Reviews
Used to remove O2 Sensor from CT125CT110 HUNTER CUB
Used this one that fits Size for cleaning Sensor.
The ZETA Under Frame Kit is installed, but as it is, it interferes, so it needs to be shifted a little. (Just remove the footpeg side and you're good to go.)
Like the 110CUB, if there is a Connector on the Sensor head, a Deep socket or similar can be substituted, but without one on the CT125, there is no way to remove it, so I think it would be good to have.
View detail
Seal mounting is easier.
I am concerned about the durability of plastic, so I prefer DRC's Stainless Steel tool, but it has been out of stock for a long time. I would prefer to use DRC's Stainless Steel gloves, but they have been out of stock for a long time. It is inexpensive, so I can just give up and buy a new one if it breaks. View detail
As expected, OEM Product
I purchased this to remove the Rotor on my GB250Engine. Since it is an OEM product, I was able to remove the Rotor without any problems.
It would be great if we could get it for a little less.
View detail
Shoo, Pushing, Shoo, Snap
Used for new Valve replacement work on CUB.
I had to replace my previous tacho bar because the Rubber had been ruined.
The feel of the product is the same as the previous one.
The tacho did not come off and could be worked normally.
It's not a task I do very often, but I appreciate being able to purchase it because I can't move forward without it.
It also comes with Compound, which is helpful.
I hope that the Red Lead used for marking will also be available in the size of the Compound included with this product.
View detail
It is a useful Tool.
I purchased this product to measure the sag of XEF250.
Rear tire floated "0G" from the state of the straddle. "1G." state, measure the difference and adjust the Pre-road of the Suspension so that the SuspensionStroke is one-third when straddled.
Marker shows the difference in Stroke, so work that used to be done by two people can now be done by one.
One point to note is that at first the screws that hold the Marker to the Wire were tightened, so the measurement could not be taken properly.
It needs to be loosened a little so that it moves Smoothly.
One third of SuspensionStroke was 62mm, but I set it at 73mm to soften it.
I will be driving in various areas to further adjust the Pre-road.
View detail
Good enough for the price.
I chose this product because of the price, but I am fully satisfied.
The consolidated Spring of Exhaust System is sufficient for this purpose.
View detail
As a primer to make car washing easier.
I used to put my off-road motorcycle on the transporter after a race and ride it home without cleaning the dirt off the body. However, by the time I arrived home, the dirt had hardened into a stubborn stain, making it difficult to wash the bike each time... (And mud falls in the Transporter...) If that's the case, why don't you just clean up the dirt there? So why don't we just clean the dirt off the car locally? I bought this to clean the dirt that gets into the back of the Fender, the footpeg, and the tight spots on the body at the site! I will use it in the future when I have a chance. View detail
Fits: HONDA glom, HONDA glom, HONDA MONKEY125, HONDA DAX 125
A little expensive.
Purchased to replace the springs on my Groms.
It is not impossible if the inner tube is held in a vise.
In the meantime, we have a special tool for this purpose.
The product is solid as a rock and nothing is wrong with it.
But only for tools that I don't use a lot.
I'd like to spend a little more money.
View detail
works well and easy to use
Quick to adjust, excellent hold on the clutch to tighten nut. I would definitely recommend this product (tool) for anyone working on bike engines and proper maintenance on their bikes. Used on both my clutch, and my flywheel. This tool worked well and saved me alot of time when disassembly and rebuilding my motor. Built with quality and easy to use. This tool is a must for engine rebuilding View detail
Fits: SUZUKI RM250, SUZUKI RM125, SUZUKI RM-Z450, SUZUKI RM-Z250, SUZUKI DR-Z400SM, KAWASAKI KX450F, KAWASAKI KX450, KAWASAKI KX250F, KAWASAKI KX250 (2019-), HONDA CRF450X, HONDA CRF450RX, HONDA CRF450R, HONDA CRF450R, HONDA CRF450L, HONDA CRF250X, HONDA CRF250RX, HONDA CRF250R, SUZUKI RM-Z450
DRC Pro fork cap wrench
This fork cap wrench is good, light, compact & strong. It comes with english instruction. So now i can work with ease & piece of mind to replace newly bought outer tube and aftermarket spring. View detail
ใช้งานสะดวกรวดเร็ว สินค้าดีมีคุณภาพ View detail
It is not a tool that is used so much in Private, but …
I had a Pin type Holder, but I bought it just in case.
It was more solid than I expected and the desired work went off without a hitch!
View detail
YOSHIMURA Timing wheel
It is not used as it should be, but as a display version of a clock. I am satisfied with the appearance. View detail
Enough for Sunday mechanic
[How is it used?
