Reviews
I can rely on them in times of need!
The Bolt of the Brake Caliper was rusted, so it was Refreshed with KITACOConvenienceParts (M8×40 P1.25).
The Caliper used is a YamahaOEMbrembo.
Since I could not search the OEM Parts List (no parts appeared), I first tried to remove one from Caliper, measured the Bolt size standard with Caliper, and then searched and purchased the Bolt with WeBig.
The torque for installation was measured beforehand with a KTC digital ratchet and was approximately 50 Nm, so it was tightened accordingly.
KITACOConvenienceParts is a great help when you have an itch or need help.
It's just a small part, but I'm glad it's clean!
View detail
Recommended!
Recommended!
Custom feeling goes up!
View detail
It stands out
It's just a Bolt, but it's beautiful and stands out. View detail
casually stylish
Casual Titanium One point
I think it is a good Design.
But the price is high.
View detail
One point
I used it for One point around Handlebar. It is a completely self-sufficient part. View detail
Firmly usable
[How is it used?
I used it when I changed the Silencer on my YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86.
The Φ14 thinner Silencer band is now farther away and cannot be handled by the existing Bolt.
We measured the amount of gap and decided to put aluminum collars on the rear suspension and silencer band side to fix them in place.
How was your experience with it?
The measurements were perfect and firmly fixed.
I have also done a good job of Torque management, so I don't think there will be any problems.
How did it compare to other products?
This time I bought 80mm and 50mm.
Home center also sells Bolt, but basically they don't sell P1.25, so you have to buy it at motorcycle supply stores or on the webike.
I think it's good
[Points to note]
Aluminum is surprisingly soft.
Be careful when working with Overtorque, as it can easily be severed when tightened with Overtorque.
View detail
Self-satisfaction
It is just self-satisfaction.
Still, it is more than enough.
View detail
Beautiful construction
Shape not available in Homsen, used for the exterior of Meter visor. View detail
![PREMIUM ZONE Cap boltCollar [for M8 Bolt].](https://img.webike-cdn.net/catalogue/images/15903/91926_1_TS.jpg)
I like the MATCH feeling with the car body color.
The Multi Bar Holder for GSX-R125 made by DAYTONA has been installed.
The standard cap color was silver, which was a little uncomfortable, but when we replaced it with this product's blue position, it matched the color of the car body and increased the OEM feel.
Although the product does not change its effect in any way just because it is exchanged, we recommend the Large change for those who want to enjoy fashion.
View detail
Titanium Bolt
I am very happy with the new look. It would be better if it didn't fade……. View detail
Black stainless
The Fixing Screw is replaced with this stainless black one to make it less conspicuous, since a regular stainless steel one would stand out.
It was helpful to have a choice of Size and type.
View detail
Fixing Screw
I bought it to try it out, wondering if it could be used to fix Cowl. The materialAluminum was nice, but the tapping screw and the length of the screw seem to limit its use.
It would be helpful if you could sell regular Screws, available in a choice of lengths.
View detail
Black
The Black bracket and Silver Fixing Screw stand out, so I bought it to unify them with Black.
Stainless Steel's Black, I couldn't find a place near me that had it, so it was a great help.
View detail
Stainless Steel Fixation
Fixing Screw to be rust resistantMaterial:Replacement with Stainless Steel.
It helps that I can choose the Size I want.
View detail
High-precision Bolt for peace of mind.
CT125 (JA65) The OEM is a flange bolt, but for some reason, Mukawa's Super oil pump is installed with a hex cap bolt. Since there is a specified torque, we purchased this bolt so that we can manage the torque precisely. The high precision of the bolt can be seen at a glance, and it even has a hole machined for a wire lock. Of course, I will not use the wire lock for this purpose (laugh), but I mistakenly read the description of the product and purchased 3 sets, but I will keep the extra Bolts in case I need another Bolt of the same size, and I plan to transfer them to my friend's CT125 friends. When I need another Bolt in a different size, I will get it from this brand. View detail
![PREMIUM ZONE Cap boltCollar [for M8 Bolt].](https://img.webike-cdn.net/catalogue/images/15903/91928_1_TS.jpg)
When you want to make the Bolt area look just a little bit better.
[How is it used? Restore&maintain a vehicle that was purchased used.
I was working on improving the appearance of the Rear Carrier and purchased this product because the bolt used to install the Rear Carrier looked like a commercial bolt and was not very tasty.
Did you receive the item as per the Image?
It was very helpful because it is hard to find a product that is compatible with M8Size Bolt.
It is a product that has nothing to do with performance, but I feel that the humble part that was just fixing the parts to the car body has become a little more glamorous (I guess it's just the person installing it...) It was just like the Image product.
Was it difficult to install?
It is a totally simple process.
Just clamp it between Bolt like Spacer or Washer and tighten it, and it will also serve as a Washer substitute and look better.
It is also good to be able to dress-up casually.
How did you like it?
As I said above. "No performance-enhancing parts." It does not improve power or fuel efficiency, but it does make the surroundings a little more festive, and that is all that is needed.
Was "Included Parts:" attached?
None, Anodized Treated Aluminum Collar is Quantity:2pc. It is a Simple product that contains only a Set.
Were there any disappointments?
The product was as expected, which is sufficient since I bought it for the purpose mentioned above.
Other items that would be helpful
Point and hang of installation
Install an aluminum collar of the color of your choice on the bolt where it does not interfere with driving.
It is up to the rider to decide whether to have one point or all available Bolts in one color, or to install a variety of colors (of course). Not used." Hang depends on the rider's Sense.
