Reviews
The problem before the product
I made a phone call, but the man who answered the phone was unpleasantly surprised by the unfriendly manner in which he spoke to me The employee training was inadequate and the quality of the products made by such a company is to be expected I expected it to be a local company, but I would never bring it up for purchase again View detail
Plastic Socket Strips at 40Nm Torque
Installing Matris Front Fork Cartridge kit F12RX when installing back on bike, socket stripped at 38Nm. @ Matris Please make a better socket harder plastic or Soft Jaw materials. View detail
Fits: HONDA CB900F, HONDA CBX1000, HONDA CB750F, HONDA CB1000C 83, HONDA CB1100F, HONDA CB900F, HONDA CB750F
You can't use the CB750F
It says to fit the CB750F, but it's not possible
I can't get Shim out due to insufficient amount of Lift on Valve
It's a waste of money
View detail
Too much accuracy
Accuracy is too bad, too much gap and rattle between the Bolts, and no matter how many times you adjust it, it's fixed at the right value I couldn't do it, so I had to use Glasses Wrench and Monkey Wrench to adjust it I did View detail
Fits: BMW K1600B, BMW K1600B, BMW K1600GT, BMW K1600GT, BMW K1600GTL, BMW K1600GTL, BMW R1200GS Adventure, BMW R1200GS Adventure, BMW R1200GS Adventure, BMW C600 Sport, BMW C650GT, BMW F750GS, BMW F800GS Adventure, BMW F800R, BMW F800R, BMW F800R, BMW F850GS, BMW F850GS Adventure, BMW K1200GT, BMW K1600GT
Necessity?
I bought it to change the front axle shaft,
It was not necessary at all. Crying
On the other side, to HexagonalNut of Axle division of Front LeftFork
If you have a matching Socket, you can exchange it without any turns.
On the other hand, if you do not have it, I think that it will be necessary, but in the amount of money?
It is much cheaper to buy Hexagon socket.
Although it may be good for those who need the accompanying Bit function, Bimmy
It is a product.
View detail
weak?
I chose DAYTONA as a reliable product if it's a product. Usability is good, balance adjustment is completed easily. However, since I changed the setting of carburetor about a month later, I set it again, and Gauge got 1 pc. It does not move at all, another 1pc. Even Gauge's swinging is slightly different from a normal needle.
Measurement etc etc. , Open Throttle with Valve open. I knew that it would be damaged if I performed the operation, so I was using it carefully enough and it has broken even though I did not do the wrong operation. I have two months to buy it yet. It probably is a product not covered by the warranty because there was nothing like a warranty card, but it has been broken too easily, you can not trust DAYTONA anymore.
Regrettable though it was a good product except durability.
View detail
Turning the stuck Jet, the tip deformed...
When trying to loosen the stuck Jet, the tip of the Driver easily deformed, and the Plating also peeled off.
"* Light TorqueSpec. For Carburetor it can not be used for. Although it is being done in the Instruction Manual, it is said that it will be broken so easily.
After all, Jet fixed it purchased a normal slotted screwdriver again at home center.
I think that this product can not be used very much for a long-term leaving carburetor that Jet species may be stuck.
View detail
after all - - -
I bought it for Main jet for Replacement and free shipping fee.
As I thought, I could not use it because of Space problem.
Plating also peels off at Torque of Jet
It was a place where Plating was entering in the room Float indoors.
View detail
I will slide to MAJESTYsClutch ★ Outer
Majestys155's
I could use it for Pulley ♪
But -
Clutch outer has
Anything!
This is due to R of Outer shape
I thought that if the convex of Holder was even 2 mm long
There is no dissatisfaction with the rigidity etc. of the product
View detail
Really for 4 mini?
I bought it for use under the waist of AB27's Engine, but I could not use it. Firmly does not fit in the hole of Flywheel. If you use it Thunder etc. There is no choice but to shave the Arm part. It was useless shopping. View detail
If an Oil reaches once whether an attached Tube is too thick, it cannot use being able to escape. The Tube thin after all a little was purchased, and it corresponded.
If an Oil reaches once whether an attached Tube is too thick, it cannot use being able to escape.
The Tube thin after all a little was purchased, and it corresponded.
View detail
a Maintenance of Cables -- it purchased. It is hard to use. Purchase examination of the thing of other company is carried out.
a Maintenance of Cables -- it purchased.
It is hard to use.
Purchase examination of the thing of
other company is carried out.
View detail
Although he thought that he would use for the cygnus X for 08 years and bought it, it hits and has a close game to the feather of a pulley. If it will arrange if the angle degree is attached to a slight degree, but it does by force, the angle of a loc
Although he thought that he would use for the cygnus X for 08 years and bought it, it hits and has a close game to the feather of a pulley.
If it will arrange if the angle degree is attached to a slight degree, but it does by force, the angle of a lock wrench is missing.
It is the price about mind!
View detail