Reviews
Use with caution.
It is also useful for use in places where you want to dry quickly by applying hot air, or for processing resin parts by applying heat. It is especially useful for Aeroparts and ABS resin parts. Be careful not to apply too much hot air or you may get burned. View detail
Effective.
When the Grip is left on the door panel when DoorLining is removed, it can be easily removed and is very convenient. The Grip can be easily removed, but we recommend you to use it while protecting the Door panel from scratches and dents. View detail
Wound is not attached to Glass.
It was useful to remove the inspection mark sticker and inspection DialSticker after the user inspection. Cosmetically Material:You can peel off the Sticker without attaching the Wound to the front glass because it is plastic. View detail
It is useful to have.
It was necessary to remove the cowl to install the Drive Recorder and USB power supply to ADV150. When the actual work was done, it was not only impossible to talk about the cowl without the Lining Peeled Off Tool, but it was also impossible to insert the Lining Peeled Off Tool because the cowl was installed too rigidly and there were no gaps. I couldn't even insert the Lining Peeled Off Tool into the Cowl because it was too hard. I think it's more of a Cowl problem with the ADV150 than a problem with this product. It is necessary for the ADV150, but it would be useful for other motorcycles as well. View detail
long-lasting
Scraper of the common people is the genus Gold. Scraper of Ceramic is popular from before, but Scraper is a sharpening and polishing machine in the first place. Ceramic is expensive, but not being able to sharpen it is a drawback of the largest. The common people should use cheap METALscraper while sharpening it as much as possible. View detail
To adjust valve clearance
I bought it to adjust the Valve clearance on my ELIMINATOR 250
The EX250 Engine, which is also used in the current NINJA and VERSYS, is a mature engine After 60,000km, it started to make a nasty noise when idling and clattering
Thanks to this Gauge, it's now perfect and in good shape The size you need is not exactly the same as the size you need, but if you stack them up, it's not a problem Not at all
If I had to say, it's a little bit wide, so it's hard to get into the narrow IN cams, etc I even had a thought
Even TWIN is like this, so when you fiddle with InlineFour and other products, a slender, separate product You might want to choose
View detail
I'm glad I bought it
It is used to remove the bolts that are attached to the bolts
I'm glad I was able to get it off without any problems
The details are cheap, and the material is slippery and difficult to use with bare hands or military hands
View detail
Brake fluid exchange is easy to do
Brake fluid can be easily changed Easy to bleed air
It would be even better if the hose was installed with a little more thought
View detail
Perfect for washing your Engine fin
I purchased this for a Motorcycle engine wash for Vehicle
Cleaning the engine fin is now easier
I just happened to find this one in Harley's Motorcycle magazine It was available
View detail
The stuff is good But how do we use them?
You can connect the Hose and scrub it while letting the water out
… but if you have Sponge, you could have done without it …?
THE CAR WASH! I bought it because it looks like a good idea, but I don't get much out of it There may not be many places to use it for car washing
The quality of the brushes is good and distinct from the $100 Shop products
View detail
It should come with the product
It is used to paste Rim stripe on MT-07
This product is a must as it is difficult to apply cleanly with FreeHand
But I've put it up a few times and I always think about it You could have included it with Rim stripe
I think most people are new to pasting, so I think it's kind of nice to include it in the package
(The first time I worked on it, I forgot to buy it and failed to stick it on.)
