Reviews
Emon quality for peace of mind!
I have been using the one in Emon's Terminal set, but I ran out of stock, so I purchased this to replenish my supply.
It is essential for electrical DIY. Emon quality for peace of mind!
I bought it at an actual store (mass retailer), but Webike was cheaper. Next time, I will buy it before I let it run out, or adjust the shipping cost, or whatever.
View detail
Sometimes Ladder rail, sometimes BedExtender.
[How is it used?
Used on Hilux to carry Enduro racer.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When loading and unloading Motorcycle, it can be used as a Ladder rail, but sturdiness is not a problem. It can also be used as a BedExtender to prevent cargo from falling off the bed when transporting, and is also safe on highways without loosening.
[Points to note]
Be careful not to put on the included Ratchet as described or it will loosen.
How did it compare to other products?
I really recommend it because there are no other products similar to it. It looks cool and I have no complaints.
View detail
It is convenient to shorten Wiring because Sleeve can be inserted later.
The Bullet Type Terminal of this rear-entry SleeveType is useful to make effective use of the narrow space under the Seat of the Motorcycle.
This is a great product for places where you need to do several Wiring.
View detail
Fits: Others NISSAN CaravanNV350, Others TOYOTA High ace200 series
Space would be a bit wasted.
I use it on my Narrow High Ace van. I bought the additional type for the Rear Sets because the full size motorcycle could not fit on the Rear Sets unless it was stacked diagonally.
With Rear Sets that can be shifted in front of SUPERgl, it would probably go straight in even without DirectKit.
View detail
Fits: Others High ace, Others Radius ace, その他 Regis Ace, その他 Hiace
CARMATE Drink Table
Item well received.Nice fitment and good quality. Easy installation and very firm with double sided tape attached. Love it. View detail
Fits: Others 200 Series High ace Type 4
LEGANCE panel
Very nice packing. Well protected. Item is very nice and fitment is great. Giving another level of look. Loving it. My second order on this item. View detail
just right
I purchased this product to store my CB250R in Container.
Since the step difference was 20 cm, we decided on 1200mm because we thought it didn't have to be that long.
It can be stored without such difficulty, although it is necessary to push it forward with a little momentum to store it.
I was worried that it might gap, but the claw part is very good and stable.
It folds up beautifully and is a good buy.
View detail
Wiring processing is indispensable! LOL!
[Purchased for.
I purchased the Blinker Wiring to match the HONDA project because I switched to Active's Other Brand ProductBlinker.
Impressions of use
I will not introduce the method of attachment here, as I am sure you can find many simple methods on the web.
The size was just right and easy to use.
I've had the blinker on for about 6 months now with no problems, so if you change the Other Brand ProductBlinker, it may be a pain in the ass, but please give it a try! LOL!
By the way, this can be done without special tools, so if you only have thin pliers, you can do it, so give it a try! LOL!
【Review】
Just one word! I mean, I can't start without it lol.
View detail
BOXYSTYLE steering
Package arrived nicely. Steering wheel gives a very nice grip and the workmanship is very good. Feels good and flat bottom indeed is better access in and out. View detail
Sounds great! I knew it "LexusOEM"
Installed on a high ace6 Diesel car.
It seems that many people change Horn of High Ace to Lexus Horn, and it has become a standard custom.
Beep." from the sound of Fern." The sound was a very resonant sound.
Incidentally, it seems that Estima and others have also adopted this nice-sounding Horn. Around that area Lexus." I feel that I am on the shoulders of the Brand called
certainly EstimaHorn." Than Lexus Horn. I think I'm more likely to buy a… It was a bit of a Small story.
Now, I personally felt that the installation SuKill was a little high.
I don't know about the other models, but for the 6 high ace, it was necessary to remove the front grill and bumper in their entirety.
In my case, I had already installed an external front lip spoiler, so I had to remove it as well.
There are quite a few Bolts and Fasteners attached to various places, so it takes time to figure out how to remove which one, which Coupler to remove, etc.
However, as I mentioned earlier, the Horn replacement for High ace is Standard Custom This is the case. Therefore, if you look up how to do it on the Net, you will always find a teacher, so refer to his/her blog.
It took me about an hour and a half to put it back together after removing the Bumper? It took me about 1.5 hours from the time I removed the Bumper to the time I put it back on.
