Reviews
Aluminum Pipe is looking sharp.
I bought a long aluminum pipe for my own parts for CRF250RALLY. I used to cut it with an iron saw, but I think it is better to use SK11's Pipe cutter for clean cutting.
After deciding the length to be cut, use the Magic to mark a point on the Pipe cutter, place the round blade of the Pipe cutter on the point, and lightly tighten the Grip. When the markings are visible, turn the Pipe cutter further. You will feel resistance when you turn it, but when it becomes weaker, the amount of turning will be cut. If you continue to rotate the Pipe cutter, the Pipe cutter will make a horizontal gap, so you will need to increase the depth of the cut by pulling out the round blade further. After cutting, pull out the chamfering blade attached to the body to chamfer the inside of the pipe.
When determining the length of the cut, it is better to make adjustments by considering the thickness of the blade. In the case of an iron saw, the object is cut off with the tip of the blade on a line Image, but with a round blade, Quantity:Pair (for Left and Right) The body has a roller to hold the pipe in place. The body has a roller to hold the pipe in place. If the object is soft aluminum, the roller will leave marks if it is tightened too hard. If the holder of the round blade starts to wobble during use, which is rare, remove the grip cover and tighten the loose screws. The first marking is easy with aluminum, but difficult with steel, and be careful with plating pipe, which is slippery even after marking. The chamfering after the work is simple. The final chamfering should be done with sandpaper or a file or you will get hurt.
This tool is designed for Pipe, but I also use it for cutting and marking aluminum rods with an iron saw. The process is the same, but there is a limit to how far a round blade can cut a round bar. If the marking is on a line, it is easier to apply the cutting edge of the iron saw and fix it in place. In this case, the length of the cut is adjusted with a margin for the tip of the blade.
If you are a beginner, it is difficult to cut a round Pipe cleanly with an iron saw. It depends on the work environment, but it is a good tool to have.
View detail
Recommended for Full Cowl Motorcycle!
Since my car is a Full Cowl, I have used many different Lining Peeled Off Tools to remove the cowl, but this product is very easy to use! I like that the resin used for the handle is different from the material used for the peeled-off part of the gold part! It is quite sturdy and I think it will last for a long time! View detail
Point Utilization
This time, my Point expired, so I bought TapTool, which I had wanted for a long time.
Repairing Bolts and Nuts that have become reluctant due to daily maintenance of cars, motorcycles, and othersMaintenance.
View detail
Easy home welding
[How is it used?
When we restore old vehicles, we find parts that are missing or damaged, and we have wanted a welder for a long time, but we have not been able to get our hands on one.
That's when he encountered Solidly's Bolt and completely licked his head, even breaking the Folding Bolt without tool.
I'll weld Bolt off!" I was so enthusiastic that I bought it with great enthusiasm.
Was the one you received as per Image?
Usually Quantity:Non-gas mild steel wire, tip, and leather gloves at the same price as the Set.:I was looking for a set of items, but I couldn't find a Tip anywhere.
I looked between the cushioning material and inside the product, and the Wire and leather gloves were indeed included, but only the Tip was missing. Well, such a trivial matter is fine.
How was your experience with it?
Doing the welding yourself. (almost) First time.
Since I had watched from nearby many times from preparation, I was able to start welding without any hesitation by following the included instructions.
I was impressed even before I started using it, partly because the instructions are easy to understand, but also because the structure is very easy to understand.
We tested the welding with an appropriate steel plate and went to work. Although the welding was done in a very amateurish manner, we were able to safely weld the bolt together and remove the bolt.
It took 30 minutes from the start of preparation to the removal of Bolt by an amateur. This is amazing.
Since it is semi-automatic welding, one hand is free to do some holding.
Moreover, the Breaker did not drop out of the 100V power supply at home, and there were no problems at all with operation.
[Points to note]
Welding can be easily done at home, but of course it is a dangerous process and requires solid knowledge.
The opening photo was taken indoors, but of course work in a place where Garageetc. will not spread the fire.
Fireproof sheets are also needed to cover the shaded surfaces and surroundings.
How did it compare to other products?
I have rented equipment and had a little experience with 200V semi-automatic welding, but it seemed to me that there was no difference.
I think I'm just a novice and can't tell much difference.
【Review】
It is insanely easy to weld at home, comes with Wire and leather gloves, and is very affordable.
As a welder that can be used at home, I give it a perfect score of 100! The only regret I have is that it did not include a Tip, so I gave it 4 stars! (Lol)
View detail
Fog Lamp
I was attracted by the angular design, which is rare nowadays, as most of them are round.
I have used it as a Fog Lamp on my Ninja 250SL after small modification. The brightness is enough and the waterproof property is perfect, so it is a recommendation! We are planning to install it on a light truck as well!
View detail
peeling off
I purchased this product in the hope that it could be used to remove Packing, Rubber, and Sealants.
