Reviews
Fits: KAWASAKI ZXR750R, KAWASAKI ZXR750R, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI ZXR250, KAWASAKI Z250LTD BELT DRIVE, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI NINJA ZX-7RR
ESTRELLA's crying place.
ESTRELLA's Restore, which has become immobile, maybe the end of the line here.
Just before it became immobile, it was leaking oil frequently, and I was looking for various causes this time while restoring it.
(1) Deterioration of Piston ring → done.
(2) CamTensioner problems→done.
(3) Gasket degradation → done.
I have been repairing the grains in various ways, but there was a blind spot.
There was oil leakage from the root of the oil pipe on the crank side.
Is it Gasket?
I took it off for a test, and as I expected, it was Gasket. I replaced it.
Oil pipe, as the name implies, is a pipe through which oil passes, but why is it attached?
It has to do with oil pumps.
Oil pump
Equipped on the lower front side of the cylinder block and driven in conjunction with the crankshaft.
The OilCleaner sucks up oil accumulated in the oil pan and supplies oil to the sliding parts of the cylinder head and cylinder block. 。
Think of it as gravity, so Oil goes down too, it accumulates in the Oil pan.
The oil pipe is where the oil passes through.
Oil pipe
Oil pipe is a piping that serves as a route to feed engine oil. 。 Engine oil plays a role in lubrication and cooling, and oil leaks can cause seizure and other problems. 。 Also called oil transmission pipe.
Engine oil not only lubricates the engine, but also cools it.
If the engine is air-cooled, the engine oil cooling effect is even more important.
And if the oil as an auxiliary role for cooling does not circulate correctly due to leakage, .......
→If the amount of engine oil is less than the proper amount, a strange noise may occur while driving, or the engine sound may become louder than usual. 。 In addition, low engine oil reduces the natural lubricating effect of the engine, causing a risk of engine seizure in some cases.
In my case, I don't know why it didn't burn out... I was able to manage to ride it while adding oil... now that I think about it, it's scary (laughs).
Gasket replacement.
Procedure
Remove the oil pipe from the cylinder head side, the carburetor side, and the crankcase side.
↓
(2) Gasket of rubber is confirmed at the tip of the pipe on the crankcase side. 。
↓
Replace (3).
↓
Assemble in the order of ? ?→?.
[After exchange]
◎Oil leaks are completely gone 。
◎A little test drive made it run Smooth.
This completely fixed the Oil leak. 。
Regardless of the year, it is a part that comes in contact with oil, so deterioration is to be expected. If you feel oil leakage even a little, it may be a good idea to suspect this part. 。
It seems that ESTRELLA has many examples of repairs here (laughs).
The only thing left to do is to adjust Tappet.
View detail
Fits: HONDA CB600, HONDA CB600F, HONDA CB600F, HONDA CB600F, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET250, HONDA HORNET600, HONDA HORNET600, HONDA HORNET600S, HONDA HORNET600S
FOR CB250F
Actually I could not find this item in my country (Bolt washer- 6X12 934140601200). Finally I bought it from webike. It is authentic. Very good packaging. Fast shipping. Thanks to the webike team. It has not been installed yet. Highly recommended. View detail
Fits: KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125, KAWASAKI KX125
Genuine Kawasaki Clutch Cover Out Gasket for KX125 2001
I need a lot of parts to get this old and slightly damaged bike back to ripping up the dirt, these small parts are definitely needed for that purpose. This was a rebuild that was not going to be a quick fix. Finding the part was easy using the help pages from Webike. I did not really pay much for shipping as most of the parts were small and pretty light. Even though I got the fast service from Fedex, the price was still very good. All arrived with me in less than a week. The gasket was in perfect condition and Webike kept this nice and flat so not to distort the shape.The flexibility is enough so not to be an issue if it gets caught whilst installing. All the mount holes aligned correctly and fitted in less than half an hour. Now this is one of the many jobs that is completed, onto the next one for this old girl.The service I got from Webike was brilliant. I will be back for all my OEM parts now. Thanks a lot Webike View detail
Fits: KAWASAKI NINJA ZX-6RR, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R
Genuine Kawasaki Gasket for NINJA ZX-6R 2005
This is a crank case cover gasket. Also I had to change the actual crank case for this too so a new gasket was a good purchase. The part number was found using the methods I generally use, either the help pages that Webike supply or direct to the manufacturer websites etc. I found the price of these was really good and better than I could source locally here in the UK, just like the other gaskets. As this was part of a larger order with many other Kawasaki parts, the shipping worked out to be brilliant. Everything was very well packed and arrived via EMS within a week of ordering. All the empty space was filled with air pockets and bubble wrap. Most of the parts were packed in the genuine OEM packaging anyway. Webike even taped the outer box to ensure, nothing could fall out or escape during transit. The parts all arrived in perfect condition. The gasket was kept nice and flat and did not suffer any bends or mishapen in any way. This is an essential gasket so I had to take a little care in fitting it. Didn't take too long and everything was back together and ready for firing up. The gasket fits perfectly and along with the new crank case, that is one more thing finished off. Very happy with the result. Thanks Webike for your hard work. It really is appreciated. View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA LITTLE CUB
