Reviews
I chose it for the cospa.
I bought this in a hurry because the Piston Pin was very dirty.
I chose it for its price, but after using it, I am satisfied with its workability and functionality.
View detail
Sadly these did not work for me
About quality and texture - The whole tool is made of quite thin materials and feels undersized. For example, the handle has square edges and even with the covering it hurts to hold this tight in your hand and turn it. I found that I needed to hold it tight before turning as the lock screw is very thin (M3 size?) and if felt that if I tightened it too tight i would just cross thread it or round it off, although the folded steel bracket that holds this screw bends when you tighten as well so maybe its poor design (only held on one side) would stop that? About the feeling of use - It hurts to use this tool on an old caliper that needs a lot of pressure. I expect this would be ok on something that was in good condition, but on an old rusty caliper (with clean piston faces) this tool did not work. The (looks hardened as you can see in the photo) grips in the 'jaws' dug deep into the old piston inside edges and ripped the steel. Not something you would wish for if you wanted to keep those pistons. About Design - I think the deisgn is good but this set is cheaply made and I expect not the best example of the design. It is certainly not strong enough for being used on an old caliper where is piston is tight as that needs force to move it free, but I think that is probably the only reason DIY people like me would buy this tool. So, I have to say the design is 'bad' in this case. Cost performance and comparison with other products - It is cheap, but for my use it was money wasted. I didnt break it so I can at least use it on other (better) calipers, but it didnt do the job I wanted even when I heated the caliper. So I spent money on a tool and am no further forwards. There are other tools that look similar and I would look at those instead of this one. About shipping and packaging - shipping was fast and it was well packed. Any concerns, cautions, or advice when purchasing - I would not purchase this tool again and I suggest any potential buyer looks for another version that is built much more strongly if they are trying to work on old calipers. View detail
MinimotoBrake Piston Pliers
Purchased because I am replacing the pad with Self. It is inexpensive and easy to use. View detail
CaliperOverhaul
I purchased this for CaliperOverhaul.
It will be a dedicated tool for that purpose, so there is no other use for it. If you are going to borrow it from another source, it would be better to do so.
Now, I don't have such a reliable friend, and the choice was to pay a Motorcycle shop to do it for a high labor charge or to do it myself, and then TotalCost becomes an issue.
How much would it cost to get the tools myself? If it costs nearly 100,000 yen just to get the tools, I would not hesitate to ask a Motorcycle shop to help me. I think I can do it. Thanks to finding this product, which is very cost-effective, I have decided to do it by myself.
By doing it yourself, you can take your time to clean and check. This time is fun. Of course, self-responsibility is the primary requirement. Prepare well and find someone to talk to if you think it is not going to work.
You had not yet given me any feedback on how you used it.
It is inexpensive, so it may be adequate, but the grip is so thin that removing a lot of pistons hurts my hands. Wrapping a tubular sponge or rubber around it will improve the pain. Also, if the piston diameter is small, the grip width is large, so it is hard to handle.
But it was cheap, so I am satisfied.
View detail
It is easy to use
This was the first time I rode Brake's Piston, and I was pleased with how easy it was to use. However, since I have an air compressor, I don't think I needed it. View detail
Lock Function is very useful!
The night of 15 when I thought that all Piston Extractors were the same.
Piston polish that was convenient to use the lock mechanism this time
BlueMagic is seriously awesome!
Well, what I'm trying to say is, congratulations on your marriage, Gacky!
View detail
If it's not stuck, it's not stuck;
It is not possible to hold the piston with grip strength alone when removing a stuck piston.
Even if you wrap Towel around it, your hands will hurt.
You might like Stopper included. which is a little above Class.
I turned the Pliers upright and stepped on them with my foot to remove the grit.
For turning Pistons when cleaning.
View detail
Wound goes into Piston.
Used for Caliper piston rub.
It is impossible to pull out the piston without this, unless the piston is in a good mood right after assembly.
There was no hesitation in using it, and it was strong enough to be used for a 250cc single push Single.