The tip of the blade is a size and both tips are taper shaped, so it seems to be good for use.
View detail
It can be used normally
Four types of Rivet are included, even for beginners.
Four types of Nose peas are also included.
Of course, you can Rivet properly.
There are expensive products, but this is enough for amateurs.
View detail
Fits: その他 Universal, その他 Universal
The length is good and ideal for Tappet adjustment!
I wanted to adjust Tappet and could not find Thickness Gauge, so I had to buy a new one!
I was looking for something as long as possible and easy to use with a small number of sheets, and I found what I was looking for!
Even in narrow and hard-to-access places, it makes the most of its length and bend to make a quick and easy decision!
My favorite
View detail
Purchase by wash for Vehicle途
[How is it used?
I bought it from Wheel Wash for Vehicle.
Was the one you received as per Image?
I use it on my motorcycle and car, and it lifts dirt well in both applications.
How was your experience with it?
However, it is not good at cleaning fine or deep areas, so it was used to wash surfaces in large quantities.
View detail
Great for Better Alignment
he alignment marks on my swing arm aren't even close to setting my wheel in alignment with my sprocket and chain. Pretty simple tool for more piece of mind when doing chain adjustments. Works well on my bikes. I put the tool on just to see if my current alignment was good. It is, but the tool confirmed my suspicion that the alignment marks on my swing arm are not stamped symmetrically. I eyeballed it prior to purchasing this tool. If you have calibrated eyesight, an alignment tool isn?t really necessary. But, this is an affordable and useful little device to make the job a tad easier. Would be better if the metal rod was longer.This tool is essential to minimize chain, sprocket wear, and noise. It is kind of a pain to use as you need to remove the chain card to enable setting this up. But once done, my ride is much quieter.If you have deep pockets, I imagine the laser alignment tools would be the way to go.Fast shipping as always too.It comes in a big box, I don't think it's necessary. I want economical shipping.That's why shipping is expensive and subject to extra inspection at customs. View detail
Too big, mostly for Wheel
[How is it used?
For undercarriage wash of Motorcycle
Was the one you received as per Image?
It is so much bigger than I imagined. It looks like the size of a car wheel brush. It has a Size feeling like a Brush for a wheel of a car.
How was your experience with it?
It is indeed flexible, but I think it is too big and not suitable for washing motorcycles. If it were half the size, it would be easier to wash the area around the rear shock and around the engine through the cowling, but I don't want to accidentally damage the paint with it.
It would be good for something like NAKED with an air-cooled engine.
[Points to note]
The bristles are too hard to wash painted surfaces, so it is mostly used around the feet and engine area.
[Opinions and requests to Manufacturer
Put it out half as fine as it already is.
View detail
Spring Mounted Hook
It is used for spring removal and attachment of the Exhaust System.
The price is reasonable, and it can certainly be made Compact since it can be split in two.
It is not used that often, but it is good to have 1 pc. to take the spring on and off for maintenance.
View detail
Spring hook
It is used for spring removal and attachment of the Exhaust System.
The Type is a little long, so it seems to be easy to apply force when pulling, but in some places the long length gets in the way and makes it hard to work with.
It is good that it can be split into two parts, can be removed, and can be pulled by swinging it at an angle, but it turns too much and cannot be pulled properly, making it difficult to install the spring hook.
View detail
Don't scratch it.
I purchased this tool for a different purpose than its original use, such as removing parts attached to resinous materials, where I don't want to scratch the surface.
It is resin, so it is not that strong, but it seems to be good for use to remove it by placing it in a gap without much force. The surface is covered with silicon rubber, which is also resilient and helps prevent scratches.
Since the price is not that much, you can give up even if it breaks after a certain amount of use.
View detail
Exchange for Refresh
I bought a used ZZr, a motorcycle that probably hasn't had its suspension linkage greased in 26 years.
It can be used normally, but the cap seems to come off easily.
View detail
To remove Cowl!
This is an essential item for Cowl removal. It is recommended to apply grease to the joint part for the next time after the cowl is removed. View detail
Spare
I purchased Body to remove plastic polish, scratches, and dirt from cowl and screen parts, but I thought that Included Parts:alone would soon be ruined, so I purchased this Spare.
I wanted only the replacement Buffing.
Brush is not used very often, so it was unnecessary, but Quantity:It is a Set, so there is no choice,
View detail
Cut
The price is not that much, and it has a good feeling of ease of use.
The handlebar is large, easy to grip, and easy to apply force.
It is also nice to be able to change the position of the blade with Slide.
View detail
easy to grasp
The Grip section is thicker for a stable grip. View detail
Rim stripe easily affixed
Used for Rim stripe installation on YZF-R6 (2019).
When used for water pasting, Rim stripe can be applied quite accurately and effortlessly.
Some adjustment may be necessary where the rim stripe overlaps.
It is also Large cut to paste with Image to push out air bubbles. Removing air bubbles afterwards is also Large cut.
View detail