STAND and Exhaust System during vehicle maintenance (Chamber) It is used to remove and install Spring for replacement etc.
Before purchasing this product, I had been working hard with a radipen, but I purchased this product to increase work efficiency.
Was the one you received as per Image?
It was just like the picture.
How was your experience with it?
The hook is processed so that the tip of the hook is tapered, allowing for smooth attachment and removal of the spring.
Also, the T-section is well reinforced, and although it is inexpensive, it does not seem to break easily.
The size is neither too small nor too large, but just right.
[Points to note]
None in particular. Surprisingly comes into play when it comes to maintenance.
How did it compare to other products?
This product has no problem, but some of the ones I used in the past had no reinforcement at the T-junction and would break off.
This is a part where force is inevitably applied, so I think this product is good because that part is reinforced.
【Review】
It is fairly inexpensive, but I think it works well for starters.
As expected, the durability will be inferior to those of famous manufacturers when used over a long period of time, but I think it will be sufficient for Sunday mechanicLevel.
View detail
Fits: HONDA MONKEY, HONDA DAX70, YAMAHA Yamaha50ccScooter, YAMAHA GRAND AXIS, YAMAHA JOG90, YAMAHA AXIS 90, HONDA LEAD 90, HONDA MONKEY, HONDA Honda50ccScooter
Solidly built
Purchased for disassembly of Clutch.
It is well made, and although I purchased it for the Clutch maintenance of the Address100, it is still a generous Size and can be used for the MAJESTY250.
The shape is designed for use with Wrench, and it can be easily disassembled and reassembled.
View detail
Convenient to have
Purchased to change the Fork oil in my Gixxer 250.
If I wanted to do it cheaply, I could have substituted various tools, but I bought this to make sure it was adjusted properly because it is an important part.
Will be replaced at the end of the year!
View detail
Fits: YAMAHA SEROW225, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA XT250X
It can be used on RZ250R Rear!
AssistTool by Kitamura can be used for RZ250R's RearShaft because it is 15mm.
You have to maintain the Tire height a bit to pull it off cleanly.
Please give it a try.
View detail
KITACO Gear Holder
About quality and texture The packaging is excellent and has a reliable quality About the feeling of use It hasn't been used yet Purchase to use when changing ENG crankshaft Products to buy together kitaco Engine Special Tools Difficulty of installation This product makes the work easier Cost performance and comparison with other products I'm not sure about other products, but as it appears in many ape100 engine overhaul videos, it's essential when assembling an engine About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing It was a little difficult to tighten the bolt last year because the engine was disassembled and there was no tool I'm thinking of replacing the crankshaft this winter, so I'm buying this product View detail
Convenient to have
[How is it used?
YAMAHA XJR400R (07) Exhaust System replacement, etc.
The Exhaust System is removed when the Exhaust System is replaced at the time of vehicle inspection or when the Oil Filter is replaced.
In doing so, I have been using Pliers and others to pull Spring, but it is quite difficult to do.
I knew there was an exclusive product, but I had not been able to purchase it.
Was the one you received as per Image?
The image was exactly as shown in the image.
I was reluctant to use it because it has only one application, but since it is compact, it is easy to place.
How was your experience with it?
It is quite easy to use.
Installation and removal of Spring is now much easier.
I wish I had bought it sooner. w
[Points to note]
Nothing special, but be careful not to work on Spring so that it doesn't blow up!
How did it compare to other products?
I don't know because I have not used other products, but considering the price, I feel this product is fine.
It has the best cost performance.
View detail
Fits: HONDA glom, HONDA Super Cub 50, HONDA SUPER CUB110, HONDA SUPER CUBC125, HONDA MONKEY125
Must have Assembly Tool for the Crankshaft on the Grom
About quality and texture: I am happy with the quality of the crankshaft assembly tool from Kitaco, made from steel with a durable coating and comprises of three parts to the tool. About the feeling of use: Used successfully to install the crankshaft into the right side crankcase and I don't see an easier way for this to accomplished at home. Products to buy together: Many of the Kitaco tools like the flywheel puller and the center lock nut wrench would also be desirable to purchase along side the crankshaft assembly tool. Difficulty of installation: The process to install takes just a few minutes, install the spacer over the shaft, thread the adapter onto the shaft and then the nut onto the adapter and you are ready to start pulling the crankshaft through. Not difficult to do. Cost performance and comparison with other products: Good costing as you are receiving a quality tool that will save you the cost of a visit to the local workshop with no other brands offering this tool for the Grom specifically. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: All of Kitaco's tooling is of a very high quality and I can't recommend them enough. View detail