Reviews
Low price but sufficient Quality
The price of Motion pro was too high, so I went with this one. The price is a quarter of the price, but the quality is solid and this product should be sufficient. The box is just a bonus, and the lid closure is so roughly made that it won't close after a few uses. View detail
Spring Detachable
I purchased this product to use for removing and installing springs when removing and maintaining the Exhaust System.
The length is just right, no slippage or pain at the grips, and they are easy to use.
I don't use it that often, but it would be useful to have 1 pc.
View detail
Used for CYGNUS6 type
Used to replace RaceBearing on CYGNUS Type 6
It seems to be strong and will last for a long time.
View detail
Fits: HONDA CB900F, HONDA CBX1000, HONDA CB750F, HONDA CB1000C 83, HONDA CB1100F, HONDA CB900F, HONDA CB750F
Can be used for CB750F
I bought this to replace the ValveShim on my CB750F. The Honda-specific tool is already discontinued, so some people make their own. At first, I tried this Hondafor Vehicle. The actual tool is surprisingly small, but it's not to be underestimated:just insert the tip of the tool between the cam and push it in, and the valve lifter will drop and the shim will be easily removed. The cost is great, and it is truly a god tool. View detail
MINIMOTO Minimoto Tappet Adjustment Tool 3-Size Set
Fine-tuning of Valve clearance is more convenient than using ordinary tools
The accuracy of the tools is low and I would like to see the system a little more precise.
View detail
It is not a tool that is used so much in Private, but …
I had a Pin type Holder, but I bought it just in case.
It was more solid than I expected and the desired work went off without a hitch!
View detail
Fits: HONDA MONKEY, HONDA DAX70, YAMAHA Yamaha50ccScooter, YAMAHA GRAND AXIS, YAMAHA JOG90, YAMAHA AXIS 90, HONDA LEAD 90, HONDA MONKEY, HONDA Honda50ccScooter
Solidly built
Purchased for disassembly of Clutch.
It is well made, and although I purchased it for the Clutch maintenance of the Address100, it is still a generous Size and can be used for the MAJESTY250.
The shape is designed for use with Wrench, and it can be easily disassembled and reassembled.
View detail
Reasonable
OEM clutch holders are expensive, so we used this one instead.
This is sufficient for use.
View detail
cheap
OEMClutch holders are expensive, so we purchased this one.
Unlike OEM, it is not fitted into a hole, so although it is unstable, it can be substituted adequately.
View detail
Strength
Simple construction makes it hard to break. It is strong and sturdy for its appearance.
Even hard springs can be pulled firmly and safely.
View detail
To disassemble the Clutch
[How is it used?
TZr250R (3XV) I bought this to Rose the Clutch of
Universal's Clutch holder is available from several manufacturers, but I chose this product which was relatively inexpensive.
Was the one you received as per Image?
It's no surprise since it keeps the Clutch down, but it was much bigger than I imagined.
There was no deformation, and the production seemed to be good.
How was your experience with it?
I used it for the first time so I had to watch and learn, but it was surprisingly easy to fix.
I was worried because there was an imprecation that it could not be fixed, but I did not have any problem.
However, I was a little worried because the hook was shallow, probably because of Universal.
[Points to note]
It is important to note that depending on the motorcycle, there is a possibility that the hook may be shallow or not hooked.
【Review】
The tool is only used to hold down the Clutch, but it made the job easier.
It's not that expensive, so it's handy to have one if you're rooting an engine.
View detail
Can't hold the nail open.
[How is it used?
I used this to replace the Clutch boss on my MT-07.
Was the one you received as per Image?
This is a general Clutch holder. There are several companies that sell the same shape.
How was your experience with it?
The pawl tip format is bad, and when Torque is applied, the Y-shape spreads and the pawl comes off. There is a screw type stopper to control the spread, but it is defeated by Torque.
The reason it spreads is that the tip of the nail is cut at an angle to fit easily into the groove of the Clutch boss.
I had to tighten the Stopper with a water pump ply shop to get it to work. I don't think that's the way it should be used.
[Points to note]
The Clutch boss has a high fastening torque, so if it comes off you could get hurt.
View detail
Was good
This is the first time I've done a Wiring hollow through. I was surprised at how easy it was to open. I think it is good to have it. View detail
Fits: HONDA MONKEY, HONDA APE 50, HONDA glom
unsuitable
The Size of the teeth do not match the GEAR of the Clutch on the Grom.
It's not useless, but it's the same as chewing on the right stuff.
View detail
The strength of the product is reliable.
The price may be a little cheaper, but for the appearance, it is strong and durable. You can pull the hard spring and prevent the exhaust system from being scratched and you can use it safely. View detail
Was good
I'm glad I got it at a reasonable price, I used it for the Wiring middle passage and I think it's so easy to drill even if you can't come. It is very easy to make a hole. View detail
Fits: HONDA CRF50F, HONDA XR50R (for competition), HONDA GIORCUB, HONDA DAX, HONDA CHALY 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA solo
It is convenient to have
Used for Clutch overhaul.
You need to loosen the Bolt in the center of the Clutch lowers, but you need to hold the Rotor because it turns. So you need this tool.
good point
You can hold the Rotor firmly. So it's easy to loosen the bolt. It is also easy to insert the bolt when reassembling.
You can use Honda's Horizontal TypeEngine Clutch.
The accuracy of the tool is also good.
A bad point
I'm not sure if I need it or not, since it's specialized for use Case.
It is possible to press the Clutch lowers by hand, but it will take a lot of strength and you will get tired, so it is better to use a tool.
View detail
Used only once
I used it only once to drill a hole in my HURRICANEHandlebar, and had no problems. View detail
Fits: HONDA CB900F, HONDA CBX1000, HONDA CB750F, HONDA CB1000C 83, HONDA CB1100F, HONDA CB900F, HONDA CB750F
Messiah Tools
I used it for CB750F.
As with the OEM tool, the method of use is from the Plug side. Note that it cannot be lifted from the outside.
Some people make their own tools because the OEM tools are out of print, but considering the production time & Cost, this tool is cosmetically superior! Thank you very much!
View detail
Fits: HONDA MONKEY, HONDA DAX70, YAMAHA Yamaha50ccScooter, YAMAHA GRAND AXIS, YAMAHA JOG90, YAMAHA AXIS 90, HONDA LEAD 90, HONDA MONKEY, HONDA Honda50ccScooter
Can be used without problems
There is no Instruction Manual, but I was able to use it without any problems.
I think it's a good tool to buy because it has several uses.
View detail