Reviews
It can be used normally
There is not much in the way of luxury or design in terms of appearance.
It has been stored in an indoor toolbox and has not rusted for 8 years.
The Grip is thin and painful for a tool that requires a lot of force to use. However, you can turn the Piston with the grip strength of an average man, if it doesn't stick, you can do your best.
Also, I've never felt the need for the Butterfly Screw when using it.
The butterfly screw is used to make it close in Small size when storing. The width is about 43mm up and down without the butterfly screw.
Material is a material that sticks to magnets, so we use separately purchased magnetic holders for storage.
View detail
Two (or three) axes are better
I've been using products with a single-core shaft guide
The structure is severely twisted, limiting its use
I think this product is good for GJ in that regard
View detail
Pretty good
I used it to clean the Piston on the Brake Caliper
Without this product, cleaning the Piston would be quite a challenge
Thanks to this product I was able to wash the Piston and the Touch of Brake is very good! became
View detail
Made by DAYTONA, the trustworthy company
I bought it to clean the Piston when I replaced the Brake Pads By turning the Piston, I was able to clean every nook and cranny View detail
The problem before the product
I made a phone call, but the man who answered the phone was unpleasantly surprised by the unfriendly manner in which he spoke to me The employee training was inadequate and the quality of the products made by such a company is to be expected I expected it to be a local company, but I would never bring it up for purchase again View detail
An indispensable tool for BrakeMaintenance
This is a must-have for Caliper overhaul The price is attractive
The whole thing flexes when you apply force to remove the Piston that just stuck to the strength
Also, since the maximum opening size is 37mm, it depends on the type of car, but it's a 2-pot type I can't pinch the Caliper pistons on the..
View detail
I think the grip could be a little thicker
I bought it to try Caliper cleaning and used it immediately after receiving the product
There are many similar products, and if you look at the reviews, you'll often see that the inside of the Piston is damaged It's often reviewed, but so is this one
I used Vinyl Tape wrapped around it as appropriate
It is not so hard to turn the Piston, but it is still a little hard, so the Grip can be thin It was there and it was easy to get tired
It's a cheap part of the market if you think about it including points, so it's just right for those who are interested in it
View detail
It's good enough
I bought this for Caliper OH and rubbing out
Does the Piston of a vehicle left outdoors for 3 years grab no problem? I was able to
This product is very easy to hold in your grip
View detail
Good cost performance
I bought this one to clean the Caliper myself for the first time!
It's not difficult to use for normal use, and I'm happy with the costumes
View detail
useless for the price
I was worried because it was cheap, but I received something that was rather solid
To clean the Brake Caliper, you have to push the Piston back in, but not by hand Impossible
I can do this one
But it's hard to screw in It's hard!
Well, but it's like this
View detail
It's handy for pad replacement
When changing the brake pads, you can use the pliers on the four-wheeled Large Caliper with some creativity The piston was pushed in, but it is difficult to work on the small for motorcycles I bought it because
When the item arrives and you open the box, is it used? I think it's a bit of a scratch Well, I don't mind it because it is a tool
Because Lever is heavy and hard to turn as it is, after applying Grease to the moving parts, the work is done I worked on it and I managed to do the work
I think it's useful for those who often use cars and motorcycles in relation to Brake
View detail
Mostly successful
A must for maintenance of your Brake Caliper
I used to use Snap Ring Pliers as a substitute, but the efficiency is still very different with it is
This is one of the cheapest PistonPliers on the market, but it's perfectly safe to use
I wish these tools could be used for different tasks;
View detail
High cost performance
Used for Brake repairs in Private Piston which was stuck and did not come off was turned and come off with these Pliers When the maintenance of Brake is done in the future, I think that I will use it positively I think that the person who does the maintenance by himself is indispensable Items View detail
Performance as expected
Although there was also a little cheaper, I thought that it would be cheap and bad ... I made it made by DAYTONA. Cripion is attached to Grip, I think that it is easy to grasp. I cleaned up the Piston Pin of each of the three Motorcycle and used it, but I could use it functionally in any Caliper (If it matches only the diameter) View detail
Strong, long-lasting making
Simple, making is steady. It is heavy because it is sturdy, but I think that it is a product that you can use for a long time. I think that it can be used not only for two wheels but also for four wheels. View detail
It is a price. First of all,.
It's expensive, but it's totally better than nothing. It was good.. No problem at all if it is the first tool. You can relax easily. View detail
You can use it enough
I used it for Piston which is a little fixed, but it worked well. Certainly, if you use it for strength, scratches inside Piston, but there is nothing to do with the performance of Brake, and it seems like I can not help it. Rather, at this price, I was able to maintain properly even with Piston, so it was good. However, because it is a bit delicate as a build, it may not be suitable for Piston where the size is sticking too much or Size is Large. View detail
You can use it.
After previewing similar products at the Motorcycle supplies store, I also decided to look at other people's impres. Point decided for this product, because it felt that it was harder to hurt the hand than Cushion of the grip part, or thickness, and other Pliers. I can hold it firmly and turn it.. I do not use it everyday, and assuming the frequency of use, I think that it is a tool that can be used for a long time. View detail
It is tough and long-lasting
I tried it immediately, but it is a simple making, and it is a sturdy feeling. Of course Piston pushed back firmly. I assumed it from the beginning, but when you remove Caliper, it is a good idea to prepare a little table so that Caliper will not be dangling with Brake hose and put it there. (When you do not remove Brake hose) I think that it is not a frequently used tool, but I think that if you have one, I think that it can be used for a long time, so I decided to use Cospa as Point. View detail
Absolutely necessary, but unsatisfactory
It is used to grab Piston in Caliper.
To grasp Piston pretty well, I grasped it pretty handly,
It is necessary to tighten up Stopper.
The Stopper is stopped at E type retaining ring,
Absolutely blow away. I can fix it, it is iteration.
Also, Stopper 's Bracket is also weak and it will bend.
You can fix this, though - - -.
The overall rigidity is weak for a while.
So this price is too high. I thought that it was a defective item rather than Level.
I want you to make a more solid one.
View detail