Reviews
Is good
The Chromium Plating process is highly accurate and resistant to Rust.
I use it to measure all kinds of Parts and have no institutional problems.
This Caliper is very easy to use due to its low rattling.
View detail
Convenient
You can check the battery status.
You can easily check it by simply inserting it into the Cigar lighter socket when Ignition is ON.
It is easy and not difficult.
View detail
For tightening of Drain and Plug
I have a SK11 Digital type, but I like the snap sound of Analog.
I was looking for a low Torque for tightening the Drain and Plug as per Title.
The main thing that attracted me was the colored text part, which made it easy to read.
View detail
Koso was meter red
This time I am going to fix in my car for checking voltage. After long time finally I found the correct size for my suitable place . The real time voltage as a multimeter show up and low voltage/high voltage warning also working perfectly (check it test bench) I'm recommending to who are like to work and update gadgets enthusiasts. View detail
Easy to use
The Inspection Tester is very useful for locating a permanent power source.
The LEDs light up for easy and safe use.
View detail
Easy to use
I used to tighten it properly when changing oil, but with this product, I can now manage the torque tightly. It is easy to use and there are no problems. View detail
Highly reliable
I bought it because it is necessary when tightening a motorcycle rear axle or other large torques.
The measurement range is also wide, so most things can be covered with this.
You can also set the measurement value by simply turning the Handlebar behind it.
The click feeling in that case is also easy to understand and the scale is easy to read.
Workability is high.
Since it is Tohnichi, the reliability of the measured values is high, and although it may need to be calibrated at some frequency, I believe it can be used for a long time.
One drawback is that the measured value is not available in the Quantity:I lock it with the knob behind the Handlebar when I set it.
Even if this is not tightened very hard when locked, it takes so much force that it hurts the hand when loosening it after measurement.
If only this point could be improved, I would have no complaints.
View detail
In addition to leather
I first bought it to poke holes in leather.
Now I use it to drill holes in everything.
I use it to put on Eyelet.
It is convenient because the hole will open as soon as you hit it with Hammer.
I think it is durable because the sharpness lasts for a long time.
View detail
Easy to use
The tip is sharp, and a light tap is all that is needed to firmly attach the mark.
If the Mark is shifted, the Drill hole will also be Large.
This product is very accurate and helpful.
Once you buy one, you won't be replacing it.
It is better to buy a good one from the beginning.
I can recommend this product.
View detail
I wonder how many years I've been using it.
Ah. You're in the picture (laughs) Torque wrench.
How many years have you been using it (laughs)?
I didn't make any corrections or anything like that.
I think the accuracy is hardly crazy.
I use it infrequently (laughs).
When I put together the four-wheel Engine.
And I use another KTC Torque wrench.
Well, it is better to tighten the major parts with Torque wrench. It is safer.
View detail
Precision
I bought the Torque wrench because the accuracy of a certain PROducts Torque wrench was obviously not right. However, with sk11's Torque wrench, the "snap" sound is not so clear, but it can be heard normally, so it can be used normally. It is very rare to find a Torque wrench that can be used in a normal way. I think it is a very large thing to be able to use it normally. View detail
Large strange
I have used it on 3 motorcycles and 1 car and it has not broken when used on motorcycles and my car has been through 2 mid-summer and it has not broken at all. The waterproof treatment is very clean and the product itself is solid, not cheap. Wiring is also very easy, so I highly recommend it. View detail
Necessities
This is a change from the pre-set Digital ratchet.
I usually use it for replacement work up to M12-size bolt.
The most important feature of the Large is the sound that warns you when you approach the specified Torque.
With the pre-set system, I don't know how much more I need to tighten because I don't know what the current tightening force is, but with the Digital ratchet, it shows the progress so I can adjust the amount of force. With Digital ratchet, the progress is displayed, so you can adjust the amount of force you apply.
The torque is also displayed when loosening the bolt, so if you are removing a bolt with an unknown torque, you can use Digital ratchet to loosen it and find out the tightening torque. Of course, this is not the case if the bolt is sticking, but I tried it on another bolt and found it to be surprisingly accurate.
I send it out for calibration every year, and it is hardly crazy, and I think its durability is good.
Also, in the case of the pre-set formula, the gap between the largest and smallest acceptable values becomes large due to its structure, but in the case of digital ratchet, there is almost no error even at the smallest and largest values.
It is also repairable, so it is still in use even though it has been dropped into a waste oil receptacle in the four years I have been using it.
View detail
A feeling of raising the level of motorcycle tinkering
When I first started tinkering with motorcycles, I didn't understand the importance of torque management, but after experiencing many failures, I learned the importance of large. I feel that I have grown up to be able to use my gold to keep my motorcycle in good condition, rather than spending it on customization. I've used other manufacturers' torque wrenches, but the KTC is the best for me because the memory is easy to read, the controls are nice, and it looks cool. View detail
staple goods
I was thinking of choosing Tonichi or KTC, but KTC's delivery was faster, so I chose this one.
Of course, there was no particular quality problem.
View detail
More peace of mind at this price!
In the winter, I was concerned about the battery voltage because I wear electrically heated Wear.
Since it is a Liter machine, I don't think I need to worry about it so much, but since it is invisible, I am a little worried.
It's not expensive, so I installed it as a DIY project.
I have a DUnit set up, so I just need to connect the acc wires from there to the battery. The installation itself can be done in 10 minutes. In order to hide the wires, I removed the cowl and put it under the tank, and struggled for about an hour.
The three wires from the power supply are thin and RoseRose (not bundled into one pc), so I used Vinyl Tape to tie them together. If I don't, I'm worried that they might break under the tank.
I used Surface Fastener to place it near the meter, and it's compact and fits well.
Now that I can visually check the voltage, I feel more secure.
View detail
I knew I had to at least do an air check myself.
Since I have nitrogen filling, I usually have my air check done when I go to the shop.
But if I don't have to go for a while, I'll just go for it. It was still almost gone. There were times when I felt sorry when people said, "I'm sorry.
I would forget when I got it filled, and I thought I should at least check it at home, so I bought it.
This air gauge is easy to measure even with a front double disk, because the instrument is easy to read and the hose is long.
The Hose is also made of Gold MeshMaterial, so it seems to be durable.
I haven't compared it with other instruments, so I don't know the reliability or error of the values, but it is a reliable manufacturer's product and I think it is large and durable.
From now on, I will check it myself from time to time and get it filled at the Shop when it is low.
View detail
JAPAN!!
When I say Tor Crunch, I mean Tonichi.
I think it's a safe and reliable Torque wrench!
In addition to motorcycle maintenance, they are also active in car maintenance.
View detail
good
It is large and can be used for changing tires on cars. It is not suitable for engine work. View detail
Small and can be installed anywhere.
I have installed them on all my cars. It is easy to install, just connect the 3 wires to the designated points, the back light comes on, and it is small but easy to see. View detail