Reviews
Repair parts were available for purchase!
I had given up on it because it was an overseas product, but I happened to be looking at it and found it and ordered it immediately. View detail
Fits: Others
Processing is required, but it's cheap, so it's good!
I was looking for a cheap hand guard that is not Solidly's CloseHand guard, and I found this one.
Parenthesis is ◎! Off car for cosmetics for the price, it deepens the taste of the car.
As for durability "It cracks easily." However, it is good if the handlebar can be made to tilt while at the same time serving as a bush guard at least.
The mounting holes on the One Side are incredibly gapped, and I couldn't help but think that they are cheap and accurate, but that's okay because they are cheap.
View detail
The look was to my liking.
I like the way it looks, but the bulbs are EURO bulbs, so the number of bulbs that can be changed to LEDs is very limited.
In addition, the Headlight terminal is a Hira terminal, so the Wiring and terminal must be provided, and since there is no Cutline, it may not be possible to drive on public roads.
View detail
It is a little small, so you may need to be careful depending on the type of car.
[How is it used?
I found this product when I was looking for a new light cowl because the vehicle light I had received was a battered Other Brand Product.
I purchased this product in the hope that it would moderately mask the Harness and Meter around the Light in the Front section.
Was the one you received as per Image?
It was a little smaller than I had imagined, and I felt that it was not suitable for my purpose of use. It was a little smaller than I had imagined.
How was your experience with it?
When actually installed, the overall size of the light was too small to fully hide the electric wiring that would collect around the light, and the dimensions above the light were too short to expose the Speedometer, resulting in an overall appearance of poor balance.
The design itself is a good parenthesis, so I think it would be a good fit for cars equipped with compact digital meters these days.
[Points to note]
It is difficult to grasp the overall size of the product unless you see the actual product or see a picture of the product installed on a vehicle.
The design seen from the front is intrepid and Parenthesis is good, but it is a flat design, so when you look at it from the side, it looks like... what is it? It is a flat design, so when you look at it from the side, it looks like... what?
How did it compare to other products?
The design is not inferior to other companies' products, it depends on the vehicle and the installer's Sense (my installation of Sense was incompatible with the vehicle in which I installed it).
Other items that would be helpful
Point and hang of installation
Elastic band and material for mounting:Two types of side stays for plastic installation and bolt & lock nuts are included in the package, so you can install them with your sense of parenthesis.
[ITEMS TO BUY TOGETHER
The H4 head lamp bulbs that are initially installed are not very bright. You may want to consider brighter H4 bulbs or LED Lamps.
[Opinions and requests to Manufacturer
I replaced the reflector in the Lens with an LED position bulb, and the progress stopped, but I would like to see better thermal countermeasures.
View detail
In use on KLX230
KLX230 (SE) I bought it in Design, although it is being used for
The functionality of the car is honestly very dark, and I'm not sure if it can be used on public roads, since the street lights are brighter and there is no cutline. ()
As for the feel of the product, it's just cool w
There are three Wiring itself, Black Wiring is Earth?
If you match with the general Wiring color, the high and low will be reversed, so it is better to confirm the intention of the bulb you want to light before assembling in advance.
I lowerQuantity at the time of low:2pc. The Set is lit, the high switch is On, and the top bulb is also lit.
The body is assembled with elastic band on the lower side only, but it is too long and loose for the upright suspension. The inner tube of KLX230 is m37, so I think it is the right size for the inverted suspension. The upper part of the bracket is made by purchasing a bracket at Home center and drilling a hole in the plastic part where the Elastic band is attached and screwing it in place. 。
There is also an interference point where the brake hose hits the side of the hose, so I used a design knife and a nipper to cut the hose diagonally upward to alleviate the interference.
View detail
Consumables?
I don't remember how many years after I bought it, but I got rid of it after about 3 or 4 years of use. It might be revived with a good Chemical, but the gap under the Headlight also bothers me, and the reason is that the OEM Product seemed to be of better quality than anything else. Durability. View detail
Fits: HUSQVARNA TE250, HUSQVARNA TE125, HUSQVARNA TC125, HUSQVARNA FE450, HUSQVARNA FE350, HUSQVARNA FE250, HUSQVARNA FC450, HUSQVARNA FC350, HUSQVARNA FC250
Mounted on TE250
I always ride HUSQVARNA's TE250 for forest road touring and hill climbing.
After about a year of use, the exterior of the car was getting worn out and the fork guard was getting cracks. I tried to order the OEM exterior, but it was very expensive. I tried to order OEM exterior but it was very expensive.
Now I can ride my motorcycle in Paris for another year.
View detail
Fits: HUSQVARNA FE250, HUSQVARNA FE350, HUSQVARNA FE450, HUSQVARNA TE150, HUSQVARNA TE250, HUSQVARNA TE300, HUSQVARNA TX125
Exterior Set Replacement
I always play with Enduro and Hill climb in the forest road touring and course.
Especially on hill climbs, you'll be turning your motorcycle over and dragging it around, which can quickly hurt your bike. Especially the exterior.
It's been about a year since I started riding, and the shroud is cracked and the side cover is damaged, so I replaced it.