Even after the second time, if it's an individual, it could be when you buy a new motorcycle, or it could be a few years later It is It seems to be missing such a Small Dice
View detail
It is safe to use
When replacing the spring of the Monoshock, it is necessary to replace the spring compressor with I selected it, but the type that hangs a nail on the spring is a cheap one, but it seems to be unstable We chose this product based on the price and how safe it was to work with, with a lot of imprecisions
Some of the things I liked about the actual work are
Our suspension is a U-shaped bracket type, but the bottom end eye has a U-shaped bracket The width of the Bracket is not wide enough, so the Spring pressure is removed to make the Preload Adjuster easier The other objective of turning it into
PushBolt is a type of belt that can be fastened with a D Ring like a Helmet chinstrap The spring seat does not come off easily even if you tighten the spring seat, and if you look closely, you can see the reaction force of the spring Make a knot on the edge of the Ring as shown in the second picture And it didn't slip any more
You might want to replace it with a Tie Down here
When you tighten the PushBolt for the first time, the suspension body also rotates in the direction of tightening It made contact with the arm part and scratched it
As a countermeasure, while pasting gum tape as a cure to the Arm part of the Compressor I put thicker Sponge rubber in the gap between the body and the suspension body
You need to loosen the Belt every time you repeat the work to fix the belt It feels a bit cumbersome
I wrote various things, but I can replace it without anxiety by just tightening the bolt of 1 pc The goal of not even scratching the Spring (although it did scratch the suspension body) was completely achieved I think it was the right decision to buy it
View detail
Easy to use
Motive for purchasing
I purchased this for the washfor vehicle
Good points
The hair is rather soft and sturdy for scrubbing and Large
Connecting the Hose, etc. allows you to use it while running water directly
What I liked about it
nothing special
It's as easy to use as I expected
View detail
It's cheap!
It is used for Tappet clearance of GORILLAetc.4CycleEngine and I have
The price is low enough to save me a lot of money because I can't use it to measure Clearance because it gets worn out gradually
The gauge is made of a large size, but the gauge is made of a fixed metal clasp GORILLA, it's hard to use for MONKEY, so Size is stamped on it, too, so I'm going to have to make a stop If I remove it and set it to RoseRose, I can use it by shifting the position 4 or 5 times I am!
View detail
Kawasaki Fender Essentials
On Kawasaki FFenders, there is a Rivet stop on the Hose Bracket Fenders are not something you have to replace over and over again, and the price is important I bought it
I was prepared to use it because it was too cheap, but I was able to stop Rivet without any problem Multiple Rivets used in the ZX-6R 2016MODEL Fender are also included Even if you do and fail a few times, you have the peace of mind that you can start over
I still want to stop Rivet as per OEM rather than replace it with Bolt! But if you want to hold down Cost, this is the way to go
He is a good kid who is useful for more than just Motorcycle
View detail
Syringe, which is neither good nor bad
When I replaced the Hose on the Brake, my 4 year old Syringe was in an unusable condition There was also a point, so I bought it
Unexpectedly, the large aperture size of the Horse is large, and the Kawasaki EX-4, or rather the stray car It didn't help much, as it came loose a few times during air removal
Hose is $10cm for each of the hose and $20 for each off-the-shelf corner at Home Center It's about the same, so you can just buy it
View detail
A bit lacking in accurate drilling, but better than nothing
I bought it in a hurry because I really wanted vertical accuracy when drilling in wood
Guide comes with 4mm/5mm/6mm/8mm/10mm/12mm Guide It was also in the imprint of other HP, but Plus Chick Case and Guide are a little bit slow Therefore, you can adjust it by wrapping masking tape around it to make it easier to use
If you want to drill a hole with a diameter other than the guide, you can drill a small hole with the existing guide and then use the guide to make a small hole After that, it is possible to expand the hole diameter by using the drill of the specified size
If you want to drill a hole of 4mm or less in the guide, you need to be creative
We may not be able to accommodate any further accuracy or angle changes that may be required
View detail
It would be nice to have that
I ordered it at the same time as the Rim Sticker, and when I actually did the sticking work, it was very easy to use and It was easy to stick it on
It would be nice if it came standard with the Rim sticker, but it's a Single Item It's hard to buy
View detail
It is an essential item.
When I bought it at the same time as the Rim sticker and used it to install, it was easy to use the Rim sticker I was able to put up the product I'm happy to be able to paste it beautifully without having to worry about alignment
It's a good idea to have a 10?
View detail
It is good as it is not so far.
Because I am made of paper I can not go if I look sweet.
It is pleasant and pleasant as it is strange to use.
If you are not confident, why not try using.
View detail