Reviews
To prevent slipping when driving or breaking
What made you decide to buy?
For preventing scratches on the ZX-6R tank and for preventing slippage when driving or breaking!
How was your experience with it?
I bought this Volcano Type, and the explanation says that it is suitable from Winding to street riding. When I actually used it, I thought... If I tried to grip my knee after sticking the Tracktion Pad to the Tank on ZX-6R... I actually became around the bottom than the position where I stuck the Tracktion Pad (sweat). I think that it is good to confirm the place where it hits when I do the knee grip because there is a small size pad attached.
About the installation ... It is Clear type that I bought. In StompGrill Preview, there was a recommendation for Black type because the air bubbles are noticeable due to the lack of air venting at the time of installation. After all, I thought that it was uncomfortable to block the beautiful Kawasaki Lime color, and bought Clear type. I was able to study the method of sticking beautifully on YouTube before sticking Stomp Grip and to enforce it safely and beautifully without the remainder of Air. It is the thing that I take time slowly, and stick it while pulling out Air while tapping with a finger from the edge. Black seems to be recommended for the person who is uneasy as there is in the Review of other people.
View detail
worst case scenario
Brown lint? There was something like brown lint?
I realized that after I put it up.
I put it up with a lot of enthusiasm after positioning it.
I don't buy the Stomp Grip.
View detail
Without it.
Repeat Purchase
You can run without it, but once you use it, you'll need it.
It slips and the Form is not set.
A little hang is needed in terms of installation work.
Remove the base paper a little at a time. While scraping, make sure there are no air bubbles.
You need to put up A little each A little each.
If you apply it patiently, it will not contain any air bubbles and will be beautifully finished.
I think it's better if the temperature is around 20 degrees Celsius.
I think it is hard and difficult to stick when the temperature is low.
I`ve omitted the part about putting it on the Frame.
View detail
Excellent ride stability:!!!!
Great ride stability!
I always put the Tank Pad from Stomp Grip on the Tank.
I originally did Circuit driving and Race, and I've been using this product since then.
It's perfect for circuit riding, of course, but it's also perfect for stopping the motorcycle when you're out on the town or touring with a brake, and it stops the motorcycle firmly and safely.
I want you to use it only for everyday riding.
I think the look and feel of the race ish is good because of the way it looks and the way it is pasted on.
When you apply it, you can easily position it by masking, and if you apply it while peeling it off slowly and carefully, I think anyone can apply it because it won't bite the air.
View detail
Grip strength is good!
Even if you think you have a firm knee grip, you can't help but shift forward while driving So I bought this product, which had good reviews
Attaching itself is not a problem, you just need to fit the shape and apply it so that no air gets in from the edges
It feels a lot more Hold when running and I look forward to future runs
And then there's durability (Peeling) I'm worried about the quality of the product, but I hope it will last a long time
View detail
I'm happy enough
We don't have one for Ducati's DIAVEL 1260, so we're going to have to go with the Universal Oval Type Depending on the shape of the tank
I cut, shaped and pasted it with Cutter
About the air bubbles that remain when applying the adhesive
Apply a few drops of neutral detergent to the Pad and Tank while spraying it with a mist of water
"Water paste" If it is done in, it can be beautifully stretched, and even if the position is Gap, it can be reapplied
Immediately after application, there will be a few air bubbles left, but they will disappear within two weeks
(The first two images are just after the application and there are still air bubbles on the first two images:(1 Set of 4pcs. eyes without air bubbles)
Also "Water paste" The adhesive strength does not degrade with the use of this product
(I'd rather it was too sticky and I'd like it to be weaker ...)
After putting it on, I think I wear Jeans, not Riding Pants, but I wear Jeans a lot! but
Knee grip on the previously slippery Tank surface and it slips and doesn't slide
Extra force had to be applied, which resulted in unnatural cornering
You can grip firmly with the decoration of the pad so that you can get a stable ride
I feel like I can now do it
View detail
Expensive but good product
'19 I put it on the ZX-6R
I think it's partly because of the riding posture, but before I put it up, the tank slipped a lot
I had to do a knee grip with more force than necessary, which resulted in a wobbly leg and knee pain after the ride It was awful
When I put this product on the tank, the feeling of hold increased and it doesn't slide down beautifully!
It made the ride a lot of fun
I always ride with Jeans and I've never felt any particular warts and bruises
The strongest negative points are as follows
Expensive for the parts
I don't like the design (warts and all)
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Riding is a lot easier now
Riding is much easier now
Unlike the cheap ones, it doesn't feel like it's going to come off But it should be a little cheaper
I'm very nervous about sticking it on because it's so sticky
However, I would like to introduce it to another Motorcycle
View detail
Fits: SUZUKI GSX-R600, SUZUKI GSX-R750
Royal road
Used in GSX-R600 K9.
These Pads are various in each Manufacturer
Large body [Color] Although it was Clear, there were many places difficult to match with the car body
Manufacturer here also has a setting for Black
It was Don Pissha for my own car that had been hardened with almost black.
Usability is ? ? ? Well, I guess this is something like.
Since we also incorporated Rear Sets almost at the same time
Is it the benefit of Position change
I did not know whether it was the benefit of Pad.
However, "As it is" There is a sense of Hold in
It goes without saying that it became easier to run.
View detail
Fits: SUZUKI GSX-R600, SUZUKI GSX-R750
Also necessary for town riding
Excellent product that will confirm the importance of Knee grip again.