I was able to install the Bolt On securely.
This kind of Kit is called Quantity:It was sold in Set, and I changed it cheaply, so it was very helpful.
View detail
To MOTARD.
I bought it to install on my WR250X, but I am not using it at the moment because it was different from Image when I installed it.
Well, I think it's a matter of taste.
View detail
Fits: YAMAHA YZ 450F, YAMAHA YZ 250F, YAMAHA WR 450F
I'm not sure it's functional.
Protection is no problem. 。 It's a two-piece structure, and I like it because it's simpler than other manufacturers' products.
There is no damage that becomes impossible to run even if it hits, and I think that it is difficult to give stress to the attachment part of the Swing Arm.
However, the decrease is early! I think that it is too early even if Repair Parts comes out however.
It is a pity that it seems to take longer than expected when it is also out of stock.
View detail
Fits: YAMAHA YZ 125, YAMAHA YZ 250, YAMAHA YZ 450F, YAMAHA YZ 250F, YAMAHA YZ 250FX
Cost-effective
I bought it to remove the Headlight when attending Events because it was inexpensive.
The cosmetics are quite good and are great for Custom and diversions.
Comparison products
I chose this product because I liked the shape.
https://www.webike.net/sd/24170982/
View detail
Fits: Others
Recommendation for those who can cut and shave.
The car is a CRF250M and the Handlebar is used for ZETA's CX Handlebar.
It is not the same as the Hand guard with a frame, but it is not the same as the FirmlyGuard! However, it protects your fist from the wind and small stones. The area is small, but the way your hands get cold in winter is somewhat better than the No Guard. It is somewhat better than NoGuard in winter.
Because this is a universal product, it may take some time to install it. The installation method is quite simple, so there is no problem.
In the case of my CRF, Clutch Side was able to be installed easily. As for Brake Side, the throttle wire interfered with the product image, if you compare the photograph and the product image, you will understand, but I shaved a "mountain".
I made it easy with Grinder, but the Material is so soft that I think I can get away with hand saws and File.
By installing it, you can get more volume in the car and the off-road feel is much better.
The price is low, and it can be installed with a little effort. The color is also available in each manufacturer's image color, and it is recommended.
View detail
Everything fits.
POLISPORT has a lot of universal products, but I think they have a line up of products that are easy to match with any car.
It's also very cost effective, which is handy for the fragile Off-road exterior.
View detail
High cost performance
I bought the POLISPORT Poly sportsFork Boots because I needed them for this occasion.
I think the quality of the product is reasonable for the price range
It's safe to say that you won't be disappointed by the amount of gold you buy, which is Large
The quality of the product itself is guaranteed to some extent, so if anyone is struggling with it, you might want to pick it up.
View detail
I don't know what the price is.
I bought it to play Off. I'm a novice.
I bought it, but I have to admit, I'm not sure if this is a good quality for the price.
I bought this because I've had a knee injury before and wanted to guard it there.
For that matter, it's Simple, but it's OK because they will protect you.
But I would like to see a bit more of a luxury feel to it, as each piece of Parts is so light.
View detail
How durable is it?
It is Elastic band which seems to be weak against ultraviolet rays, but I bought it because I thought that availability is high because it is Rubber.
It is a good choice for retrofitting a road motorcycle with a Bikini Cowl and it is a very nice floating mount. I think it is necessary to change it periodically, but if the weight of the cowl is not so heavy, it is enough to use it.
If you do it well, you won't need to make a complicated bracket, which is why I recommend it.
View detail
OEM Equivalent Product
I bought a used CRF250R with a cracked Rear Fender, so Poly I bought the one made by SPORTS
System or Quantity of mounting holes:Pair (for Left and Right) I was personally satisfied with the product, as there was no distortion of
View detail
Fits: HONDA CR 125R, HONDA CR 250R, HONDA CRF 250R, HONDA CRF 450R
OEM Equivalent Product
The Number Seal on my used CRF250R was cracked, so I bought a Poly I bought the one made by SPORTS
I was personally satisfied with the accuracy and distortion of the mounting holes, and there was nothing to worry about
View detail
Fits: KTM XC, KTM XC-W, KTM XCF-W, HUSQVARNA fe, HUSQVARNA FC, HUSABERG fe, HUSABERG TE, HUSQVARNA TC, HUSQVARNA TE, KTM EXC, KTM EXC-F, KTM SXF, KTM SX, KTM XC-F
The price is cheap
If it is Disk guard of other manufacturers, the dedicated Bracket is needed separately, and the price is not so bad It's a good idea to install the disk guard on the BottomFork Protector In this case, I installed the disk guard on BottomFork Protector Because of the cheap price, it is not so easy to make, but I could install it without any problem However, there is a place where the collar is short I thought I may have misapplied the color, but it's not so
View detail
Fits: KTM EXC 125, KTM EXC 200, KTM SX 125, KTM SX 200, KTM XC 125, KTM XC 200, KTM XC-W 125, KTM XC-W 200
Satisfied
The RearBrake pedal seems to hit the Clutch cover in the fall I found this product when I was looking for it Now I can attack with confidence View detail