Reviews
As you tighten it in.
I use it for Caliper's rubout etc. When I tighten the Screw and open the Plate with 4POTCaliper like NC30, the Plate is not parallel and I can't get the 4 Pistons to be even etc.
The fact that it cannot be pushed in makes it difficult to use. The texture is good, so I would like to have the Guide of Plate as Quantity instead of 1 pc.:I am wondering if I should have purchased the 2pc one.
View detail
OHLINS Preload AdjusterTool
As for the dryness of use, it is only an OEMTool, and the accuracy of the Size is good and easy to use.
But the Gold amount is still too high.
View detail
The stuff is good, but I didn't need it!
Purchased to remove Locker Arm on xs250sp 4a8.
I bought it without checking because it was mentioned in the tool section of the service manual and was also used in the photo of the procedure for removing the Locker Arm.
As a result, the Bolt of Locker Arm was M8 and the size was not M6.
If you check the photos of the procedure carefully, it is just a Bolt. The color is different!
I bought a M8×180mm Bolt for 300 yen at a nearby Home center and was able to remove it successfully.
Things are good. I just didn't need it.
View detail
Note the length of Drill.
If the Drill length is too short, the hole cannot be drilled. View detail
I don't think it fits...
I couldn't figure out why it was exclusive to 2Valve, so I bought it to try it out.
As a result, the duplex Spring could not be pushed off by hand and could not be used.
For use with Mini bikes.
View detail
You can't have hard ends.
I could not Cut the hard end of the PillowGrip on the Pro taper.
I stopped because the iron part of Cutter was deformed while I was beating it.
I bought it for this...
Since the Material is iron, I thought I could make the cutter part a little sharper.
The kratom crackers in the picture cut it with no problem.
I don't know if it's because I don't care too much about the finish, but as others have said, the holes are definitely a little gapped.
If you don't mind, it might not be a problem.
It's not a tool I use often, and the price seemed a bit high, so I didn't change it for a long time.
If it was about $1,500, I would have bought it sooner.
I thought it would be nice to have a plastic Case to store everything in!
View detail
Difficult to use
The accuracy of the metal saw's guide is not quite right, and it gets stuck in the middle of the process, which can be a bit annoying. It is. View detail
I was sent a shoddy product
I ordered a specified part number that fit the top cap, but received a poorly processed item that did not fit the size at all
The top cap was scratched at the tentative fitting stage, and was replaced by the official Japan distributor We have submitted an Objection directly to EngineerRing
The top cap was scratched by a badly machined tool, so we asked them to process the tool to make the top cap more durable The cap was also replaced with a new one
Mr. MatsumotoEngineerRing's objection support was very reliable, but the I think it's best to inspect the product itself by yourself because it may be a bit of a stretch It is
Since it is a Made in Italy product, you should be more careful than Japanese products When something happens, it takes a long time to deliver
We recommend that you contact your authorized distributor immediately if there are any deficiencies
View detail
Pump and Hose need more time!
The essential Pump and Oil Resistant Hose are removed during work. Since it does not become a thing if it is as it is, I fixed the joint with liquid packing. Pump is made by medical NIPRO, but it is not compatible with Oil Resistant Hose.
Well ~ Motorcycle related Parts are generally useless unless you add your own hands!
View detail
This set alone is not enough
I thought.
Even if applying a negative pressure with a bending angle Pump since it does not fit in the attached Breeder installation Parts
I will take in air from the gap between Breeder and Joint.
Since it can not be helped, purchase a small Silicon tube one size at home center
I used it for Joint between the attached Hose and Breeder.
View detail
Lack of explanation of goods
I bought it for things like for On Road, but the depth of Bolt hooked in the hole of Spacer was short, so I could only hook Bolt to One Side for my Motorcycle Spacer. When I contact Manufacturer "Please understand that it is a universal product" I did it with. Universal Product that can not be used widely At least the usable range (Size) I think that should be explained. By the way my Motorcycle is famous ManufacturerY
View detail
Fits: YAMAHA TZR50, HONDA BENLY50CD90, HONDA XL80, HONDA XR100, HONDA XL50, HONDA NSR50, HONDA NSR80, HONDA NS50F, HONDA NS-1, HONDA CRM80, HONDA MBX50, HONDA CRM50, HONDA CR80R/RII, YAMAHA TZM50R
[Webike Monitor] Although there was that the Manufacturer of the VOX of the Lock nut is also different, the VOX side of a Lock nut was large, did not pass along the hole of middle, and did not use after all. It seems to be better to actuall
[Webike Monitor] Although there was that the Manufacturer of the VOX of the
Lock nut is also different, the VOX side of a Lock nut was large, did not pass along the hole of middle, and did not use after all.
It seems to be better to actually see and buy a thing.
Or [ that
or the Brand is good ]
View detail
An attached Hose is short and inconvenient. The Hose separates from an injector immediately and it is inconvenience. If it buys shortly [ ], it will be made what a Hose does not separate from easily.
An attached Hose is short and inconvenient.
The
Hose separates from an injector immediately and it is inconvenience.
If it buys shortly [
], it will be made what a Hose does not separate from easily.
View detail
It will be OK if it uses for extracting a Brake fluid. Air omission --
It will be OK if it uses for extracting a Brake fluid. Air omission -- View detail
It was small than expected.
It was small than expected. View detail