Reviews
Double nut or Shift rod.
I bought it to use for double nut and shift rod.
It is 3mm, or about half the thickness of KTC's 6.5mm on hand.
The angle is 75°, which is not so common, so it is easy to hang even if Arm and Shift rod overlap.
Although there is a problem of strength, it would have been better if the jaws had been made a little smaller, as I don't think that high Torque will be applied to thin-lipped products.
View detail
Easy-to-use, handy tool
[How is it used?
Used for Motorcycle and car maintenance
How was your experience with it?
Solid for the price.
It is mirror plating with high accuracy and less rattling, so it can be used for bolt and other parts.
I don't know if it's almost impossible to put a scratch in it.
If I may say so, it is a little disappointing that there is no change in the hardness of the swing even when the Bolt of the swinging part is tightened.
How did it compare to other products?
It's not a swivel, but there's not that much difference in the Ratchet section compared to the KTC.
I feel a little rattled.
No problem for normal use.
[Points to note]
The hardness of the swing cannot be changed by tightening the Bolt on the swing section.
If the force is applied in a strange direction, it will break.
That's a little inconvenient.
Other than that, it is a handy tool that is easy to use.
View detail
Combination wrench for professionals
Ask any tool swamp dweller what”combination wrench they”d like to see, and the Stahlwille 14Series comes to mind. The Stahlwille 14Series is the one that comes to mind when you ask the residents of Tool Swamp what they think of”Combination wrench.
In terms of appearance, it is a higher-priced product with a pear finish, as opposed to Snap on and Nepros, which are higher-priced products with a mirror finish.
(As expected, it is cheaper than Snap on and Nepros.)
You will not see this in Home center or other places.
It is not as well-known as Snap on or Nepros, and its pear-shaped surface is not as glamorous.
However, it is a product that shines with its individuality backed up by its functionality, such as the feel of elasticity caused by the difference in materials, the difference in Spanner shape caused by the difference in design concept, and the Offset Glasses, which is rare for Combination wrench.
This is a good thing, because it gives a sense of being a professional.
(In fact, I hear it's accepted by Gen.)
Personally, in considering a replacement from KTC's StandardLine, I came to this product because I dislike the mirror finish.
I actually bought it and used it, and my impression is that it is
The bending feeling is definitely unique and uncomfortable until you get used to it.
Spanner is thicker, so you'll want a separate Thin Open Wrench.
Glasses are slightly different from ordinary combination wrench due to the combination of offset, neck angle, and thickness.
So, to be honest, it took some getting used to & it seemed to be a matter of taste.
I will use it as is for a while and if I like it, good, if not, I will sell it and replace it.
(High-end tools should be able to do this)
View detail
thin
I wanted something thin as a Spanner for tightening Nut and found this one and bought it.
Large, thin, and just right, and the price was reasonable.
View detail
Six KTC spanner set. There is only KTC and a thing is good.
Six KTC spanner set.
There is only KTC and a thing is good.
View detail
We have it all at Proxxon.
[How is it used?
Proxxon's 65 Points/Auto Mechanic Set 3/8 and wanted Wrench as well, so I bought this one from the same Brand.
How was your experience with it?
I like the slightly rough texture that is typical of Proxxon, and I like the way it feels in my hand.
As for the accuracy, I honestly don't know at my Level.
How did it compare to other products?
As mentioned above, I prefer it to many other plated, smooth, polished ones because it feels better to the touch.
The size and other information are clearly and conspicuously printed, as is typical of Proxxon, so they are easy to read.
[Points to note]
This Case is not very useful for regular use. I would like to find another tool case.
View detail
Like Caliper's Breather Valve.
I do have a glasses wrench, though.
The CombinationWrench is easy to use for Caliper air bleeding, etc. due to its handling and angle.
In addition, because the size is so small, there are many times when the 8mm bolt is needed in a secluded place, so I think it is more convenient to have a separate 8mm bolt.
View detail
easy to grasp
The width of the handle is rounded so that it does not hurt your hand when you exert yourself.
The pearl texture is my favorite Weight is Large, but I like it better because it doesn't show scratches.
As long as you like the way it looks, I think it is the highest Level Spanner as its reputation suggests.
View detail
The on-board tools are difficult to use.
The pin spanner of MC41 is not exclusive design, and the pin is shallow. The handlebar is also inconvenient.
The thinness and the length of the Handlebar are necessary factors because it is inserted between the Chain and the Swing Arm when in use, and this product meets those requirements.
The adjustment mechanism is that of a cheap MONKEY Wrench, and it is not smooth and has some rattle. However, the adjustment itself can be done normally, and there is no need to adjust the width as tightly as Bolt/Nut, so if the purpose is only to adjust the pre-road, it is completely sufficient. However, in such a limited use and frequency of use, the feeling of being expensive cannot be denied.
