Reviews
no problem
There were no problems, and the product could be used normally. View detail
historical legacy
Wow, so many people writing imprements on just Nozzle!
When I was on my 2nd, I kept a 1 liter can at the fueling port in the back of the car. Replenishment." The best time to do this was when I was
We didn't weigh the Levels exactly, and it was routine to dispose of the entire can after 3 or 4 refills (and it was free back then).
On the other hand, when pouring more than 3Liter in 4st Engine oil change, there is not much Merit.
It would be much faster to transfer the required amount to a jug or use Bellows long funnel...
But there is something quaint about attaching it to the mouth of the G1 one at a time and waiting for the last drop to fall out.
I think it is a gem that has supported Sunday Motorcycle.
View detail
Nozzle
I think the product is good.
I changed the engine oil for the first time in about 10 years.
I was very enthusiastic, but the oil leaked out of the BWS125 because the place where the engine oil is put in is at an angle.
Next time I will use Funnel. But my hands get dirty too, so I may leave it to Shop.
View detail
Necessities when changing Oil
This is the first time I have used this product, and it is a convenient product that fits tightly into the mouth of Honda's UltraG1 and can be disposed of as is.
However, if the engine is a Vertical TypeEngine and refueling is done from above, the nozzle part is a little short, and there were times when the oil would spill unless the kick pedal was removed on my vehicle.
I would be more than happy to have a longer Nozzle as a separate Spec.
View detail
Cheap Oil nozzle
If oil is poured directly into a motorcycle, there is a risk of spilling it, so it is safe to add a nozzle.
I bought this product because it was recommended to me. There is nothing special about it, but I think it is a product that can be recommended to everyone because it is inexpensive and has no problems in use.
View detail
Used in Oil Replacement
The product is as good as it looks.
Basically, OEM type Oils do not have Nozzles on the Bottle portion, so we use them in that case.
It is neither particularly good nor bad.
As others have said, it seems expensive to say it is expensive.
View detail
Nozle at the time of oil injection
I think it comes with the Oil when you buy it, but if you don't have it when you pour, you spill it, and if you wipe it clean after use, you can use it quite well. In terms of selling price, it's a bit pricey. View detail
Required for Oil replacement!
[How is it used?
I use this when I change the oil in my Scooter! I had to cut a dry plastic bottle to pour the oil, but it was a hassle, so I bought this product. I am glad that it became easy.
How was your experience with it?
Of course it is easy to use. It is a common Nozzle? I would appreciate it if you could put it with the Oil when you buy it. It gets sticky after one use, so I think if you wash it thoroughly and store it, you can use it again.
How did it compare to other products?
I felt there was not that much difference. I think they are the same.
Might as well buy them together when you exchange Oil!
[Points to note]
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
Easy to use
It was very easy to use. I just don't know if I'll be able to store it. View detail
I wish they were a little cheaper…
Title is right I think probably all Users who bought this product agree with me lol.
I am a Rider who does not make any discovery, so this is my rating.
I bought it last year and have just used it and have no problems using it.
View detail
Unexpectedly easy to lose
[How is it used?
When I buy Oil, I find myself buying it together.
It can be used many times, but after using it once, I am very prone to losing it.
Made in foreign countries (A little expensive) Plastic containers that are a bit nifty have nozzles at the mouth, but many Japanese tin plate cans, such as OEMOil, do not. You will need such a nozzle.
How was your experience with it?
Basically, it can be used for 1L tin plate cans, whether Honda, SEA BASS, or Yamalube, since the tin plate can itself is almost the same.
If the oil inlet protrudes from the outside, this is sufficient, but if the oil inlet is located a little further back, such as on a scooter, or if the inlet is extremely narrow, as on some off-road motorcycles, a gardening funnel or narrow-necked Sprinkling can is easy to use.
How did it compare to other products?
First, it is”by far”easier” than pouring directly without anything. Pouring without anything usually results in spillage and contamination of the Engine. The dirt on the dripping oil is disastrous.
Plastic funnels are available at 100-yen stores, but once you use one, you have to wash it again or use different types of oil, so it is better to have several disposable funnels. It might be a good idea to buy 10 or so in bulk since they are inexpensive.
[Points to note]
It is easy to lose it. I really don't know where it went. (Is it just me?)
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
I think the Timing I will use is when I change the Oil, so this is the area I would like to buy with it at that time.
Oil Disposal Box 4.5L Work GlovesQuantity:Set
https://www.webike.net/sd/21779950/
→Nitrile gloves are Quantities:The set is the main point. 4.5L is enough for 2-4 oil changes in Motorcycle.
Tear-resistant paper towel
https://www.webike.net/sd/24985573/
→Paper waste is definitely the way to go. I really recommend this one because it is tear resistant and can be used all the time.
View detail
I was having a hard time finding it for sale.
I use it for 1LOil cans of KAWSAKI.
I bought them in bulk because they are hard to find.
I had to go to the trouble of replacing it with Oil Jug because it does not come with it when you buy it on the Net, but from now on, the hassle will be eliminated.
View detail
I want it on from the beginning.
[How is it used?
Used for pouring Brake fluid.
How was your experience with it?
Pouring can be done without spilling.
In the case of a large scale, it is difficult to work without this product because the brake fluid is hard to pour.
If you want careful work, I would love to have it.
I would like to see it included with the product if possible.
View detail
if possible
I would like it to be attached by Service when I purchase Oil. View detail
It can be used normally
Used to be in the Oil department. Feel free to bring your own." I used to have it in my office, but I don't see it anymore. If you don't have it, you can live without it, but if you do have it, it makes your work a little easier.
This was the first time I paid for this product, but I was able to work with it without any spillage of oil on the mouth of the can.
View detail
Exactly
It is Exactly on the Screw part of the oil can and was comfortable to use without any oozing. View detail
A necessity for Oil replacement.
This is all you need to replace the oil yourself.
It is useful because it can be used repeatedly.
View detail
Not required, but
It is possible to inject oils without it, but it would be much easier if it were available.
It's insurance to avoid the tragedy of smashing the car body or floor.
View detail
Required for 1Liter cans
I use it all the time when changing Oil in 1Liter cans.
The angle of the spout can be conveniently adjusted with the bellows.
(It used to be included as a service when you bought Oil, but now you have to buy it separately.)
View detail
Nozzle size should be selectable.
I used it for refueling oil for my Honda GR2's 1L cans. The screw type attachment to the oil cans allows for secure attachment and no oil leakage during refueling. Nozzle angle can be changed. When removing the nozzle from the can, a little bit of oil from Bellows leaks out, so I thought it would be better to use Dustclothetc. to remove it. The size of the nozzle and the amount of oil poured into the nozzle will vary depending on the situation, so it would be useful to have an attachment etc. that can change the diameter of the nozzle when refueling directly with this nozzle. View detail