Reviews
If you want to build a Tire with Tube, this is the one.
It is useful to pull out the Tube type Air Valve with ah-ha.
However, the Type Puller, which uses leverage, is better for use with Air Valve for Tubeless.
View detail
Grom JC92 can't be used as it is, but I was able to get the Piston Pin out with ease.
Piston Pin Puller, very useful.
I bought it because it was listed as having a compatible Piston Pin Size of 12mm to 25mm, but I need to take a moment to pull out the 12mm Piston Pin of the Grom JC92.
The construction of the product is very good, the grips are anodized, and it is not cheap.
Four types of attachments are included for pulling out the Piston Pin, which may be used on Large Motorcycle.
In the case of the Grom JC92 Piston, the smallest attachment has an outside diameter of more than 12mm, so the attachment is caught on the Piston perimeter and does not reach the Piston Pin.
So I pulled it out by biting a Spacer with an outside diameter of less than 12mm and about 5 cm, as shown in the photo.
The Curve on the Piston contact side of the Grip section was also fit to the Piston.
The Piston ring acted as a good buffer to prevent damage to the Piston, so there was no need to protect it with Dustclothetc.
View detail
So much benefit …
When performing the Tire exchange of the SUPER CUB, I thought of making the efficiency of the work, and the Tube Buy the Air Valve Puller to pull Air Valve
I actually used it, and while it was certainly easy to get the Air Valve through the holes in the Rim It was not that easy or fast, so it was a bit of a letdown
The separate attachment to Air Valve allows the wires to be rotated together when screwing in No construction But the Wire wasn't flexible enough, and once I used it, I got a breakage mark on it
View detail
I can not use it as it is
While removing the Oil seal of Susu Arm, I was working with Slotted screwdriver, but since some Seal did not come off, only Rubber part of Rip was torn, so I purchased it because I needed a special tool.
However, as you use it, the tip is a snake, so Seal will not catch it (Seal and Bearing were in close contact with each other) I could not remove Seal.
So using the sander to grind the tip of the tool made it easier to remove Seal.
If there is a gap in the back of Seal, I think that it can be used as it is, but in my case, processing of the tip was necessary.
View detail
If surely you are, it is convenient, but setting is troublesome and it seldom uses. With the Wire, dragging out forcibly is also likely to attach a crack to a Tube and it is uneasy at it. Since a phon only A-little patience carries o
If surely you are, it is convenient, but setting is troublesome and it seldom uses.
With the
Wire, dragging out forcibly is also likely to attach a crack to a Tube and it is uneasy at it.
Since a phon only A-little patience
carries out although surely a hand becomes painful and it is serious to take out the
Valve.
View detail
It was used at the time of engine decomposition of YAMAHA TW200, 236. If there isn't this, I think it is probably impossible to remove a rotor. It is not too bad, not too good, on the characteristic of the product. Although it seems a screw, there is like
It was used at the time of engine decomposition of YAMAHA TW200, 236. If there isn't this, I think it is probably impossible to remove a rotor. It is not too bad, not too good, on the characteristic of the product. Although it seems a screw, there is likely to be an intensity. View detail
Since pains were taken truly [ a hand hurts and ] to put a bulb portion into making an on-tire wear this time, it decided what kind of thing or to buy it. Although surely it becomes easy to put in indeed, and it comes simply up to the entrance of the
Since pains were taken truly [ a hand hurts and ] to put a bulb portion into making an on-tire wear this time, it decided what kind of thing or to buy it.
Although surely it becomes easy to put in indeed, and it comes simply up to the entrance of the bulb of a wheel, since a bulb does not pass at all however it may pull if it is as slanting as possible, this is a three stars in those of still the improvement by this with room.
Since it will be injured by a hand hitting a brake disc and a sprocket the moment the bulb passed if it pulls poor, special attention is required only there.
View detail
It is convenient if you are. However, since it has and the portion of a hand is bulky, it is unsuitable for a portable tool. It was *5, when it had and the miniaturization of the letter of a link could do the hand.
It is convenient if you are.
However, since it has and the portion of a hand is bulky, it is unsuitable for a portable tool.
It was *5, when it had and the miniaturization of the letter of a link could do the hand.
View detail
It purchased in order to form TT350 into 12V. Although attachment is needed for removing a magnet, pure attachment is phaseout, and it is ASE just for a moment. The bolt which is fixing the step after all was made to blow in between, and the magne
It purchased in order to form TT350 into 12V.
Although attachment is needed for removing a magnet, pure attachment is phaseout, and it is ASE just for a moment.
The bolt which is fixing the step after all was made to blow in between, and the magnet was removed.
Although a puller has a yamaha authentic positive ones and it has worked that there is nothing uneasy, it has turned at the handle which turns like looking.
If it is such a handle, the work it is more certain for there not to be may be able to be performed.
Other manufacturers also have a more firm product.
A general-purpose tool is under hunt on various vehicles.
View detail