If you are going to use this product a lot, you might as well use Honda OEM Kowa Seiki, although it is more expensive. Therefore, this is a product of the halfway position.
View detail
Used in Restore of old car
[How is it used?
A little niche, but old cars. (SportsCUB) It was used to remove the key Cylinder of
How was your experience with it?
Unlike Rigid's Type, the claws open, making it difficult to work with.
The nails are not under tension and spin around.
It is necessary to devise a way to hook the nail firmly with the hand opposite to the handle and then turn it.
I would like to see the tension applied in the direction of closing with the spring.
I think it's worth the price.
[Points to note]
As I mentioned above, if you work with one hand, the nails are too shallow and will slip out.
How did it compare to other products?
If you want to be sure of your work, we recommend using an adjustable Spanner.
View detail
It's insanely light.
I was wondering if I could choose between DRC's Combo lever and this one for my first tire replacement. I purchased this product. The material is aluminum. There was no such thing as likely to break when using it because it seems to have been heat treated. However, because the thickness of the Lever tip is rather thick, when it is put into the gap of Tire, it is quite Large strange. This is the best solution for the purpose of reducing the number of items to carry. It may be the best solution for the purpose of reducing the number of personal items, but as a Tire Lever, it's a good idea. It might be a little less user friendly. I bought a Tire Lever with a thinner tip, like KTC or TSK, if you're going to replace the Tire at home. It's better. View detail
It works
I use it on my Monster1200R The Hook I was using to adjust the pre-road on my previous Panigale wasn't enough I was introduced to this product when I talked to my dealer It is View detail
Price suitable
Bought it for 4 wheels The purpose of this is to carry it instead of the in-car tools as I am worried about the car in case of an emergency is The Webike flexible ratchet I bought before was very useful, so I've been using it for four wheels I wanted one
One of the advantages is that the size is a little larger than the WebikeWrench set It's good for 4 wheels Also, I have several other SK11 products and they are a good cosmetic for DIY use
On the cons, the surface is beautiful with plating, but it is easy to get fingerprints and oil on it Also, I knew it, but the number of GEAR is less than WebikeWrench The usability of a small space is going to make a difference
The price is low and it's originally for emergency use, so that's OK, but it's usually a good idea for motorcycle maintenance For use, I recommend the WebikeWrench set
View detail
To the tool Mania
Simultaneous purchase when Rear suspension is exchanged for Other Company Product.
There is no cheapness, the making is solid and the feeling of use is very good.
There is no use scene after setting Rear suspension (My situation) , I did not like cheesy tools, so I selected this product.
View detail
Steering stem nutWrench
Stem bearing purchased for replacement, because the service manual tightened Torque was stated, it was found that Torque wrench could be used somehow and found this product.
How to use Torque wrench to Spanner to 90-degrees and tighten it can apply the prescribed Torque.
The product of DAYTONA chose this product also because it is used as Torque wrench impossible and Honda OEM.
Usability was satisfied as I expected but satisfied Stem Nut It was too light as I closed it with Torque, so I adjusted it several times by hand tightening.
Cost performance is a bit bad so we have four stars.
View detail
Inexpensive and necessary and sufficient
Clean Mirror processing and necessary enough accuracy - It is durable but inexpensive but attractive! I also love other Size. This time, because I often use Size, I purchase additional items. View detail
since it is an Adjustment Type -- -- -- although it was worried, it is solid and can fully use.Is there only what the maker specifies as the pure tool?
since it is an Adjustment Type -- -- -- although it was worried, it is solid and can fully use.Is there only what the maker specifies as the pure tool? View detail
Since it was wasteful that it became impossible to use when it changed when it was a stationary type authentic positive in a Manufacturer, the adjustment type here was used.Compared with a Manufacturer authentic positive one, it was cheap, and since it us
Since it was wasteful that it became impossible to use when it changed when it was a stationary type authentic positive in a Manufacturer, the adjustment type here was used.Compared with a Manufacturer authentic positive one, it was cheap, and since it used ordinarily, you could choose here. View detail
Since it was the worried Manufacturer, it purchases to a trial. It can use with a sufficient feel and a Plating is also likely to be durable. I merely think that an overall length is a little long.
Since it was the worried Manufacturer, it purchases to a trial. It can use with a sufficient feel and a Plating is also likely to be durable. I merely think that an overall length is a little long. View detail
[Webike Monitor] It is firmly fastened by the Torque wrench. A plug mouth is 3/8. I think that it is found useful since it can use also for Initial adjustment of a Rear suspension.
[Webike Monitor] It is firmly fastened by the
Torque wrench.
A plug mouth is 3/8.
I think that it is found useful since it can use also for Initial adjustment of a Rear suspension.
View detail