Those who ride with thin Pants may feel a bit painful, but I think that when wearing a Motorcycle should wear something of such a thickness that it does not hurt in the first place.
When I was wearing Racing suit and Leather pants, I felt that the sense of unity with the vehicle increased further.
Even when pasting, it is a wonderful point that it is easier to position because the soft material is used.
Stain included in the attached Sticker, Body's Film is hard to peel off because it breaks.
View detail
Is this OK?
Looking at Impre of this site, the dish that I was very interested in, "Stomp Grip" I bought.
Although I bought a car model exclusive item, Carbon Tank Pads has already been installed in my Motorcycle, so first cut off the useless part. Even Scissors got cut cleanly.
Paste after cutting. Carefully paste so that air bubbles do not enter little by little from the edge. The pasting work is Quantity : Pair (for Left and Right) In about 15 minutes.
When using it ,,, This is good!
Knee grip is now easier. Strange power will not enter the shoulders and arms. Long riding became tiring as well.
I think that it is a pretty good item for Motorcycle taking a forward leaning posture.
I wish I had bought it sooner..
View detail
It was expensive, but I was glad I bought it
At first I went to Home center etc. and thought about trying various things, but made it for exclusive use.
Although it is Small in terms of area, if you stick it in line with the Thigh Line when you are on the ride
You get enough Grip. It's as expected.
Although there is a story that it is painful, but there is no problem personally.
It may be painful if it is an extremely thin Pants or when it gets on for a long time.
Because it is the color of Clear, but the material is looking at Blue as compared with Tank Pad of PROGRIP
Because of the thickness it is quite conspicuous.
It is not a feeling that there is a presence, but if you want to make it Custom, Black might be better.
Although it has nothing to do with the product, the sticker attached with extra was happy because I was good with Parenthesis unexpectedly.
View detail
Knee grip to High grip!
【What made you decide the purchase?】 Seat of Ninja 250 SL was made to slide forward in front and I tried to fix my waist with Knee grip, because I slipped, I wanted something to ensure Knee grip and similar to zank of zx - 10 r By saying that there is a place saying that it can be attached by Small processing.
【How was it actually used?】 It is good. You can prevent the Knee grip from feeling a sense of stability and slipping. Muscle pain in my thigh internal gluteus muscle was relieved. In addition, although 3 M glue is every time, it has a distinctive smell like sour smell or hospital smell. I was worried about Clear and Black, but Tank Cover was black anyway, Black thought that dust would stand out and made it Clear.
【Was it difficult to install? (Hard parts case)】 I degreased the place to paste with PartsCleaner, paste from the center, I feel I will push out bubbles to the edge to the edge. However, because the adhesive strength is Large, it will not be possible to fix it once it sticks a bit!
【Please tell me the point of installation and hang (in the case of Hard parts)】 After all, since it is a diversion of ZX - 10R, there is some need to cut out. Especially the slightly pointed portion cuts the point a little bit round as it seems that it will peel off as it comes to the part where Tank Cover just hangs. Also, since I'm a shit, since my knees do not come in the real Tank part, it was OK to paste it on the part of Tank Cover.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) ]
[Is there anything I was disappointed about?] Because it is made in United States, many of things like paper Waste stick to the surface of Pad and it was troublesome.
【Hope for Manufacturer - Please tell me if there are any improvement points】 I think I should have had for Ninja 250SL.
【Have you compared items?】 None.
[Others] All Instruction Manuals are English Version, "Stomp Grip" Sticker is attached, but printing was laughable at the moyamoya.
View detail
I can accelerate it exponentially
CB400SF (NC41) Attached to.
I had to cut a bit when I wore it, so I made Design four stars.
Iboibo is fine, I have a length, I think that it is quite painful if it is only G bread.
However, since I have heard that Pad of this hand wears down as it wears down, it is a consumable item,
I think this is fine for this.
It is comfortable to use, but when you accelerate from Corner Knee grip and you gut,
I was able to accelerate with confidence.
Although it is not done now, Brake which stabilized as a tight even at Bure King
I am practicing so that I can apply it.
Although it looks a bit, I thought that it was a necessary item for improving the Riding technique.
View detail
Fits: SUZUKI SV1000, BMW R1200GS, SUZUKI SV650 03-09
It is impossible for Stomp without Grip
Since Clear which I used for 2 years became soiled, it was replaced.
I bought Clear for GSX 1300 R HAYABUSA and cut and pasted the part overlapping with Carbon Tank Cover, but in particular the dirt on the border around is conspicuous. The dirt that entered the border can not be removed by blending with the adhesive. Clear so it stands out more.
That's why I did not need to Cut Others for Vehicle I tried Small things, dare to Black. This will make the dirt inconspicuous.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Dirt is noticeable in transparency
I replaced it because I used it for 2 years.
There was no Yellow Bun being told in the streets, but it is conspicuous that the Black edge and the surrounding edge become black.
The outside temperature was about 10 degrees, but it did not have any difficulty to peel off. It got easier to peel off more easily with a little heating with Heat gun.
I always want to keep beautiful cars clean.
View detail
Satisfied
Because I did not want to kill Honda's Wing mark, I chose Clear.
Large diameter bubbles will not enter if you position firmly and paste little by little.
I entered fine air bubbles but it can not be helped.
View detail
Required to hold the body
Every time I change trains, I use it regularly, but it is better to have had public roads as well.
It is very easy to hold your body during Brake.
However, we recommend leather bread because it is painful in a jeans or the like.
View detail