Reviews
I would like it to be attached to Rim stripe if possible.
We have applied MDF rim stripe to several (5+) vehicles in the past.
I had to replace my car for the first time in 9 months, and when I tried to apply Rim stripe, I could not find a special Gauge to apply it, so I had to order it again from webike.
I purchased a 6mm width rim stripe and was able to install it without any problem using Gauge, but I would like to see it included or packaged with the rim stripe if possible.
I would also like to see 8mm and 10mm affixed Gauge produced.
View detail
If the Rim width fits, ◎
Depending on the Rim width, there may be a bias, so the center position may be gapped. However, it is easy to apply and mistakes are not likely to occur. If you are a first time user of rim tape, you may want to buy it, but if you are a second time user, you can use FreeHand without a guide. View detail
Attached to Ducati SCRAMBLER
I bought this to attach Rim stripe to my newly purchased DucatiSCRAMBLER.
Size is 17&18-inches Color to match the car body color:YellowSingle Body 10mm width was chosen.
I wanted to start pasting immediately, but I don't know which wheel to paste the 18 separate tapes on.
There is no mention of this in the Instruction Manual.
Are the top 8 sheets in the front FOR 18-inches or FOR 17-inches?
Are the two spare sheets the last two on the front or the back?
Are you asking me to paste it in the right way?
As a matter of urgency, I inquired through MDF's Home page.
I have not received a reply yet so I am unable to paste it.
View detail
Rim sticker
Easy to put up.
It sticks well.
Quite sturdy.
View detail
Vulgarly gaudy
First of all, it is expensive.
Combined with the color of the Wheel, it became vulgarly gaudy. Also, the Rim was pear-shaped and peeled right off.
Adhesion appears to be weak.
View detail
No need.
Bend the product to make it look like a Rim, but use it as such.
I didn't feel the need to do so.
The point is, if you can make a nice circular shape, you can do it by hand.
I used the circular marks in Rim as a guide when pasting.
I was able to apply it by hand.
It might be useful to have such a landmark, since it should not exist in normal Rim.
However, it is a product of Level that may.
There are two types, one for 4 and 6mm and one for 10mm, so be careful when purchasing.
If you don't like to put it on, it's not expensive and you should buy it.
View detail
It's a little plain.
It was easy and clean to apply. I don't know how durable it is yet. The color was a little plain. View detail
The imeChain effect is outstanding.
The color choice is important because it changes the whole atmosphere. 6mm is better than 10mm for GSX1300R HAYABUSA. View detail
thin
It's not suitable for CourseYouth/Race use. View detail
Design is nice, but …
Quantity:1 Set is all Quantity:It was a 1pc. seat, and it seemed very difficult to do, so we divided it into 16 parts per pc I did
I think this was a Large correct answer
It's easy to work with the Divided and Applied Gauge
The design is perfect, but the overlap is a bit annoying I'm also wondering if each one is expensive
View detail
not quite
There is not much cutting on the seal, so it is still in place where the Cowl is I was able to put it on some Parts by myself because I couldn't put it on the first time View detail
I think it's a good Ideas product
When you apply the Rim stripe while the Wheel is still attached to the body of the car, it is very easy to use I think I removed the Wheel and stuck it on, so I sprayed enough soapy water on it and stuck it on by hand It was easier to put it on However, I'm sure it varies from person to person, so the price is so cheap that you can buy it as insurance Maybe it's good View detail
It was useless..
I do not know in other Size, it was useless for 12-inches.
Seal is solid, so 12-inches it is not difficult at all to paste by hand normally.
View detail
Is it impossible for Off-road motorcycle?
I tried wearing it immediately after arrival It was very thin and it seemed easy to stretch Design was so so so
Adhesive power is very weak as decals are peeled off the backing Sticky which I had with fingers has already disappeared Even if you revive with Dryer you can peel off as you trace from above It seems easy to peel but peels off even in the wind while driving is. Especially for off cars there are a lot of Timing to wash, so I think that it is impossible for an off car. It was unhappy's happiness not to purchase with Full set.
At the same time I purchase Decal of FX at Rear This is also sticky and strong, it is thick and easy to stretch It seems to prevent scratches etc. I understood simultaneously the difference as it was replaced at the same time. I think that Front will make his own.
View detail
Gold Wheel to GoldPlating Rim tape
Honda's GoldWheel is a little tasty so add Rim tape as Accent.
Infinite Spec. Think of the colors of RedRim and Others as you would like to add color to Paint in the car image
Purchase a Plating dare to compare GoldWheel and try to buy a little expensive.
Unlike ordinary White and Red like Type, Plating type has a thin Tape.
Since the back is Silver's Tape, the adhesion is also weak. Even if it is degreased and pasted it will be stuck again
I worry a bit about I can do it. Inversely speaking it was easy to paste. Without Guide.
But durability is A little worry. I expect it in the future
But well Major Parenthesis I wonder if I am getting better!
View detail
It is easy to have
I bought it together to paste Rim stripe. It is chatty than I thought.
It cracked on the way and reinforced with SEROWTape. But I think that it is easier and shorter to buy it because it is cheap.
View detail
Individual difference?
In Imechen to RMX 250 S.
Hang Paste while warming with Hair dryer with decal easy to stick. Because the heat of Hair dryer is enough, it is likely to burn if it warms any further.
Due to individual differences in vehicles or because they are disassembling a number of times, the Decal lines of each part are not aligned. Paste each Parts and install it and do not align the Line Graphic will be gapped.
Just obviously there are many places where Gap and the black part of the black are left in the White part and the affixability of Decal itself is contrary. Since it is domestic production, I want the accuracy improvement.
Number Plate and others that seems to be having difficulties have been broken and it was possible to stick without much effort with making it fancy - - - -
Decal Thickness is thinner than I thought, Protection effect can not be expected. It is influenced by the base for Material with good thinness and elongation. Since unevenness and Garbage etc. stand out firmly on the surface firmly enough pasting is necessary to be beautiful enough.
I understand what I would like to promote, but after a while MDF's Logo. In SIDE "FreeRoad model" Logo of.
I understand the feeling, but I little embarrassed so I'm going to put a sticker on each logo...
For degreasing industrial use (For fuel) Recommendation for Alcohol. You can purchase at Homsen. Brakes cleaner hurts resin and hastens deterioration.
View detail
Used to paste Rim sticker
I used it because I can stick it beautifully to paste the company's Rim sticker.
At first I was not able to grasp how to use, but as I got used to it I got to be able to stick cleanly.
Tire When sticking paste Weight on the end of Rim, this Gauge will get caught in that part, so that only that part will suffer.
Product itself is Material : Because it is Plastic, if you keep it, it seems to be available for next Rim sticker pasting.
It is true that the resin of the free plastic is out of stock, so it seems reasonable about half price is reasonable.
View detail
It is easy to use because it is exclusive ...
As expected It was possible to attach to Smooth when using!
However, it struck a rash hour, broke apart and became useless.
Perhaps it can be hand-pasted unexpectedly.
View detail
Rim stripe for pasting
Although it is not for the exclusive StripeSeal, I tried using it for pasting. I could not stick it successfully. Maybe because I am clumsy. View detail