[Availability and clarity of the Instruction Manual
There is no Instruction Manual, it is just easy to figure out by inserting the cap bolt into the area where it is used, so I don't think there will be any problem.
[Notes]
Since this is an aluminum collar for a cap bolt, if the bolt you want to install is not a cap bolt, you will need to purchase a cap bolt with the same diameter, screw pitch, and length as the original bolt separately.
[ITEMS TO BUY TOGETHER
Cap bolt as described above is required.
As a reminder Home center system Bolt from 8M and up sold at the "Bolt" has a Sugar Crystal Screw Pitch than the one for Motorcycle. Industrial Bolt. If you are planning to get a Bolt from a neighborhood home center, be careful.
[Opinions and requests to Manufacturer
Is there not much demand? Please continue to sell as much as possible.
View detail
The finish is perfect.
I am a bit addicted to Titanium and am gradually replacing Bolt that is starting to corrode on the surface with Titanium.
The low head of the titaniumium cap bolt was very useful because it was hardly available.
I have purchased M6 and M5 cap bolts, and the M6 cap bolt in particular has a 2mm lower head than the regular cap bolt.
A mere 2mm is a mere 2mm, but depending on where it is used, the finished product may vary significantly.
The dimensions are basically the same as OEM, but extra long items are shortened, and for items such as the Master tankBolt that require a reamer section, aluminum tape is wrapped around the reamer to match the diameter.
Titanium is expensive, but considering the fact that it has almost no surface corrosion and is beautiful, I think it's a good choice.
I would like to see a simplification of the package, which includes 1 pc each in a modest package, to reduce the price a little.
View detail
Bolt replacement for MirrorOffsetHolder
Currently, I am using the low type of DAYTOMA's Hi-Viz Mirror and the shorter version of Tanax's Mirror Offset Holder. It is not impossible to fasten the OffsetHolder with other items, but it was not good for my mental health, so I decided to replace it.
However, I have never seen a 1.25 cap bolt, which is often used for motorcycles, at a home center, and I have to order one from a shop specializing in screw bolts by mail order. You have to order from a shop specializing in screw bolts by mail order, or buy from KITACO or Posh. In this case, I only needed to purchase two bolts, and since I did not have any other bolts or nuts that I needed, and since I was not Timing for bulk purchases, I chose KITACO's products instead of ordering from ScrewShop because of the shipping cost. I wanted a black one, if possible, so I hesitated between a black one and a black one from Posh, but I decided to buy a KITACO product because it was a little bit cheaper. The bolt itself is a good product that can be used normally without any problem, but I think the price is too expensive.
By replacing the Bolt with a 5mm longer Bolt, the Bolt is now firmly in place and secure. We recommend replacing the bolt with a new one if you have similar concerns.
View detail
It was cheaper than OEM Parts.
[How is it used?
Purchased as Bolt around Engine of SEROW225W.
Up to 1998 model year of SEROW225WE (4JG6:aka On-bu SEROW), the Bolt used around the Clutch cover and Generator cover is a Plus screw.
I don't care if the head of Bolt is Plus or hexagonal if I just ride it, but I'm afraid of damaging the head part of Screw when I replace the clutch plate, and I like Hexagon Bolt after 5MP for its appearance, so SEROW225 kept in my house is I am afraid of damaging the head part of the Screw plate.
I have been able to use it many times because it is more Reasonable than YamahaOEM's Bolt at such times.
Was the one you received as per Image?
The bolt size is M6 and the head part is 8mm, which is almost the same design as the OEM bolt used for the engine part of SEROW225WE (5MP) and SEROW250, so there is no discomfort at all and the bolt with the same length as the OEM bolt is also available in the lineup, so the bolt size has been changed to Large. It is a product as shown in the image.
Was the installation difficult?
This is only when used as described above.
The bolt on the original PlusHead is carefully removed so as not to damage the bolt, and then replaced with this product, which is the same length as the OEM bolt, and tightened with the Torque. This product is a two birds with one stone solution for me personally, as it will definitely make the bolt less likely to be pinched the next time it is removed, and it also looks better.
How was your experience with it?
I have used Yamaha OEM Bolt in the past, but there seems to be no inferiority to the OMBolt. I have no problem with it, and the price is too low to be thankful.
The number of Bolts in each length is different, but no matter which length Bolt you buy, it is definitely cheaper than OEMB Bolt. (Example:YamahaOEM Product No. 95024-06025Bolt,Flange 1 piece 121 yen×5 pieces = 605 yen, but with DRC, the same size can be purchased for 251 yen for 5 pieces)
[Included Parts:were they on?
None, Bolt only.
[Was there anything that disappointed you?
No problem at all, and since it is a bolt of Steel like YamahaOEM, there is no problem with compatibility with the Case's AluminumMaterial.
Other items that would be helpful
Point and hang of installation
When used, Screw lock agent is applied before tightening.
[Availability and clarity of the Instruction Manual
There is no Instruction Manual because the bolt is exactly as it looks, but in terms of ease of understanding, I think this is a top class easy-to-understand product.
[Notes]
Use properly to avoid twisting off the Head with Overtorque or nipping the Head with improper tightening work.
[ITEMS TO BUY TOGETHER
Nothing in particular, but the product itself is inexpensive, so it is good to buy it together with other products.
[Opinions and requests to Manufacturer
in this vein HondaOEM-like Bolt." Ya SEA BASSOEM-ish." KawasakiOEM-ish." I would appreciate it if each MotorcycleManufacturer-like BoltSeries of etc. is released.
View detail
Titanium
Titanium color is Parenthesis nice and expensive View detail