Reviews
Probably shoddy
I was able to use it, but the bearing assembly of the rotating part is not right.
The rotation at the time of jack-up is terribly heavy because of it.
As delivered, the grease of the moving parts was dirty and covered with iron powder and dust,
I took it all apart and Greased it up again before using it.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
cb1100RS MORIWAKIShort Tube without Center Stand
When using cb1100RSMORIWAKIShort Tubewithout Center Stand, the exhaust system will be interfered if the longer attachment is not used. In the side stand condition, the jack with the longer attachment will not fit, so it is a bit dangerous to put the jack in the right position while raising the motorcycle by yourself. It is not recommended to use it in the same way as I do, because the positioning is very troublesome. View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Cospa best
I was able to lift my heavy BMW K1200RS without any problem. It is very stable and the cost performance is great.
It is quite heavy, but I think that contributes to its stabilization.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
ChainMaintenance is now easier.
In the past, chain maintenance was done with the rear wheels on the roller stand, but the parking lot is slightly sloped and the rear wheels would gap from the standenter as they were being turned, making it very hard work.
This Lift made ChainMaintenance a breeze!
It is for use on a DragStar 250. When I received the product and saw it, I wondered if it would fit under the frame. But it went in without any difficulty.
The price is reasonable and the product itself is solid.
This was a good purchase.
View detail
Should have purchased this earlier!
[How is it used?
For Motorcycle maintenance
Was the one you received as per Image?
Yes, there is one paint peeling, but it is a CHINA Level product, so I'll just ignore it.
How was your experience with it?
More stable than expected.
[Included Parts:were they on?
JackAttachment is two kinds
[Was there anything that disappointed you?
I don't expect much from CHINA products.
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Axle Shaft insertion is by far the easiest
I used it to remove and install 1200CX Front wheel.
I had considered a very inexpensive STANDJACK similar to this product, but many other reviewers had criticized it for its lack of rigidity, etc., so I decided to purchase it from the trusted Webig.
I have been using Pantograph jacks, so the stability of the car body during jack-up is completely different, and I can start work without worrying about work accidents.
It should be noted that I can now easily insert the Axle Shaft of the front wheel, which I had difficulty with before.
I wish I had bought it earlier because it can be used not only for DoubleCradleFrame but also for Twin spar frame cars.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
sense of stability
It can be used effectively for motorcycles without a center stand.
They easily lifted the heavy body of the vehicle.
The work in general, including the replacement of the rear suspension, was done smoothly.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Excellent stability
It can be used effectively for motorcycles without a center stand. The long adapter supplied with the kit was a little short, so I lifted it up by myself, but it lifted up the heavy body easily. View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
To Lift up Motorcycle
[How is it used?
The Frame of the TZr250R I purchased had a bend in it, so I used it to replace the Frame.
Was the one you received as per Image?
It's a Chinese product, and I've seen it on various shopping sites, but I don't use it often enough, so it's good enough for me.
It came with an instruction manual for the English version of the Perraich. You can use it as soon as you receive it.
As everyone has written, it is much heavier than it looks, and moving it around is quite large and strange.
How was your experience with it?
I used it to support the car body by putting it under the Engine.
It can be raised and lowered by turning the lever attached to it, and it moves smoothly without requiring any special effort.
The paint is thin, so after one use, some of the red paint on the top panel was scraped off, but if you don't mind the look, it's not a problem in actual use.
I was able to use it without any trouble.
[Points to note]
The support part at the end of the Arm can be turned freely, but it cannot be fixed, so there is a risk of it falling over if you don't make sure the load is firmly applied.
How did it compare to other products?
I considered the one without Arm, the one with Caster that can be moved, etc., but I chose this product because it comes with Arm and seems to have a high degree of flexibility in fixing.
【Review】
It also comes with an Arm, which is useful for supporting an unstable motorcycle engine, and I think it can support a large motorcycle.
If you are a Type who does all the maintenance yourself, it would be convenient to have 1pc.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Cheap enough.
It's not a frequently used item, so I thought an inexpensive one would be OK.
The construction is rough, but it's not something that will break because of it, so it's enough for those who are not particular.
I'm very happy with it.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
It's cheap and enough for what you need.
I bought this for maintenance around the Rear of my MONKEY125.
Quantity:Pair (for Left and Right) The position in the direction can be moved freely, and the height can be set to Quantity:Pair (for Left and Right) This can be adjusted to some extent with the
It's solid for the price and has a decent weight and stability.
If you have a heavy vehicle, you may be worried about the stability, but it was the best buy for my 100kg MONKEY.
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
I'm using it on my Z125PRO!
It's the same for Z125PRO to be able to change the sprocket and fork oil I bought the Minimoto MONKEY, DAX compatible
The body weighs 15kg, so the sense of stability when working is good, but it is not easy to hold and it is not easy to set the position That's Neck
(Be careful not to do your back …)
It can be purchased for less than 10,000 yen, and although it is heavy, it can be stored comparatively in Compact, which expands the scope of maintenance I think it's a good product because it gave me a good idea
By the way, if you want to raise the front wheel on the Z125PRO, you should remove the Under Cover It is
When raising the Rear, you can do so at the base of the footpeg
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Expanded Maintenance
I bought it to learn maintenance of my Motorcycle I mainly touched the front area and link type Mono Suspension area The Jack itself is quite heavy (15kg!) to accommodate motorcycles of all weights I am generally satisfied with the results
In order to remove the front fork, it is necessary to raise the front area The famous Front stand is expensive, and this one, which can even cover the work of keeping the rear afloat I chose Jack I have felt the usefulness of the dedicated STAND with the Rear stand, so I will buy it sooner or later It is
My motorcycle is a Full Cowl, so to use Jack, I have to use Under The removal of the Cowl is essential, as it is a 4 cylinder engine, and it is necessary to remove the Cowl from the exhaust pipe assembly I wasn't sure if I could hang the jack tightly, but I put the exhaust pipe between the jack and I was able to support and jack-up the oil pan DoubleCradleFrame's Motorcycle would be more stable because you can bite Jack here
The arms come in two types, long and short, depending on the type of motorcycle and how it is supported It's nice to be able to use it differently It seems to work fine on my other motorcycles as well
It's not as SMART as it should be, but it's definitely jacked up and the price is reasonable, so I'm glad I bought it Hey
View detail