Right Part
When I bought my bike these caps were missing, I had to enlarge the hole a bit because my dust guard is not original but they fit and look great! View detail
Exactly the right screw
This is exactly the right fit for my C50. When I bought my bike the screws were rusty, so I found the OEM part number and ordered this and it's the exact part for my bike. View detail
Fits: HONDA CRM125R L, HONDA CRM125R M, HONDA CRM125R N, HONDA CRM125R P, HONDA CRM125R R, HONDA CRM125R V, HONDA CRM125R X, HONDA NSR125F, HONDA NSR125F, HONDA NSR125F, HONDA NSR125F, HONDA NSR125F, HONDA NSR125F, HONDA NSR125R 1, HONDA NSR125R K, HONDA NSR125R L, HONDA NSR125R M, HONDA NSR125R N, HONDA NSR125R P, HONDA NSR125R R
Genuine Honda Spring for the NSR125R 1998
I was doing some work on the NSR125R and noticed an issue with the spring for the exhaust, not in very good shape and even though it is an older bike, this still needed to work as it should. I checked on the help pages from Webike and found the correct part and cross referencing Honda schematics sections. The price from Webike was a lot cheaper than I could source locally and decided to buy from these guys. I always have other parts in my order and rarely buy one part at a time as I can save with shipping items together for the same kind of price depanding on shipping points. The order was dleivered to my door in 5 days from shipping which is great and just what I needed. I hate when you get parts that really take a long time to eventually get to you and for this reason, I use EMS. The spring was in a nice littel Honda packet and all the other items in my order were packed really well. The spring is a good part, there were no foreign objust with the part, no dust, grit or anything else. It was a really clean part. You will never see this when it has been fitted but it does look really nice when new. I fitted this really quickly as the exhaust was already dismantled. This made the bike sound and feel a lit better not it had good compression with no leaks. Thanks Webike, very happy customer. View detail
Fits: KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6RR, KAWASAKI NINJA ZX-6RR, KAWASAKI NINJA ZX-6RR, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R
Genuine Kawasaki Clutch Case Gasket for ZX6R 2006
I need a lot of parts to get this old and slightly damaged bike back on the road, these small parts are definitely needed for that purpose. Finding the part was easy using the help pages from Webike. I did not really pay much for shipping as most of the parts were small and pretty light. Even though I got the fast service from Fedex, the price was still very good. All arrived with me in less than a week. The gasket was in perfect condition and Webike kept this nice and flat so not to distort the shape.The flexibility is enough so not to be an issue if it gets caught whilst installing. All the mount holes aligned correctly and fitted in less than half an hour. Now this is one of the many jobs that is completed, onto the next one for this old girl.The service I got from Webike was brilliant. I will be back for all my OEM parts now. Thanks a lot Webike. View detail
Fits: KAWASAKI ELIMINATOR 400, KAWASAKI ELIMINATOR 400, KAWASAKI ELIMINATOR 250V, KAWASAKI ELIMINATOR 250V, KAWASAKI ELIMINATOR 250V, KAWASAKI ESTRELLA, KAWASAKI ER-6F, KAWASAKI ER-6F, KAWASAKI ER-6N, KAWASAKI ER-6N, KAWASAKI ER-6N, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA
Can be used as an alternative for Triumph SPEED TRIPLE
I am SPEED TRIPLE900mark1 (Initial Modelt301) Owned a '94.
As of late.
Neutra SW is in bad shape, actually in Neutral, but
NLamp does not light up
Even though the NLamp is lit.
Trying to get into Convenience.
When Side Stand is put up, does it stall to do ignition Cut (Igniter)?
Idling is somewhat unstable even when waiting at a traffic light (is the ignition thinning out a bit?).
In any case, when I looked for a replacement, I couldn't find it.
Dealer home country arrangement & since it is not coming soon.
I looked it up.
Kawasaki's OEM Product has the same Size as Exactly!
The miracle is that everything is exactly the same.
Replacement is easy.
Copper packing is inserted at the time of installation.
I am 1mm thick (Inner diameter 10mm) Using UniversalDrainPacking of
The Initial Model is thin in packing here and pushes the Switch too much.
Because it wears out quickly.
Trouble that will be ruined.
I heard they put it out as a countermeasure to prevent over-pressing with thick Packing.
This is unconfirmed information.
My own vehicle also had a thin (0.4mm measured) Packing.