We estimated the work to take about two hours. That went faster than I thought it would." I was under the impression that it was a task I would not want to do if I had to do it again…
View detail
It is light and easy to use, but...
It is light and easy to handle. However, when used near its load-bearing capacity, the black plastic part and the aluminum frame began to bend. Although it has not broken yet, it is recommended to use it with a margin for weight. View detail
It is large, so it takes up a lot of space, but it is a good product!
[How is it used?
We purchased the Grounding Wire to add to the growing number of electrical components such as the Oil Temperature Meter and USB power supply.
Was the one you received as per Image?
In the case of Blinker's Grounding Wire, HURRICANE's Grounding Wire is less noticeable because its outer diameter is smaller than Blinker's Grounding Wire, even though its inner diameter is 10mm.
Was the installation difficult?
If you have Electric Works Pliers, you can process without problems, but if you don't have them on hand, processing will be tough.
How was your experience with it?
The Earth was removed well. The original one I used was thin and unreliable, so this one feels secure.
[Included Parts:were they on?
In addition to the terminal, Material:It has a Rubber Wiring Cover.
[Was there anything that disappointed you?
Nothing in particular, but the outer diameter is large, so you may have to choose where to use it.
▼It can be used to make your own Extra Grounding wire, but the Package description also seems to support power extraction from the Battery.
View detail
Fits: Others High ace, Others Radius ace, その他 Regis Ace, その他 Hiace
CARMATE Drink Holder
Packaging is very well packed! Always so neat and nice. Product is well designed and fit well on the console. Box also comes with installation illustration. Happy again with Webike. View detail
Nice slip mat
Packaging is neatly pack. Item is well delivered in conditions. Slip mat size is exactly nice to fit into the console. Nice cutting and we'll design. View detail
First time purchase
I found out that there was a larger standard than the one I usually use, so I bought one to try it out.
It is impressive that the use of Cover is different from the Small Saiban standard.
The cover is well made, and its waterproof and dustproof properties seem to be better than the smallest standard.
View detail
Purchase shortage
Purchased for parts replenishment.
I think it is good and affordable.
I thought the quality was normal, so that's why the number of stars for that Image.
View detail
also
The quintessential quality of the production.
Some say the price is too high.
The product will convince you.
View detail
-- DRC:hybrid lamp straight type product number: -- D36-41-115 merchandise-information goods details size: -- 20 cm x 150-cm withstand load restrictions: -- it is the lightweight loading ramp borne by the way of thinking new 210 kg. With the combinati
-- DRC:hybrid lamp straight type product number: -- D36-41-115 merchandise-information goods details size: -- 20 cm x 150-cm withstand load restrictions: -- it is the lightweight loading ramp borne by the way of thinking new 210 kg.
With the combination of the resin panel developed by new technique, and an aluminum extruded material, it succeeded in the weight saving from the conventional loading ramp made from aluminum.
The withstand load engine performance of a resin panel is enough, and it can bear the weight of an off-road motorcycle calmly.
With the form of the design only for a motorcycle, it is proud of preeminent sense of stability.
The rubber is stuck on the flesh side of the plate hung on a transporter, and a transporter is not damaged.
The best size can be chosen as its transporter by abundant size deployment.
View detail
Made by Taiheiyo Seiko
Since my motorcycle has been in production for 10 years, I decided to replace the fuse, which is also a consumable part, to refresh it. I thought that a very cheap fuse would be OK, but I was worried about the reliability, so I decided to buy one made by Emon.
The Fuse is not manufactured by Emon itself, but is sold by Emon from Pacific Seiko. Since it is the same product, you can use it with peace of mind.
EmonFuse can be easily purchased at car shops and home centers, but the smallest Ampere is from 5A, so there is no 1A or 3A smallest Fuse in the lineup. Therefore, if you want to purchase EmonFuse, you will have to buy it separately, which is a little troublesome.
You can buy fuses at OEM Parts, but the unit price per pc. is high, so EmonFuse is more economical. However, whether you can feel the difference is another matter.
View detail
Just the right length for MINI, etc.
Just the right length to load in a light van without folding it up
Ideal for Mini bike
Might the gradient be steeper and harder to pack in a 250ccClass?
View detail