Reviews
Priced right and no damage to the adjuster.
Is a great tool to adjust the rear shock compared to using a screw driver and a hammer.It would have been extremely difficult and time consuming to preload springs without this tool.Recommend getting one to add to your collection.very handy tool, very good price.add;fits with exhaust clamps,triple tree nuts of old 50-250cc motorcycles View detail
Fits: HONDA PCX125, HONDA PCX125, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, YAMAHA Remote control jog, HONDA Lead 90, HONDA Lead 100, HONDA Lead 50, HONDA Lead 90, HONDA Lead 100, HONDA Lead 50
Price is higher, but Socket is more secure
I purchased this product to integrate KOSO's PowerKit into my ADV150. The quality and functionality are perfectly acceptable, but I wish the price was lower; it is not Wallet-friendly to spend over 2000 yen for a dedicated product that is used only for the clutch lock nut. I think that as long as the functionality is solid, the finish could be rougher.
GlassesType Wrench is cheaper, but the clutch lock nut is only about 5mm thick even though the diameter is large. So I decided to go with Socket because of its high price and peace of mind.
View detail
no problem
[How is it used?
To remove the center nut of the clutch
Was the one you received as per Image?
Yes
How was your experience with it?
It can be used with no problem, but you have to apply it firmly and straight.
Easily slanted
[Points to note]
Centrifugal for Clutch Band holder required
It said not to use Impact.
I used Impact when loosening lol.
It is only used when ClutchRose is used, so it is not likely to be used anymore.
View detail
I don't need it.
I could do without it.
I don't care if there is.
I can make adjustments without worrying about injury.
View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY R, HONDA MONKEY RT
Clutch disassembly essentials
These tools are essential for replacing the Clutch on the HondaHorizontal TypeEngine
I have seen some people making their own sockets by cutting off the sockets, but when you consider the price and quality, you need to buy a special tool to make it I think you should
The Material seems to rust easily, but..
View detail
Better than I expected
Space is limited with Back support and Chain Cover, and the OEM's Does Wrench deteriorate due to excessive use? I bought it because I started to do this, and again, the car-mounted tool was not strong enough and the tip was shaved off, so I had to use it We have changed this Wrench to an on-board tool
As per the Review, it seems to be fine for use in tight spaces
Try using it to change the Rear SuspensionPre-Set, make sure it's in the right position and use both hands It is easy to adjust the length of the car tool when working with the Done
Two suspension, like Mono Suspension both usable, easily and surely changed I think you can
The thickness of the tip is very thick and firm He chewed on it
It doesn't take much force to adjust the rear suspension to some extent with this wrench It seems to be covered
View detail
Fits: HONDA Forza., HONDA Forza., SUZUKI Sky Wave 250, HONDA phase, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350
It is recommended
Impact wrench mounted in no problem at all
3 KJJOG 's Clutch disassembly unavoidably purchased
When setting again etc etc. I think that there will be opportunities to use again Since it is better to have more tools than less
View detail
I feel relieved.
Purchase to do Initial adjustment of Rear suspension.
I purchased this because the size of Nut was unknown.
I can not rely on making it, but I could use it without problems.
Although it is used less frequently, it will be a problem if you do not have it, so do not lose it.
View detail
Adjustable Pin Wrench
The handle of the wrench is sturdy and has a nice rubber coating on it. The adjustable mechanism is nice and can be hand tightened sufficiently. The pins however are not very strong and a tightly jammed lock nut will cause the pins to bend. I have already bent the pins while opening a lock nut on a damper. However for light work it is quite adequate and price is cheap too Stronger pins would have gotten it a 5 star rating. View detail
Fits: HONDA NSR50, HONDA GORILLA, HONDA MONKEY
Can be used without problems
JA 07 Primary side of SuperCUB 110 (Centrifugation) Used for maintenance of Clutch. Pulley holder etc. are necessary to prevent co-rotation, but it was possible to use without problems.
It may be a story limited to SuperCUB 110, but somewhat sitting is bad, as long as the nail length is long. Although it does not matter if used with caution, it is hard to say that it is easy to use.
Because it is cheapest, if you touch the engine around the Honda car, I think you will not lose it if you buy it.
View detail
You can use
Ducati's Rear tire purchased for center nut removal.
Although it is a shape that Nut is not easily hung thinly, it holds firmly in this product.
View detail
Special tool
I was riding the car at the time of shipment for about half a year, but I wanted to adjust slightly and purchased it. It is hard to adjust the position slightly, but there is no problem.
I think that there are not many occasions to use, but these tools themselves have never been better than nothing.
View detail
Custom 中 ♪
I bought it for Rose to paint Front fork.
Without this tool, it was very handy as it could not be removed ♪
However, it would have been better if the part of possession was a little longer.
View detail
Although DUCATI HYPERMOTARD 796 was a cantilever Swing arm, in order to carry out the increase bundle of the big Nut of a Rear wheel, the 46-mm Socket of the DAYTONA was purchased.Although the use of the original product was a thing for clutch pulleys, it
Although DUCATI HYPERMOTARD 796 was a cantilever Swing arm, in order to carry out the increase bundle of the big Nut of a Rear wheel, the 46-mm Socket of the DAYTONA was purchased.Although the use of the original product was a thing for clutch pulleys, it has been satisfactorily used also for the Rear-axle Nut.
Although it was 46 mm and a huge Socket, since it was accurate, it was easy to impose a Torque and it has worked in comfort.It is just going to call this hit product made from a DAYTONA truly.
View detail
Fits: HONDA Forza., HONDA Forza., SUZUKI Sky Wave 250, HONDA phase, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350, HONDA fusion, HONDA Forza(MF10), HONDA Forza (MF08), HONDA Forza (MF06), HONDA Forza350
It is a big 41-mm Socket required to exchange the Rear sprocket of DUCATI HYPERMOTARD 796.In tool store, when it became this Size, there were many products offered for Impact wrenches, and the Socket thought that it became deep and was probably hard t
It is a big 41-mm Socket required to exchange the Rear sprocket of DUCATI HYPERMOTARD 796.In
tool store, when it became this Size, there were many products offered for Impact wrenches, and the Socket thought that it became deep and was probably hard to use, and purchased the Socket for the clutch pulleys of a DAYTONA.
Is it because it is a DAYTONA that structure is comparatively [ cheap ] solid?Even if actually used, it was easy to apply power and was an easy-to-use tool.
Although it was a seldom used tool, I thought that he bought a good thing.
View detail