Reviews
Fits: Others
Rear brake master OH
The car was 10,000 km old and had been used for 10 years, but we decided it was time to replace it.
Large is correct.
The seal had lost its tension and the tip had become rounded.
Piston shape is different, so the piston has to be re-youth.
Replace CupSeal and Return spring.
Dust Boots shape is also different, so reYouth.
This setting is supposed to be for front master.
But that's just it...
The assembly could be done easily by setting up the parts that would take care of it.
View detail
Fits: その他
For Brake masterOH
Purchased a used car that is 10 years old and has a little over 10,000 km,
I thought it was time to replace it. I thought it was time to replace it.
Parts is Piston and CupSeal is Quantity:Set and
Return spring and Solid Type Cup.
The removed OEM Product had a sagging CupSeal and had lost its tension.
DAYTONA products look exactly the same as OEM products, but CupSeal has a taut pin and seems to apply firm pressure.
After the replacement, I feel that BrakeTouch has become clearer.
View detail
Fits: Others
It is only an Other Brand Product.
I used it on a TriumphTIGER800 Rear master cylinder OH.
First of all, the size of the OuterDust Boots is different when removing them, so be sure to remove them without damaging them so that they can be reused.
Inner Piston is the same in size.
You can see how grateful we are to have CupSeal in the Inner Kit Package with Rose!
Remove CupSeal from vehicle OEM Piston.
Replace CupSeal only.
It's similar to the technique of old car maintenance where parts are difficult to procure.
If this is not the case, then replacing the MASTERAssy with an external one would be one of the methods.
View detail
Fits: Others
Touch is now better.
I bought this for the Nissin OEM Master Cylinder Repair for my 98 GSF1200, and although it is not available for the Nissin OEM, I thought it was a bad idea since it is a Horizontal Type and the piston diameter and shape are the same. I was very pleased with the results. I had to choose between the Ichi and the Drumstick, but since you post a picture of the part number itself, I was able to purchase the Large. View detail
Fits: Others
Used for TZr50R
I used it to overhaul the front brake master cylinder of my TZr50R.
The deciding factor in the purchase
The Boots on the front brakes master cylinder had been cut off, so I thought I would just replace the Boots, but since it was not available as a Single Item, I decided to Overhaul it as well.
OEM Kit for TZr50R (59X-W0041-00) As of February 2021, parts for this model are still available, but they are priced at just under 4,000 yen.
I was thinking "4,000 yen for a part that can be used if I want to use it..." and then I found out that this product can be used.
The price is about 2,500 yen, which is cheaper than OEM Parts, so I decided to buy it.
Installation
It was my first time to overhaul the brake master cylinder, but it was relatively easy to do.
There is no instruction manual, but I installed it while comparing it with the original OEM one, and the replacement itself was completed in a few minutes.
Impressions of use
The one that I used so far was old, or the Touch of Brake was very bad, but it was improved.
At the same time, Caliper also overhauled, so I don't know which was the cause. (Lol)
It is less expensive than the OEM product, but I think it is solid without fluid leakage.
Products compared
I compared it with OEM Product. I bought this one because of the price, the evaluation in the impression, and the fact that it was made by NISSIN.
【Review】
I am very happy with the price and the accuracy of the parts.
In my case, Overhauling also improved the Touch, so I was glad that I didn't just replace the Boots as a result.
View detail
Kindness!
I bought it for Overhaul of NISSIN Forged Radial master.
I haven't used it yet, so I haven't evaluated its effectiveness.
OEM Parts are separate with Packing included.
Cylinder has Packing built into it.
It is very kind and grateful only for the most time-consuming work.
View detail
Fits: その他
Radipon + Yamaha Brembo
I installed the old Nissin Radipon and Yamaha Brembo on my SRX600.
However, after about 3km of test run, White smoke came from FCaliper!
Rotor has locked up.
I looked up the model number on the Internet and bought a replacement kit.
When I disassembled the Master Cylinder, I found that it had different parts than the ones I purchased.
The spring length is different and the spring holder is silver, so it seems that the previous owner installed the wrong parts for the new model. The replacement work is easy that anyone can do, but the air venting was difficult, I tried a lot of Net research, but in the end, I removed the Caliper from the Fork and pulled the Piston with a tool and filled the Caliper with brake fluid, and the air venting was completed easily. It was very easy.
I also replaced the Seal on the F-caliper, just in case.
Considering the replacement KitGold and labor, it was safer and more secure to buy a new one instead of a used one.
View detail
Fits: Others
Check back often.
Purchased for the Master CylinderOverhaul.
No complaints. A little BALI? I thought, but not so much that I couldn't assemble it.
It's worth checking out, especially since the RubberBoots where Lever hits are very easy to tear, and when they tear, the rust progresses quickly from there.
