but it interferes as it is, so I installed a part to shift 20mm from the original position, and finally I was able to install it without interference.
It would have been nice if the Tank fixed Bolt was also Black, but I had no choice but to paint the Screw Black to make it less noticeable.
I wish the selling price was a little lower.
View detail
as one would expect
Well, it's just as I saw it, isn't it?
I think that I can put most Camera on the large size of the base of Camera if there is this much.
View detail
Fits: HONDA CBR250R [MC41]., HONDA 400X [NC47]., HONDA CB250F(14-15), HONDA CB250F(14-15)
Divert to other cars
The car model is different, but I tried to put it on for a change after considering the shape and other factors.
As a result, I managed to get it on.
However, there is one screw hole that does not fit, so it is fixed at 2 points instead of 3 bolts.
Because of Bag Support, I think that Large is sturdy because I think that the load does not apply directly to Large.
It's firmly in place.
The downside is that the price is too high.
View detail
Aiming to increase the cooling effect.
This is an exchange from the OEM 1.1kg. As for the product in question, because 1.3kg and the Compression value only went up slightly, it was the effect of the feeling degree as for the experience. It may be more effective in terms of raising the cooling effect to replace it with Coolant which cools more than that.
The other thing I was surprisingly happy about was that it was easier to turn it around than the OEM.
View detail
I wouldn't recommend it
Since the Zipper only works in the direction of loosening, it expands when it is tightened, the Cup-style Filter wrench is much easier to use
Also, the Zipper slipped when I loosened it and I had to remove it while holding it down by hand
View detail
Fits: HONDA CBR250R [MC41]., HONDA 400X [NC47]., HONDA CB250F(14-15), HONDA CB250F(14-15)
Note on Compatible Car Models
The CBR250R and CBR650F's Rear Footpegs were similar in shape, so they were probably attached I bought it because I thought I would be able to
However, although there is a screw stop between the footpeg and the frame, the Heel I couldn't install it properly because the size of the Guard didn't fit at all
View detail
Wonder
We updated GSXR, recently Radiator's HoseLine, and then introduced a high pressure radiator cap.
However, at OEM 1. It was 1, so it seems that it is originally high pressure to some extent.
Although it can not be realized to the extent of the effect, when examining variously after installation, it seems that both pros and cons are unexpected.
First of all, since it will be high pressure at all times, it will be much more burdensome to the cooling Line. Furthermore, it does not increase the cooling performance of the Radiator, but when the temperature rises, the Coolant boils and vaporizes (Cavitation) It seems that it seems to prevent it from happening, it is quite questionable if we consider whether it will be in a state of high turning rotation as it travels marginally like a regular like a circuit like a regular urban ride, Touring, Pass traveling degree ...
If the water temperature goes up in the first place, the fan turns and the water temperature goes down. But this product is to prevent Cavitation when it gets hot enough not to be lowered by the fans, that is, in a situation such as Circuit etc. which keeps turning all the way. Moreover, in case of running in Race, since maintenance is performed once every time, the burden on cooling line should naturally be considered and maintained.
Although it does not check every time by taking care of the cooling Line so far in public road traveling, how is it always burdening the burden ...
Instruction Manual Although we are claiming that the cooling performance is up! ... I do not think the cooling performance will increase, I wonder, very much.
View detail
Replace from OEM
`Coolant exchange of 01ZrX1200R, simultaneous exchange
If I do not notice it has not been changed for about 7 or 8 years - -
As Packing's Downs was seen before exchange, I wonder if I could exchange it.
Engine is NORMAL and cooling is also NORMAL, so if the same pressure as OEM is enough.
If the same performance as OEM, this one is a bit cheaper.
In the case of ZrX, Cap is below the Tank so it will not be visible.
View detail