Reviews
I think it's cheap
Personally, I thought it was inexpensive.
It feels good to use, polishes properly, and is convenient to have.
I would buy it again.
View detail
Versatile Holding Tool for your Maintenance Needs
About quality and texture: I am happy with the quality of the band holder from ProTools, made from a steel construction with a PVC coating over the band to help improve it's hold. About the feeling of use: I have used this tool to hold the clutch and flywheel on my Honda Grom when removal of these parts were required for maintenance with great success. The adjustable band makes this tool very versatile for varies sized motorcycle parts. Products to buy together: Some more tooling like a center lock nut wrench would also be desirable to purchase along side the band holder so when it comes time to remove the clutch assembly and oil spinner on your Honda Grom you have all the special tooling required to complete the job. Difficulty of installation: The process to install takes a few minutes, place the band holder around the part that needs to be held and adjust the band if required. Tighten down the T handle so that the band holder does not allow the part to spin as you undo the fastener securing the part. Not difficult to do. Cost performance and comparison with other products: Good costing as this is a quality made band holder from ProTools that has with stood numerous usage without failure as compared to the first band hold that I purchased from another site that failed soon after. About shipping and packaging: The faster shipping options are too expensive for myself so I just have to wait for my part to arrive via sea freight. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: These band holder are limited to the sized parts they can hold. No smaller the 6cm in diameter and no larger then 12cm in diameter. View detail
Easy to use
Not bad
Spring can be conveniently installed and removed.
It is strong and will not break even if it is used for strong springs, so it can be used for exhaust springs and side stand springs.
It is safe to use
View detail
Useful for more than just Motorcycle!
[How is it used?
My boss at work had one and lent it to me once, and when I picked up something in a tight spot, I decided to buy it.
I immediately bought one myself and am using it.
How was your experience with it?
When stored, it is compact and unobtrusive, but when extended, it is quite long and can pick up objects at a distance.
One item is useful not only when servicing your motorcycle, but also in everyday life.
The tip is Magnet, so it is versatile enough to be attached and picked up, or hooked and picked up.
This is one product I wish I had known existed and bought earlier.
It is inexpensive, so it is useful to keep it in your tool box in case of emergency.
View detail
Nice to have one!
It is a useful tool for various Situations, such as when repairing objects that have fallen into gaps between vehicles or rolled under furniture.
It is not expensive, so it is very useful to have one in your tool box. other than motorcycle maintenance, it is also very useful for retrieving items that have fallen through the cracks in your desk, or for pulling up LANCable or Outlet.
It is really useful, so please buy one.
View detail
It is convenient to have it in Maintenance of Clutch type !!
Purchase for exchange of Clutch Spring of CYGNUS X SR 1YP.
It is convenient to have it when Belt drops in.
When exchanging Center spring and Clutch Spring
With or without a thing, the feeling of tiredness of the finger is completely different.
If there is one, I will recommend it as something useful.
View detail
To drive and remove Wheel Balance Weight
PROTOOLSBalance Weight Hammer is used for Tire exchange to remove OEM's driven balance weight.
Because it is for Motorcycle, since the width of the part that grabs the weight is about 2 cm and it is Small, it is easy to use.
Weighing measured at 436 g, there was a response, Grip's Red Vinyl Cover also slid and gripped feeling well.
Also, on the Grip side of Joint, there is a blade that can cut pasted Plate Weight.
The part of Hammer that drives Weight has a rounded and bulged shape from the center, and it is considered that it is hard to scratch the surrounding Wheel when driving Weight.
The other day, we used ZYR 1400 Tire to remove Weight when exchanging, Balance was pasted Weight.
However, the weight attached to Rim stands out (It may be a matter of concern) Since it can not be helped, I am planning to change it to the driving weight of the OEM soon.
Personally, it is very useful.
View detail
Carelessly, is a Piston Circlip dropped into a Crankcase and aren't those who were troubled? It is an ironbound rule of maintenance to fill a Dustcloth in a Crankcase so that the Circlip may not be dropped, but.A Dustcloth flies by a wind during a break,
Carelessly, is a Piston Circlip dropped into a Crankcase and aren't those who were troubled? It is an ironbound rule of maintenance to fill a Dustcloth in a Crankcase so that the Circlip may not be dropped, but.A Dustcloth flies by a wind during a break, he does not notice that, but work is done, a Circlip is dropped to a Crankcase, and it has the bitter experience I got the Shop to help (it does not come out, even if it uses reverse!).At the Shop, it picked up by the same thing as this product.
It came to purchase taking advantage of it.
Although it is not a thing used so frequently, it is wiser to have not been a high thing, and considering the difficulties which carry an Engine to a Shop, to have.
View detail
Although he thinks that it is a major tool at the time of muffler exchange, it can use for others. It is exchange of a brake pedal. The powerful return spring also attaches the brake pedal, after attaching a pedal to a bracket, it is necessary to
Although he thinks that it is a major tool at the time of muffler exchange, it can use for others.
It is exchange of a brake pedal.
The powerful return spring also attaches the brake pedal, after attaching a pedal to a bracket, it is necessary to put a return spring but, and since this is powerful, it does not fit in easily.
To the panel of having fought as the half an hour to attach to a hook point so that it might hook and let it sliding in a slotted screwdriver, but not fitting in easily but cutting a fingertip with the point of a spring roughly conversely.
For the time being, the injury was written, and he gave up wearing of a spring, and has seen and realized this spring hook right away in a net on that day in the evening.
! comfortably inserted in if it is this.
After goods arrive the next weekend (a fingertip is also recovered mostly completely), when re-challenging by this spring hook, it is the completion of wearing at one shot!
A complete change is undergone with it having fought desperately and been injured and having been defeated last time, and it is this simplicity.
He keenly realized the importance of the special tool thoroughly.
There are also a return spring of a brake and a spring of side stands and a center stand in a motorcycle in addition to the muffler spring of an external article.
Since especially the spring of a stand is powerful, if it is going to pry and put in with a driver etc., a possibility of carrying out a severe injury to a fingertip will become very high.
For that reason, if the tool box is made to bear this tool, also when such, it can solve easily immediately.
Although it is a rarely used tool, in a cheap and required scene, those who tamper with a motorcycle by themselves recommend you strongly to put into a tool box by all means for a very important tool.
View detail