Well, it would be best if only Boots could be replaced.
View detail
Fits: Others
It's good enough
Fourteen years after I bought the car new, I used it for a MASTER Overhaul because the front brake fee ring had deteriorated.
Overhaul of Caliper was also carried out at the same time, but it can be assembled properly and the fee ring is perfect.
View detail
Fits: Others
I think it's good
This product, I think it's just mine, but it's not a Nisshin product” So it's a DAYTONA” product.
I checked the slip many times and it seems to be correct, Size was 5/8, so &rdquo I've done it, but it was just a matter of time.
Started work, all Rose & rarr; cleaning & rarr; mono replacement. Just in case, measured with Caliper. Perfect! There was a bit of anxiety, but the work was completed with no problems.
If it's a DAYTONA product, I think it would be helpful if DustRubber would just release the product. . I think.
After all, it's nice to be new.
View detail
Fits: Others
Trust Brand
I have a CRM250RR (before the AR), but the front brake was about 15 years ago I remembered to OH it once Because the front brake has become less and less efficient as expected recently (I can't JackKnife it) I performed OH at the same time as MASTER and Caliper When I looked at the parts that arrived, I found that the Piston is shorter than the OEM After much consideration, the dimensions after the front of Spring seem to be the same as OEM Pistons, so it is a problem in principle I decided that there was no such thing and installed it as it was As a result, the stopping power of new car was revived without any problem In addition, it was stated in Package that it does not fit the OEMMASTER It is only at my own risk View detail
A must-have for S-1 maintenance
S-1Front brakes master cylinder maintenance Purchased
I couldn't order from YOSHIMURA head office, so I searched for information on the Internet I fished around and came up with this component
The fit was perfect
A must-have for regular maintenance
View detail
Fits: Others
For updating from old model
Reverse link release
Changes to the inverted Front fork and the results of Large surgery
As Front caliper becomes tokiko 6p, as a result, MASTER diameter does not match and MASTER change
14mm→5 / 8
that time
Push rod formula MASTER from the old year, purchase to update the New Year's Lever straight press..
As a result, complete without problems.
View detail
Fits: その他
Mandatory items for Maintenance
As long as you are on a regular basis, you will definitely need it in Maintenance. There is no problem such as quality etc.. Master cylinder / Lever's Fe Ring is good, so we have Fee Ring etc. as star 5. View detail
Fits: Others
It is the same as 4K0-W0041-50.
It is fully compatible with Yamaha OEM Product. This one is cheaper. And here Bush is already built in.
I just wanted Dust Boots, but since it was so much trouble, I decided to disassemble it completely, Overhaul it and it got better.
View detail
Fits: その他
If you are not Sale, you dare not buy it worth it
To Overhaul the Master cylinder of CFL d Brake of KLX 125 NISSINNisshin : 23653
[NISSIN Repair Parts for Master Cylinder] I purchased Master Cylinder Repair Kit
Compared with OEM, the shape of Piston is different but there is no problem in use
I bought it because it was 1,545 yen in Sale but I think that it would be better to buy an OEM Parts Number for the current price of 2359 yen
The good point is that it is a bit cheaper than OEM Parts Number because it has Rubber cover, Washer, Circlip
View detail
Fits: その他
In Raipong's Overhaul
Since the movement of Nisshin 's Rap - Pong with it comes from bought a second - hand car, it got worse so Overhaul. In addition I will also Overhaul the brembo 4 pot Caliper. By the way, in case of brembo Seal kit can not usually purchase, so we will order as OEM Parts Number from Honda.
There was inventory in Wa Big, it arrived soon. Nisshin's Overhaul kit is also in stock! I really appreciate it. (We do not write ProductNo because we are not responsible. Please check with Net. )
View detail
Fits: Others
Deals from OEM
OHKit is high with OEMMASTER, but Nisshin costs about half price and COSPA is good.
As I usually exchanged Brake fluid normally seven years later.
Especially OH is also completed without any troublesome matter.
Honest air bleeding after OH takes time it is Large strange.
View detail
Fits: その他
Since a Boots and a Snap ring follow a considerably cheap top compared with a pure MASTER, it is very profitable.
Since a Boots and a Snap ring follow a considerably cheap top compared with a pure MASTER, it is very profitable. View detail
Fits: Others
The Packing of a Daytona Nisshin has slightly bad durability. . . It grasps, and if once pressure is extracted, it will be able to grasp deeply rapidly. If such a condition appears, it is solvable by this Kit. Since work is d
The Packing of a Daytona Nisshin has slightly bad durability.
.
.
It grasps, and if once pressure is extracted, it will be able to grasp deeply rapidly.
If such a condition appears, it is solvable by this Kit.
Since
work is delayed just for a moment, the way on which the Motorcycle store was consulted with may say it.
View detail