Reviews
If you want to use Titanium for practical purposes rather than Attachment, this is the way to go.
Since I changed the Caliper, I also changed the Mount Bolt to Titanium.
I thought about it once because I feel more secure with large hand like Beta titanium, but it is too expensive.
I don't think I could spend that LargeGold on a product that is just a Bolt that has been NC-turned and colored, so I eliminated it from the list.
When I looked for a place with good cost performance, I found Titanium64, so I bought it this time.
If Titaniumium Bolt is made of Titanium64 alloy gold, it is not a product that has a difference in strength between Large and Small depending on the manufacturer.
As a person who doesn't care about appearance, there was no element of hesitation for me.
The Bolt itself is Titanium from steel, so I could tell right away how light it was in my hand.
However, the weight of the Bolt itself is quite small as the Factor that constitutes the Front, so it becomes a Part with little influence.
I didn't notice any comparative improvement in driving performance with the Coco as Titanium.
View detail
Reasonable compared to other products
I bought this product because I was worried about the rust on the front axle pinch bolt of my ZX-10R that I have been riding for 15 years. I was hesitant because other companies' products are very expensive, but I think this product is reasonable even if it is the same 64Titanium. I don't know about the improvement of rigidity, but I don't think rust will occur in the future. View detail
The texture is good
Quantity:I purchased this to change the Caliper Bridge Bolt that connects the 1 Set of 2pcs. calipers. For some reason, when I quoted OEM parts, they were out of stock for some reason, so I bought them as a replacement, and I'm happy with their good texture. View detail
Fits: HONDA vtr1000sp -1, HONDA vtr1000sp -1
strength reduction
Even 64Titanium has a lower strength than Chromoly, which reduces the strength of Caliper.
It will not increase in strength.
It is very dangerous to note this, including the act of disassembly.
View detail
Do you find it hard to feel the effects?
【good point】
Lightweight yet strong material:I changed to the Titanium Bolt, so there is some lightening effect.
The Bolt itself is also light, so you can feel that it's getting lighter.
[Bad point]
It's too expensive in any case.
[Summary]
As a product, it's only a few Gram's difference and a self-satisfied product.
If you're looking for a cosmetic product, it's a product that doesn't work to satisfy you in that regard.
View detail
Fits: その他 Brembo 40mm casting calipers, その他 Brembo 40mm casting calipers
Lots of scratches on the Bolt head.
It's a Titaniumium Bolt, so I don't think lightness and strength are an issue.
There are many scratches on the head of the cap bolt. A little more care in packaging would be appreciated.
View detail
Fits: その他 Brembo 40mm casting calipers, その他 Brembo 40mm casting calipers
scratchy
The Titaniumium Bolt is naturally light and the quality of the screw part is not a problem.
On the other hand, there are many scratches on the head of Cap bolt because it is packed in the Vinyl bag, and I feel that the texture is inferior compared with the new Titanium bolt of the other companies. I am thankful if you take care of the packaging.
View detail
Titanium is burning well
It's totally self-congratulatory Parts!
Size is M6×15mm P=1.0
I'm happy with the way the Titanium is burned, just the right amount of Large!
For those who like Titanium, it's Recommends (^o^)
View detail
Fits: YAMAHA YZF R25, YAMAHA YZF-R3, YAMAHA YZF R25, YAMAHA YZF-R3
It's broken
I bought this product to change the bolts of my brake discs to Titanium, and a mechanic 1 pc was broken before the prescribed torque Quantity:It's a set, so you can't use it even if you can't use 1 pc, so you can't use another manufacturer's I asked for Titaniumium Bolt again View detail
It looks good
I took the plunge at CaliperOverhaul and replaced it
The brake performance will not change, but it looks custom
View detail
It's Polished, not Rust
Replace the OEM bolts with RustRust's OEM bolts during normal caliper overhaul The tightness of Screw is snug with Snap You can't feel but look Beauty
I'm happy with
View detail
I think it's very good
It's almost impossible to tell the difference while driving, just the indescribable difference when you tighten up the Bolt The tightness may be different from the normal Bolt, it's not as noticeable as the usual exterior parts, but it's effective I think that the "Mere Old Man" is a definite part of this model I like this kind of modification View detail
Overspecifications (Lol)
VTR250 (06') mounted on
It could have been a cheaper one and not Titanium, but We-Big has a VTR This was the only one for Rear Caliper
I couldn't see the benefit of this slight weight reduction and rigidity when I installed it (Lol)
But compared to a rusty OEM Pin with Stages, the Pad runs smoothly I can now get it No wonder (Lol)
For some reason I found it a bit longer than the OEM Pin Is it because it's shared with other cars?
Well, don't worry, you can go deep into it without any interference and the lid can be placed on it without any problems
Then there's the durability of the product after you've used it
View detail
The thing is good, but there is no doubt to buy it in the nearby shop.
I was afraid that I should have bought it at a nearby Shop before evaluating.
Items arrived after waiting for about two months arrived completely different from OEM 25? Pitch by 45?.
It is the worst Shop that is unprecedented even if you call on the date of arrival.
Although correspondence is also good if it is stock with stock, the person in charge such as inquiries is the worst.
View detail
Fits: その他 Brembo 40mm casting calipers, その他 Brembo 40mm casting calipers
It's light.
Compared to normal, shape and lightness, texture is different.
More than anything, PadTweezers is good not just Bolt!
However, it is even better if the price is cheaper a little more.
View detail
Fits: その他 Brembo 40mm casting calipers, その他 Brembo 40mm casting calipers
webike properly!
When the item arrives and opened, since the shape of the photograph and the real thing are different, I reviewed the photograph of the order history and the real thing many times again!
Since it has no influence on the installation, it was installed as it was.
Check with webike properly!
View detail
Looks and performance is very good
Corrosion of OEM's Caliper bolt began to worry, I was looking for various BridgeBolt, but I heard the reputation of this item and introduced it this time. The impression that I picked up the product was much lighter compared with OEMBolt! It was as light as Big. It is truly Titaniumium Bolt. Regarding the exchange, I checked the service manual and tightened with Torque prescribed, but the feeling of tightening was so light that it was the place to worry whether I could really tighten it. I felt that the feeling I grasped by Brake is different from usual. Although I tried variously, Touch felt different from the past so I changed the position of Lever. I felt that OEMCaliper also changed this way. View detail
The price is expensive but it's worth the exchange.
I exchange the Front brake around little by little with TitaniumParts, this time I tried to replace Rotor bolt with Bolt of Titanium. I replaced it from Bolt of ToughOEM to Bolt of Titanium 64 and I was satisfied with Refreshing just by looking! It was lightened and it was easier to knock down Corner. View detail
very satisfied
From the appearance, texture, shine etc. Very satisfied
It was nice to have it, is a dish
I feel I have narrowed the surroundings of Brake
Just a longer OEM is felt
View detail
Titanium 64 Bolt for Caliper Mount M10 P1.5
This is very light. The bolt head is made very beautiful but the thread is not beautiful because the surface is not flat. Because the bolt is made of titanium, it is not scratched when tightened with a socket View detail