The drawback is that the lock to keep the tool open is applied by itself when you notice it, and Stress may boil. It's not a fatal problem, but the Lock Function is not really needed.
In addition, because the edge of the tool bites into the inside of the piston structurally, the piston will be scratched to a small extent. This is unavoidable, but if you are a nervous worker, you must take measures such as biting the Dustcloth.
View detail
Can be used without problems
Function and workability are fine, but
The part that suppresses Piston is Knurl by the genus Gold, so it scratches the inside of Piston.
If you are worried about it, you need to take measures such as putting Dustcloth in between.
View detail
It works perfectly fine.
I bought this because I was going to replace the Brake Pads myself and I wanted to clean the Piston.
I wasn't sure if I could rotate it properly because the part that grips the Piston is made of Gold, but no problem at all!
I was able to polish the Piston without much grip strength.
A must for anyone who cleans their own Brake Calipers or rubs out their Pistons!
View detail
Takes some getting used to?
I tried to replace Seal because I removed the Caliper, but it was on the way. "Oh, that's easy! . But I couldn't pull out the whole thing because I couldn't spread it out and lift it up. View detail
Don't fuck with the customers.
I would never buy from this company, even if they are the only Manufacturer in the world. The customer service is arrogant and offensive. The corporate attitude is to be expected.
It's a local business and I want it to go away.
I would definitely not recommend it to everyone considering it.
View detail
sufficient for one's needs
This is a necessity when you fail to rub out a Piston or overhaul a used Caliper with a Single Body.
Because the part that hits the inside of the piston is the iron of GizaGiza, there are some scratches on the surface of the piston, but it does not affect the performance of Piston, and if it can be pulled out by one shot, it is only a small scratch, so I think it is necessary and sufficient performance.
View detail
The problem before the product
I made a phone call, but the man who answered the phone was unpleasantly surprised by the unfriendly manner in which he spoke to me The employee training was inadequate and the quality of the products made by such a company is to be expected I expected it to be a local company, but I would never bring it up for purchase again View detail
I think the grip could be a little thicker
I bought it to try Caliper cleaning and used it immediately after receiving the product
There are many similar products, and if you look at the reviews, you'll often see that the inside of the Piston is damaged It's often reviewed, but so is this one
I used Vinyl Tape wrapped around it as appropriate
It is not so hard to turn the Piston, but it is still a little hard, so the Grip can be thin It was there and it was easy to get tired
It's a cheap part of the market if you think about it including points, so it's just right for those who are interested in it
View detail
Good cost performance
I bought this one to clean the Caliper myself for the first time!
It's not difficult to use for normal use, and I'm happy with the costumes
View detail
Mostly successful
A must for maintenance of your Brake Caliper
I used to use Snap Ring Pliers as a substitute, but the efficiency is still very different with it is
This is one of the cheapest PistonPliers on the market, but it's perfectly safe to use
I wish these tools could be used for different tasks;
View detail
High cost performance
Used for Brake repairs in Private Piston which was stuck and did not come off was turned and come off with these Pliers When the maintenance of Brake is done in the future, I think that I will use it positively I think that the person who does the maintenance by himself is indispensable Items View detail
You can use it enough
I used it for Piston which is a little fixed, but it worked well. Certainly, if you use it for strength, scratches inside Piston, but there is nothing to do with the performance of Brake, and it seems like I can not help it. Rather, at this price, I was able to maintain properly even with Piston, so it was good. However, because it is a bit delicate as a build, it may not be suitable for Piston where the size is sticking too much or Size is Large. View detail
Caliper piston Overhaul
Since Piston was also exchanged at the time of last Brake Pads exchange, we purchased this tool to try to reuse Piston for this Pad replacement.
(By the way, because last time I pulled Piston with Pliers, it was full of Wound and it was impossible to reuse very)
Even though Piston looks so dirty, I think that I can reuse it because it will be pretty much polished if I remove dirt.
With this tool it is very convenient and economical.
View detail