Reviews
Suitable for portable, not stationary
Purchased to adjust air pressure at Circuit.
Since the capacity is small, filling a single tire is not efficient because the air runs out. TradeOff is unavoidable if the limited loading space is to be used effectively.
It is not a quiet Type and is not suitable for home use.
The 100V power supply type is perfect for use as a portable Small Type Compressor with a generator.
Other negatives are reasonable considering the price and Size.
View detail
peeling off
I purchased this product in the hope that it could be used to remove Packing, Rubber, and Sealants.
The tip of the blade is a size and both tips are taper shaped, so it seems to be good for use.
View detail
![[Aebs] Spring Hook Medium](https://img.webike-cdn.net/catalogue/19270/06191834_51c17b0f544aa_TS.jpg)
Spring Mounted Hook
It is used for spring removal and attachment of the Exhaust System.
The price is reasonable, and it can certainly be made Compact since it can be split in two.
It is not used that often, but it is good to have 1 pc. to take the spring on and off for maintenance.
View detail
Spring hook
It is used for spring removal and attachment of the Exhaust System.
The Type is a little long, so it seems to be easy to apply force when pulling, but in some places the long length gets in the way and makes it hard to work with.
It is good that it can be split into two parts, can be removed, and can be pulled by swinging it at an angle, but it turns too much and cannot be pulled properly, making it difficult to install the spring hook.
View detail
Don't scratch it.
I purchased this tool for a different purpose than its original use, such as removing parts attached to resinous materials, where I don't want to scratch the surface.
It is resin, so it is not that strong, but it seems to be good for use to remove it by placing it in a gap without much force. The surface is covered with silicon rubber, which is also resilient and helps prevent scratches.
Since the price is not that much, you can give up even if it breaks after a certain amount of use.
View detail
Spare
I purchased Body to remove plastic polish, scratches, and dirt from cowl and screen parts, but I thought that Included Parts:alone would soon be ruined, so I purchased this Spare.
I wanted only the replacement Buffing.
Brush is not used very often, so it was unnecessary, but Quantity:It is a Set, so there is no choice,
View detail
Cut
The price is not that much, and it has a good feeling of ease of use.
The handlebar is large, easy to grip, and easy to apply force.
It is also nice to be able to change the position of the blade with Slide.
View detail
nonfunctional
I understand that you use a syringe to decompress the Tank and suck it out.
It does not work at all.
In the end, it was a normal Air extraction while holding Lever.
View detail
I would like it to be attached to Rim stripe if possible.
We have applied MDF rim stripe to several (5+) vehicles in the past.
I had to replace my car for the first time in 9 months, and when I tried to apply Rim stripe, I could not find a special Gauge to apply it, so I had to order it again from webike.
I purchased a 6mm width rim stripe and was able to install it without any problem using Gauge, but I would like to see it included or packaged with the rim stripe if possible.
I would also like to see 8mm and 10mm affixed Gauge produced.
View detail
Bal Thailand Adjustment
As usual, the Ex side is adjusted with GapGap It hits 8mm Glasses, so it can be used if the round head is shaved off The accuracy of the square hole is also delicate The weakest as a weapon View detail
For cleaning.
I bought it because it seems useful for cleaning carburetor and for cleaning tight places.
Quantity:1 Set of 5pcs. so it can be used in different places, which seems convenient.
View detail
That's about it
I used it for the first time and was able to adjust it. It would have been easier if the tip was cut thinner to make it easier to get into the gap. View detail
One can be used for air bites, maybe.
Brake fluid is replaced and used to drain the fluid when air bites.
Once the Brake is inserted into the loop, it can be fastened with a special pin or tied with a needle gold so that it cannot be wiped off.
The front side of the tank is above the tank and gravity will cause it to fall down to a certain extent, but the rear side is almost parallel to the tank, so it is sometimes difficult to get out the tank.
It is a delicate item.
If it is completely air bitten and the Lever and Pedal are completely scoured, there will be no Fluid because there is no pushing force. This syringe type aspirate is not powerful enough.
At that time, if you can connect VacuumGoods or something, you can make it work, but if not, just take it to the shop. (Lol)
They did a full Route exchange at Red Baron for $3,160 for just the Rear. (Lol)
View detail
Handlebar fixing bolt is loose
The bolt that fixes the handlebar of both Tap and Dice tends to loosen, making it a little difficult to use. View detail
Just the right size
I have an example with a slightly larger size than this, but I bought this one because I felt like I couldn't hold it in terms of space.
It is just right in terms of Size feel. The dimensions and depth are as shown in the picture. It can be used mainly for placing tools in use or long items such as shafts, rather than small items such as screws.
If you want to place a screw or something, it would be better to choose Small Tray or Silicon Plate with Magnet from the same brand.
View detail
Useful if you have it. I can manage without it.
The LEDs are ideal for observing areas that are not directly visible, such as the underside of the crankcase, which is dimly lit even during the day. Well, since it is usually dark in areas that cannot be seen, it makes sense that it is with LEDs. It is very convenient.
It also stretches quite well and does not flex when stretched.
View detail
Gaps in air-cooling fins do not reach deep enough.
Very easy to use as it can be rubbed vigorously.
The core is like a needle Gold, and if there is a gap of about 2 cm in diameter, it can be plunged and washed.
Convenient for washing off mud and oil, but not for washing gaps between air-cooling fins
The core is hard and does not bend limply
Maybe I'll bend it myself before I use it.
View detail
Somewhat difficult to use
I am using it to remove the cowl of a Ninja 250SL along with another Emon interior stripper.
I think this spatula is difficult to use because the handle has a little too much curve on it;
I use this spatula only for the parts that require a lot of force because it is thick and strong. It is not suitable for delicate work.
View detail
Harder Brush
The Nylon brush is harder than I expected.
I wonder if a Paint brush would be safer considering the scratches.
It is
The waist is strong and can reach deep into tight places. is it good?
View detail
Sharp Handle with care
I'm not used to this, so I had to cut the Outer tube with this one.
It needs to be used gently.
Material without changing shape:If there were Plastic's, I'm sure they would have enough use for it.
They won't be able to cut it down.
Well, I'm not happy with it, but I guess I'll keep using it.
View detail