Reviews
It improves the appearance of theHose.
Not only the appearance but also the deterioration of the fluid can be visually observed, which improves maintainability. View detail
Great Value and Quality Breather Hose Clamp for the Grom
About quality and texture: I am happy with the quality of the hose clamp from NTB, made from a spring steel with a nice silver trivalent chromate treatment surface finish. About the feeling of use: The Honda breather hose clamp is small and weak, the NTB hose clamp secures the hose much better and looks great with it's silver surface finish. Products to buy together: Some more hose clamps in varying in size would also be desirable to purchase along side the BC15.5 hose clamp. Difficulty of installation: The process to install takes just a minute, I find my fingers are usually not strong enough to install these hose clamps so tend to use combination plyers and add some electrical tape to the jaws so to not damage the surface coating. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting a great quality product for a very low price as compared to the hose clamps available from SP Takegawa. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: I find the NTB applicable range a little difficult to workout for the sizing I am wanting but if you look at the photos they attach with the vernier it makes this much easier. View detail
I like that it doesn't rust.
I like that it doesn't rust even after years of use. View detail
Black Panther
It seems a bit expensive, but since this was the only Black available, I guess it had to be done... View detail
It fits with Plating and gives it a luxurious look!
[How is it used?
NORMAL hose guide is rusting and Material:I purchased this one from Aluminum.
Was the one you received as per Image?
The size seemed smaller than the Image.
The texture is not bad and gives a sense of luxury.
Was the installation difficult?
I just need to replace the NORMAL Guide so I can tighten the Bolt and Nut. wdisc needs two of them, so I use one flipped over and inverted.
How was your experience with it?
I have driven several hundred kilometers without any problems.
However, I am concerned about the strength of the Arm section, as it is thin and has been stripped of its meat.
I think it will break eventually.
[Included Parts:were they on?
Body and Clamp Quantity:No other than Set.
[Was there anything that disappointed you?
The hose hole was too narrow to accommodate the mesh hose, so the mesh hose was quite limiting.
Material because there is very little Clearance:Rubber protective cover will not fit.
I use Emon's plastic hose cover for protection.
I don't think Normal hose would be the first place to enter.
I was torn between the ▼Titanium color and the Silver.
Considering the balance with the Titanium color bremboCaliper and the planned Titanium color NITRON suspension, Titanium might have been a good choice.
View detail
BlackBand!
I chose Black to match the Hose because it is visible.
It's not noticeable! Just a bit expensive...
View detail
Holder
About quality and texture Because it's black, the quality looks really high About the feeling of use be still in use Products to buy together External diameter 6 mm oil line Difficulty of installation easy, simple Cost performance and comparison with other products It's easy to compare because of its color About shipping and packaging The packaging is always meticulous The delivery took a week Any concerns, cautions, or advice when purchasing Actually, I bought it wrong after looking at the inside I should've bought it with the outside view View detail
Samco Hose Band
The commercial Hose Band did not feel right, so the Hose Band for Samco on Samco's Hose is good for a clean fitting. View detail
Fits: HONDA Superdio, HONDA Dio (2 Cycles), HONDA livudio
Nice and high quality bolt
Very high build quality. The material also stainless steel and nice looking. Recommended for replacement and upgrade. Beautiful product for your great bolt and disc. View detail
13mm Hose Clamp from SP Takegawa
* About quality and texture, A steel spring clamp with a goldish in colour corrosion resistant coating, not silver in colour like the Webike picture. * About the feeling of use, These hose clamps secure the hose very firmly onto the mating receptical and I do like the clean finish as opposed to the screw type hose clamps that can look untidy once secured. * Products to buy together, Some new breather hose was purchased along side these additional hose clamps, I have moved away from the clear breather hose to the black. * Difficulty of installation, The fitting of these hose clamps is simple when using a suitable set of plyers, I used a set of mini multi grips with tape over the ends to prevent scratching up the coating as much as possible..The process was completed in 2 minutes with no difficultly. * Cost performance and comparison with other products, At just over $1 AUD each I find the pricing reasonable but the ones available from NTB can be had for half this price and I will gives those a try if I need more in the future. * About shipping and packaging, I am happy to wait 6 weeks on average for my parts to arrive in Sydney Australia via Webike's sea freight which comes with tracking and insurance so I know I'm covered in case something was to go wrong but with there outstanding bubble wrapping and boxing there have been no problems. * Any concerns, cautions, or advice when purchasing, I can see that maybe using these goldish coloured hose clamps may not be very aesthetically pleasing when paired with the new black breather hose so if that is the case for yourself, Daytona offer these hose clamps in black. Use the product reviews to assist in making a decision on your purchase. View detail
People who want to be particular about where they can be seen.
I bought a pack of 5.
After Black paint in product description [Color] It says something like Clear Coating, but don't expect too much because you will be sad if you expect too much!
I have not compared them, but I think they are more Black shiny than otherManufacturer
I am very happy with my purchase.
View detail
The Torque is strong and easy to use for the price!
This product is easy to use and has a strong tightening Torque for the price, and it is AllGold, so it is heat resistant, which is a good point! View detail
Relief
The quality is good and safe to use.
It is also rust-resistant and can be used for a long time.
View detail
Is good
The width of the Grip is wide, so it grabs firmly and Clips the Hose.
It is easy to use because it can be removed quickly by grabbing the knob with pliers.
There is no leakage of Fuel line hose and it is safe to use.
View detail
good
The quality is good.
It grips well and there are no leaks.
The tightness was not too tight, but just right.
View detail
Fuel Hose Clip
Clip was replaced along with the replacement of the fuel hose on NSR50.
It works fine
View detail
Quick and easy to get the right Size
They are conveniently available in numbers without being cheap in quality. I would like to see them in packs of four each, even if the price goes up. View detail
always
It is convenient to buy a variety of Sizes in bulk because there is no Drill if you buy these items every time you need them. View detail
Maru available in 1pc. units.
I bought this one to replace the hose clip with a firmly stop plate Spring type. I had no hesitation in deciding on this one because the narrower the diameter, the more limited the choices.
The NTB clamp is easier to pick up because the ear part is a little longer than the spring type clamps that are also found in Manufacture OEMs. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units.
View detail
Maru available in 1pc. units.
I bought this one to replace the hose clip with a firmly stop plate Spring type. I had no hesitation in deciding on this one because the narrower the diameter, the more limited the choices.
The NTB clamp is easier to pick up because the ear part is a little longer than the spring type clamps that are also found in Manufacture OEMs. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units.
View detail