If it lasts longer with the thicker packing, it will be a good thing.
* I thought removing the Neutral switch would produce Oil.
It did not appear at all.
KawasakiOEM Product No. 13151-1080 1.200- (excluding shipping charge) including tax
Universal Copper Packing OD 15mm ID 10mm Thickness 1mm Quantity:1pc.110- (purchased at mass retailers)
Incidentally
TriumphOEMNeutral switch part number VIN45236 (Z440)
Other Triumph models that may fit are as follows
Fits Trident 750/900, Trophy 900/1200, Daytona 750/900/1000/1200, Speed Triple 900, Sprint 900,
Tiger 900 (carburettor)
Older Triumph riders, please try at your own risk.
View detail
Fits: YAMAHA GTS1000AE, YAMAHA GTS1000AEC, YAMAHA GTS1000AF, YAMAHA GTS1000AFC
Washer that is gone before you know it.
[How is it used?
This is a resin washer to be used with the bolt that holds the side cover of the YAMAHA XJR400/R/RII.
I bought it because it had been missing since I purchased the vehicle.
I could have used a suitable external Washer, but it was not expensive and Material:I selected OEM Product because it looks like Plastic.
How was your experience with it?
I bought the side cover just in case there was a chance that it might break.
I will be careful not to lose it during maintenance.
How did it compare to other products?
I can't compare it to others, but I think I could have just measured the Size and let Universal Product's Washer bite.
[Points to note]
Be careful not to lose it during maintenance.
View detail
Genuine Yamaha Crank Case Cover 1 for MT10 2022
This was a part that my customer asked for. They had a small accident which resulted in their crank case cover gettting a little scratched up. I found the correct part number by using the tools available from Webike help section. The part was pretty easy to find that way. Webike's price for this part was very good value. A lot lower than I could source locally. Along with some other parts in my basket, arrived in 5 days via EMS. All the items in my order were packed individually by Webike warehouse and all nicely padded out in the box so nothing could get damaged in transit. There was a few gaps between the parts in the box but Webike think of the customer, and fill that space with bubble wrap and air pockets so nothing can be bounced about in transit. All arrived at my door perfectly. The crank case cover is a good piece of manufacturing. The threads are really neat and not sharp with burrs or unfinished. The paint on it is a perfect match to the one being replaced, it is a nice satin grey, I think this is a standard Yamaha engine colour paint. It look awesome once fitted. DIdn't take too long to fit, pretty straightforward, just eveything in reverse really. Take your time and you will be just fine. With this being a new bike anyway, it needed replacing for it to look as new again, mission completed. Very pleased, thank you Webike for all your hard work and dedication. View detail
Fits: KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10RR, KAWASAKI NINJA ZX-10R SE, KAWASAKI NINJA ZX-10R ABS, KAWASAKI NINJA ZX-10R ABS
Genuine Kawasaki Generator Gasket for NINJA ZX-10R 2017
This one is the crank case gasket on the generator side as when I was checking out the bike, this seemed to be delaminating. Small bits were clearly perished. The part number was found using the methods I generally use, either the help pages that Webike supply or direct to the manufacturer websites etc. I found the price of these was really good and better than I could source locally here in the UK, just like the other gaskets.As this was part of a larger order with many other parts, the shipping worked out to be briliiant. Everything was very well packed and arrived via EMS within a week of ordering. Any empty space was filled with air pockets and bubble wrap. Most of the parts were packed in the genuine Kawasaki packaging anyway. Webike even taped the outer box to ensure, nothing could fall out or escape during transit. The parts all arrived in perfect condition. The gasket was kept nice and flat and did not suffer any bends or mishapen in any way. This is an essential gasket so I had to take a little care in fitting it. Didn't take too long and everything was back together and ready for firing up. Very happy with the result. Thank Webike. View detail
Fits: KAWASAKI GPZ900R, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R
Genuine Kawasaki Clutch Cover Gasket for ZRX1200
I need a lot of parts to get this old and slightly damaged bike back on the road, these small parts are definitely needed for that purpose.Finding the part was easy using the help pages from Webike. I did not really pay much for shipping as most of the parts were small and pretty light. Even though I got the fast service from Fedex, the price was still very good. All arrived with me in less than a week. The gasket was in perfect condition and Webike kept this nice and flat so not to distort the shape.The flexibility is enough so not to be an issue if it gets caught whilst installing. All the mount holes aligned correctly and fitted in less than half an hour. Now this is one of the many jobs that is completed, onto the next one for this old girl.The service I got from Webike was brilliant. I will be back for all my OEM parts now. Thanks a lot Webike View detail
Fits: HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM50, HONDA CRM75R K, HONDA CRM75R L, HONDA CRM75R M, HONDA CRM75R P, HONDA CRM75R R, HONDA CRM80, HONDA CRM80, HONDA CRM80, HONDA CRM80, HONDA CRM80
ถึงจะส่งมาคนละพาร์ทกันแต่ใส่กันได้พอดีตรงรุ่นส่งไวมากๆ View detail
Fits: HONDA NBC110 XD, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA CROSS CUB50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110PRO
After the replacement, it fixes the Seat tightly.
