Reviews
I lost it, so...
The push rivet that stops the side cowl of YZF-R1 was lost, so I bought it.
SizeExactly.
I looked at the Touring and a little bit of the Circuit and had no problems at all.
View detail
Quantity:It would have been better if it was 1 Set of 4pcs,
I purchased the 4mmSize Rivet because I needed it when installing the MC21 Screen.
What I wanted was 4 pieces, but the Quantity:I bought two because it was 1 Set of 3pcs.
There are two different lengths of 4mm Nylon rivets from KITACOConvenienceParts, and I was not sure which one was better. There are two types of rivets with different lengths, and I was not sure which one was better, If it's a scuzzy one, why not just put a Washer on it?" I bought this one because I thought it was perfect.
OEM Parts are still available, so if you are concerned, OEM Parts are the way to go.
I am satisfied with the price, which was less than the cost of four OEM parts.
View detail
desorption
I bought this to fix Screen to prevent scratches and for easy removal.
The price was reasonable, but the diameter and length were not quite right. The diameter and length did not fit well.
View detail
For fixing plastic parts and
I thought, "Can't I use it to fix the Screen? The price was reasonable, so I bought it.
It was impossible due to the thickness of the fixed section and lack of length.
It can be used in other fixtures and will be used there.
View detail
Size did not match ADV150
It was meant for Honda, but it was not available because it did not match the size of the push rivet used on the ADV150.
I think it is a normal product for a push rivet.
View detail
Used for 250SL (Repair)
I bought a new Ninja 250SL… because I lost my push rivet at some point.
I purchased and used it. The quality is high and I can use it without any problem, but I still feel that it is rather expensive…
View detail
diversion
I bought it for my SCUB, so this time it is a push rivet, but I used it for my PCX because the push rivet was damaged when I changed the battery of my PCX. I wish it was a little more cost-effective. View detail
Unless you're in a hurry.
If you need it in a hurry, it is possible.
If you are not in a hurry, you should order OEMParts.
The prices are too different.
If you have time, I recommend you to buy OEM Product.
View detail
Good
The quality is the same as NORMAL parts.
Removal and installation can be done with a single push for convenience.
View detail
It can be easily fixed and released by simply pushing it in.
This product can be easily fixed and released by simply pushing it in. Good thing it comes in multiples, as they're prone to breakage! View detail
Same shape as OEM Product
This is the same as the TomClip used in the SPACY100. (Size/Shape)
Material:Because it is Plastic, it will be missing at the nail in a few years.
But how can something like this cost more than 100 yen (one piece)?
I think it's expensive, but I can't find a cheaper alternative, so I have no choice but to buy it.
View detail
Unchanging quality
This is the same quality as the NORMAL parts and is useful to keep in stock in case of damage or loss. The grip is easy to remove and install with a single push, and can be removed without tools as long as there is no sand or other debris caught in the grip. View detail
To Cowl.
I used it to fix Cowl.
It can be used if the hole diameter and depth match.
View detail
It's handy to have as a spare.
Push rivets are often used in Yamaha and SEA BASS, but they always deteriorate over time.
Parts are often broken when removing and removing them, or they become too habitual and difficult to reuse.
It's not expensive and I try to use a new one when it goes bad, but KITACO releases them by Manufacturer, which is very helpful.
View detail
They were the wrong size!
Trial and error for Grom's Custom It's not easy to get used to, but I'm enjoying learning a lot of things I'm not used to it, but I'm enjoying learning a lot of things I do this with admiration
However, due to the inexperience of the work, we often lose sight of the small parts and break them When removing the exterior of the grommets, some of the material:You have to remove the plastic grommet (like a Rivet) At first I didn't know how to remove it, and when you push the center part with a thin stick, the whole thing comes out But at this time, I had too much momentum, and the plastic part in the center of the plastic part flew somewhere
So I've been looking for the same part for a long time, but I couldn't find it, and finally I found it! I was surprised that KITACO prepared such a small item for me What a conscientious company! However, the parts I received are the same shape and function, but the size is different (for groms) It was much thicker than the original We-Big's web site alone has a lot of different shapes and sizes, and I'm not sure which ones fit I don't know if this is the best for HONDA I'd really appreciate it if there was a Guide like that, but for such a small part It's not easy to prepare Large strange to prepare
View detail
I think whether it is an OEM Same Product
The plastic part has been removed many times
I will crack now..
It is safe to have several as Spare
Those of Size are not sold at Home center
View detail
Purchase again for Stock
With this area Rivet, play is easy to come out when the three-prong is opened when you remove it like a photo.
Cowl's backlash was checked and all the open places were exchanged and became chitin, stocks were gone, so we ordered additional order.
View detail
I tried to exchange regularly.
Purchase Size of SEA BASS car type as we remove Cowl.
The place where the Rivet's three-prongs had opened had a backlash in the combination of Cowl, but when it is brand-new it will become exactly fit and it feels good.
It is not good maintainability to assemble Rivet which is still open ... I can not taste the final "maintenance completion feeling", so I added it to the List of Parts to prepare before removing Cowl.
View detail
Push rivet
【WebikeMonitor】
I replaced it because it cracks with aged deterioration.
It is recommended because it is cheaper than OEMParts.
We are collecting orders and putting in inventory of Parts
View detail
Purchase for replacement
Originally attached Rivet was broken leg while removing or attaching Cowl for servicing. I bought it for replacement, but Sizeetc. It was same and compatible. Durability is now confirmed. View detail