Reviews
It is intended as an alternative to in-vehicle tools and for emergency use on the road.
The ZX-6R has an on-board tool storage compartment in the back of both the Tandem seat and the optional Single seat cover, but to use it, the storage bracket must be removed with a Hexagonal Wrench. It is very inconvenient though it is appreciated.
Since the servo motor of the exhaust device was removed to replace the external Slip-on Silencer, we decided to use the space to enhance our on-board tools and purchased this Compact with a minimum of tools.
For suspension setting, the Rear rebound damping force cannot be adjusted here, but I don't think this is a place that needs to be changed frequently in terms of usage. I have made a judgment on this.
Front can be used for each adjustment point.
I think it is better to prepare proper tools for daily maintenance, but I think it is better to separate it from emergency use on the road.
View detail
Buy with Ratchet wrench
Purchased for portable use. I think it is sufficient in terms of content and texture. View detail
Quantity:Set
I wanted to use it as a maintenance tool, [Contents] I bought it because the price was low. I am satisfied with the cost performance.
Switching the direction of rotation of Ratchet is difficult to do.
I thought it was a bit of a no-brainer for the cheap price.
View detail
![[YAMASHIRO] Special Tool DAP & DIE SET for YK-018 Motorcycle](https://img.webike-cdn.net/catalogue/images/55528/YK-018_TS.jpg)
We have all the Size you need.
I was worried about E-Value Tap dice set EV-20TD 20PCS, which is often sold at Home center in the same price range.
I bought this one because there are 2 Pitch size Tap and Dice each in M10 and M12.
The fact that it is also sold by Yamashiro is another reason for its selection.
I am a little hesitant about this type of tool unless it is a product sold in stores.
I immediately expanded the screw holes in the Fog Lamp from M5 to M6 and used it to clean the screw holes in the Large and Under Guard. Of course, Dice was also used to clean the screws.
View detail
I can do without it, but it would be useful.
Quantity of Hex wrench:I have a Set, but this Grip-type Hex wrench is useful when I want to apply Torque firmly while turning quickly.
With motorcycles, it is mainly used to remove the exterior and other parts. I mainly use it for maintenance on road motorcycles.
SIGNET's Wrench set is easy to buy because of its reasonable price. However, the Case is too large, so I would like to see some kind of device for it.
I Rose it and store it in my tool box.
View detail
Tools to carry when touring on forest roads
I always enjoy forest road touring on my beloved HUSQVARNA TE250.
I often have motorcycle troubles while touring, so it is very important to have the right tools with me.
We purchased this Tools Set because it seemed to be easy to work with in the mountains.
The decision was made based on the fact that there are 6mm and 7mm small sockets for HUSQVARNA, and that there is no need to change the size of the socket.
I have used it many times in the field, and it is very easy to handle and facilitates work.
One complaint I would make is that if the thickness were a little thinner, it would have been 100 points. But since it fits perfectly inside the Bag, it is not a problem again.
View detail
It is for Motorcycle use only and has a full range of Size
[How is it used?
I bought this to clean up the Screw Lock agent and to prepare the Yamas that were getting crushed when I removed and installed the Bolt for maintenance.
Bolts used in Motorcycle are often finer than standard bolts and will not fit in a standard tap dice.
This product is tailored specifically for Motorcycle and can be used with many Bolts used on Motorcycles.
Was the one you received as per Image?
[Contents] and Package were as shown in the image.
How was your experience with it?
As per its intended use, it functions well enough to clean screw yamas and prepare yamas.
Even if it is not cleaned in one round trip, it will be cleaned after repeated repetitions.
Closing the Nut after using it on both the Bolt and the Nut feels so good because it slips in just by hand. Cleaning it will allow you to tighten it with more correct Torque.
It can be said that it is cosmetically excellent to use this much for Bolt and Nut at this price.
[Points to note]
None
How did it compare to other products?
None
View detail
Surprisingly good.
I was thinking about a portable tool set from KTC, but it was too expensive considering how often I use it. I have not used it yet, but it seems to be able to do the bare minimum. It looks perfect for the price, and I think PinDrill is the way to go with at least OEM automotive tools. View detail
Convenient
Motorcycle maintenance requires the sizeQuantity:It is conveniently available as a Set.
The very compact Socket is convenient for working in tight spaces.
The quality of the product is not bad looking and I think it is very durable.
View detail
Good for first tools
Quantity to be able to work in one way.:The set is in Garage, so if this is in Garage, most things can be done.
It is very convenient because it is portable.
View detail
It is quite easy to use.
It is a little expensive, but quite easy to use.
The bite is different from Home center's cheap products.
I have been using it for about 2 years and even the Screws that seem to lick it don't lick it.
View detail
I'm buying again.
This is a re-purchase due to vehicle replacement.
Since the Trickle Charger I own is a Heller Socket.
Every time I buy a new car, I put a charging Plug on the Body.
I heard a rumor that the BMW G310GS I purchased this time had a weak Battery, so I decided to purchase and install it immediately.
Drill an 18mm diameter hole in the plastic cover under the Seat of the vehicle.
