Reviews
Not JAPAN, but acceptable
Used for CUB.
Since it is not JAPAN, the accuracy is not as good as it could be.
Motorcycle that runs as slow as a CUB could use it.
Give up on the flares because they are less than 1mm in length and width even if you do your best to adjust them.
View detail
Fits: HONDA GROM, HONDA MONKEY125, HONDA CBR125R, HONDA CROSSCUB110, HONDA NSF100, HONDA SUPER CUB110, HONDA XR100MOTARD, HONDA CRF100F, HONDA APE 50, HONDA APE 100, HONDA XR50 MOTARD, HONDA CD-based Engine, HONDA CUB System Engine, HONDA GORILLA System Engine, HONDA MONKEY Engine
with MagnetDrain bolt
Drain bolt with Magnet
I wanted to change it and bought the cheapest one I could find.
It arrived right after the Oil exchange, so it has not been used yet.
It's going to be a while before I can get to it.
Aluminum texture is good.
View detail
Fits: HONDA GROM, HONDA MONKEY125, HONDA CBR125R, HONDA CROSSCUB110, HONDA NSF100, HONDA SUPER CUB110, HONDA XR100MOTARD, HONDA CRF100F, HONDA APE 50, HONDA APE 100, HONDA XR50 MOTARD, HONDA CD-based Engine, HONDA CUB System Engine, HONDA GORILLA System Engine, HONDA MONKEY Engine
It's faster to buy.
This is a type of Drain bolt which has a Wiring hole from the beginning.
I bought it because I needed it for regulation when I wanted to race with CUB.
Drain bolt itself is Material:Aluminum with Magnet inside.
Personally, I was happy with the same iron as the OEM, but it was a bit odd to drill the holes on my own with a Drill.
I think it's faster to purchase. The price is cheap, too.
View detail
Fits: HONDA Super Cub DX, HONDA little cub, HONDA Super Cub STD, HONDA press cub, HONDA Super Cub DX, HONDA little cub, HONDA Super Cub STD, HONDA press cub
It is slightly long.
I use it for my LITTLE CUB.
There is a difficulty in fitting. Because it is a little long, the grip end part is left over.
The Switch box cannot be moved, so it cannot be used as a countermeasure.
View detail
Do you like the color Orange? Amber.
What is Amber? At first I thought, "What is Amber?", but this time I bought it and used it.
Orange color is a good color, so I was satisfied with the color.
View detail
It glows well!
I replaced the Valve as soon as possible.
It's a bit of a blur.
View detail
A little hard
It is harder than other companies of the same type.
Some people like stiffness, so it may be good for those who like it.
I would rather have been a bit more soft.
View detail
Fashion oriented fashion oriented fashion model
Since there was a request to make Grom's feet good, I planned drastic Lowdown.
Grom 's Rear suspension is not a LINK expression, so Lowdown is difficult. Shock itself Short itself or use this Parts.
At first, I tried to shorten Shock itself, but Stroke would be reduced, and I decided to install this product from the Cost side.
There are no Instruction Manual for goods delivered from Wee Big. Although I never can not afford it, I think that it is better to have Instruction Manual as well.
Quickly install. Trouble occurred when attaching Base to Swingarm. Swingarm hole and base hole position are off by Comma several millimeters and Bolt does not pass.
Since there is no choice, I will scrape away the base Aluminum material. I think there is a problem with the product accuracy of Grom rather than the accuracy of the product. Grom's product precision is quite about.
Finally I aligned the holes, so when I try to install the Shock, I will not attach it.
Like OEMShock, if the Damper diameter is thin, my Grom is a vehicle height adjustment expression of Mukawa river and the body is thick. Since it can not be helped, I managed to remove both Damper Body and Mounting Base and managed to install it. Temporarily assembled and scraped repeatedly, so I took horrific time to process Aluminum material.
I finally installed it, but this time it interferes with Tire, so I was able to shave this shock attachment part as well and set it as OEM level finally.
Impression after installation. Certainly the vehicle height drops. Get down. Although the feetability was improved, lowering the Front side can be done by shifting the mounting position of the Fork, even at the maximum Large 1. Only about 5 cm does not go down.
That's why I fell backwards and my appearance is bad. In order to lower Front, we have to put our hands in Fork itself. Also, since the point of action comes behind, Shock became hard as expected and the ride comfort became considerably worse.
Because it is this state in the Shock of Takekawa that is setting softly, if it is originally a hard OEMShock, more comfort will be exacerbated.
If OEMShock is a combination of glomes with good work accuracy, it will be attached with Bolt - on, but otherwise it will be hard to install.
Also, it is accompanied by deterioration of ride comfort.
Considering the unbalance with the Front side, it is not that Lowdown is completed only by installing this Parts.
View detail
Mirror installation of KSR 110PRO
The acquaintance attached Mirror under Handlebar is often Parenthesis, purchase, part cut part is obviously wanted to imitate, but impression that there is no part that cuts hands such as BALI and it is not bad despite price was.
After actually installing it, I closed the Screw in the place where the Handlebar was bent, and it cracked quite easily. My mistake I did not put on the straight side of Pipe.
I finally got it like the picture below. The degree of freedom of installation is high, I think that not only Mirror but also various ways of using it are cheap.
View detail
I made Bar handle, so I tried it
I bought it for the bar handle of ZX - 14R.
We, the product of this hand is the first time, performance More than anything else,
"I am also using MOTOGP. "
I am interested in things called '
I bought it in a Dress-up mood.
The thing itself is Green Light which is somewhat brighter than Green Light of ZX-14R, as shown in the picture.
Installation is - - -
Instruction Manual was not attached. (TΔT)
I thought that Bolt was in Anchor and it would be better to close it,
I do not understand the meaning of the Spenser in the Grip end part,
Quantity : 1 Set of 2pc. Is it? Quantity : 1pc. Is it?
Do you fit in with shape problems?
Is it just a lid?
I do not understand well, first of all,
"I got it like this. "is (Lol)
Although the angle of the Guard bar seems to change,
After tightening, it turned inwards and was fixed,
Which stage do you open and fix?
I want to see it..
In terms of things, I think that it is not so bad,
Oh yeah, it is not a thing you are attaching,
No one can hear it (Lol)
I want you to enclose even things that describe simple installation methods.
Mounting method, beforehand, similar products etc.. It's better to check the ones with hompe or blog
View detail