Suction cup was replaced because it was deteriorated and the Seat was moving slowly while driving.
After the replacement, it fixes the Seat tightly.
The old one came off easily if I struggled with force.
When you put the new one on, you need to replace the hole between the prongs and the Seat.
Spray with Silicon spray and it goes on easily!
I'm not saying it's impossible, just that it's extremely difficult to fit without Spray.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA CROSS CUB50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB 50
It is a spare part of the rubber seal inside the engine of the super cub pro to wait for maintenance. View detail
Fits: YAMAHA YZFR1 (YZFR1FB), YAMAHA YZFR1 (YZFR1FCB), YAMAHA YZFR1 (YZFR1FCL), YAMAHA YZFR1 (YZFR1FCR), YAMAHA YZFR1 (YZFR1FL), YAMAHA YZFR1 (YZFR1FR)
Replacement graphic needed
I had a small scratch on one of my decals so decided it was about time to get that changed for my bike to look new again. Finding the correct graphic was not particularly hard using the Yamaha Parts Catalogue. The shipping was good due to the fact I already had other items in my order. From ordering to being delivered was 8 days including a weekend so not bad at all. Upon delivery all the items were very well packaged. I was a little worried that with this decal being flat that there may be issues with it being folded. Nope, this was not the case. It was nestled neatly in teh bottom of the box, surrounded by padding. The decal itself looks awesome on and the quality was second to none. Thanks for the help Webike, great stuff View detail
Fits: YAMAHA YL50 BJ (BASIC JOG), YAMAHA YL50 BJ (BASIC JOG), YAMAHA YL50 BJ (BASIC JOG), YAMAHA YL50 BJ (BASIC JOG)
very satisfactory
I was surprised to find OEM parts for a 16-year-old moped when I searched for them.
I thought that OEM parts were usually only available from suppliers, but I was surprised twice because it was so easy to get.
I am satisfied with the Large change because I got the parts I had given up on.
View detail
Fits: HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125, HONDA GROM125
Replacement Left Side Lower Cover for the Grom
About quality and texture: I am happy with the quality of the left side lower cover from Honda. Made from plastic with a matte black finish. About the feeling of use: The genuine Honda replacement part fitted perfectly with the mating side panels upon install and ties together the contrasting metallic black side panels and pearl red fuel tank panels on my Grom. Products to buy together: Some replacement Honda fasteners would also be desirable to purchase along side the left side lower cover as they deteriorate over time and need freshening up. Difficulty of installation: The process to install takes about an hour, removal of the seat is required to access some of the mounting fasteners and the rest are visable, once the side panel is removed as an assembly you can then swap over the lower cover and reverse the process to complete the install. A little difficult to do. Cost performance and comparison with other products: Good costing as you are receiving a genuine Honda part that has a perfect fit and finish wiith it's mating Honda parts at a reasonable price as compared to aftermarket body panels that usually have difficulties in mounting without some modification. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: The Webike OEM parts section will be most helpful for sourcing other parts needed for your repairs. View detail
Fits: YAMAHA VIRAGO 1100 SPECIAL, YAMAHA VIRAGO 1100 SPECIAL, YAMAHA VIRAGO 1100, YAMAHA VIRAGO 1100, YAMAHA TRAILWAY, YAMAHA TRAILWAY, YAMAHA VIRAGO 1100, YAMAHA VIRAGO 1100, YAMAHA TRAILWAY, YAMAHA TRAILWAY, YAMAHA TRAILWAY, YAMAHA TRAILWAY, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250, YAMAHA XT250
Yamaha OEM Grommet Installation to the TDub TANK
My 1987 TW200 tank grommet was cracked So I need to replace it.As usual I got the Brand new parts from webike shop . Before I put a new grommet onto the fuel tank need to removed the left & right side plastic covers off. Installation process shouldn't be difficult.Put a little bit of silicone grease on the rubber to help it slide easy. If you don't have, a little brake fluid will also help but not adversly affect the rubber.Try inserting one side first and working around the perimeter as you push on the grommet. I also used small flat screwdriver tool to help me with the insertion.Don't forget to cover the flat screwdriver edge with a electrical tape to prevent damaging the grommet perimeter.With a slight twisting motion and downward pressure it popped right in.Makes sure it fits as flat as possible to the surface of the fuel tank before install the side covers in.Thanks a lot webike for the support.First Class Packaging & Good Quality Service.If You need parts for your machine,webike shop is the best place to get parts at reasonable prices. View detail