Body requires 4-5 cm of embedded Space.
Fuse is attached to the PlugBody and is connected directly to Battery.
View detail
I am purchasing again.
Since there is no power supply in the body of the BMW, the material under the seat can be used to charge the battery or to use an electric heating jacket and gloves.:Drilled and installed on PlasticCover.
I have replaced my long-standing Charger with HellerPlug, so whenever I change vehicles, I always purchase KIJIMA's Heller SocketPlugKit and install it in the vehicle body.
It is a little cheap, but it comes with Fuse and I am satisfied with the price.
View detail
Standard Penetrating Driver
It is Screwdriver Set of domestic MAJORBrandKTC.
”If you want a good Driver”, you should buy this one anyway.
The accuracy is also good for the price, and I don't think that the screw with the size will be damaged.
The square pattern is distinctive, but the design is quite logical as it does not roll easily and is easy to apply Torque.
Also Penetrating (except for the shortest one). The function of +α is substantial, and the usability is good.
”A good driver” is famous for PB and wera, but this product is the first Quantity before getting into it.:It is excellent as a Set.
This is because it has the beauty of being able to be used roughly as a ”Penetrating Driver” even after the tip has rounded off with use.
By the way, be careful because KTC's Logo is easy to peel off.
I think the best way to choose a driver is to buy this one and use it to the fullest, and then buy more high-end products like PB or wera as needed.
View detail
Tools Set to have one.
Up until now, I had been buying tools as I needed them, but as long as I had the tools, I could do the maintenance, but suddenly I needed a tool that I didn't have on hand, and I had to run to the home-centre.
Having a set of tools that you may need in advance not only saves you the trouble of having to do this, but it also allows you to combine a variety of handlebars to remove the same bolt and work efficiently in areas that are difficult to work in. Of course, the range of work that can be done has also expanded. As a result, even if I don't use some tools, I think it will pay off in the long run.
This Quantity:The Set includes a 12.7sq Large Socket and Handlebar, and is equipped with a full range of tools for removing and installing motorcycle and car wheels, so it's good to have one in your Garage for everyday use.
View detail
![[YAMASHIRO] Special Tool DAP & DIE SET For YK-018 Motorcycle](https://global.webike-cdn.net/uiu/impression/202110/19_1018981_616e653ab5d59.jpg)
First Tap&Dice set!
[How is it used?
I use it to maintain my motorcycle! I hadn't used it before to clean Bolt and Screw holes with Beauty before, but now I use it on the Main to clean Disc Bolt and other parts that were coated with Screw lock material when I tighten them again.
Also, when I'm doing maintenance and the Bolt is hard to get in, I do both the Bolt and Screw holes as a shuffle before installing.
Was the one you received as per Image?
The product itself was just as Image! The size is also for Motorcycle, so it has all the size you need, which is great!
How was your experience with it?
It seems not to be suitable for a little hard usage such as using GunGun or cutting a screw mountain in a new base material.
We recommend that you use it only for Main, for example, to correct the actual object.
[Points to note]
As I said a bit earlier, I don't think the Material itself of this product is that authentic.
Hard usage may cause damage, so it's better to use it carefully.
How did it compare to other products?
Honestly speaking, I thought to buy Astro Products at first, but I picked up this one because the size of Yamashiro's motorcycle line up was excellent.
[Opinions and requests to Manufacturer
It's a cheap product, so it's probably a bad idea, but the package is too lousy.
Please make the package more considerate of storage! If not, it will become RoseRose and squishy, and sometimes I feel sad when I open the toolbox!
View detail
Enough for the Sunday mechanic.
[How is it used?
When I bought the motorcycle, I wanted to do simple maintenance (oil and plug replacement, etc.) and I bought it.
Was the one you received as per Image?
I was worried about the inaccuracy and cheapness because of the reasonable price, but the workmanship was good and there was no particular problem in use.
How was your experience with it?
The size of the Socket is also wide, and Ratchet is also easy to use. In addition, because Case is also made of the genus Gold, there is a sense of luxury and I am satisfied.
[Points to note]
Because of the low price, there are concerns about durability and system problems, but there are no problems in performing simple maintenance.
How did it compare to other products?
I haven't used expensive high quality tools before, so it's hard to compare, but I think it's more reliable than using other very cheap tools.
Other items that would be helpful
Items to buy together
By purchasing Torx wrench together, you can divert the Socket and expand the range of maintenance.
View detail
Effective for narrow halls.
This socket wrench has a thin wall thickness, so it is effective for aluminum wheels with narrow holes. The wall thickness is thinner, but the strength is very high, so you can use it for Impact wrench with confidence.:You can set and use it. Quantity with the best size:Set and easy to use. View detail
Harley maintenance.
The Harley Owner has a Torx wrench which is essential for maintenance. [Contents] It is a good tool to have. Long type, good quality and easy to use. View detail
Useful for LED conversion
This is a useful tool set to replace Normal valve of Room lamp or Curtesy lamp with LED Bulb. The price is very reasonable when you think about the damage of the lens by forcibly removing it. View detail