Reviews
Hammer for punching
[How is it used?
I was looking for a large hammer because I had only a small hammer to smash during maintenance, and a large hammer is also a small hammer.
Anyway, I bought it because it was big and looked sturdy.
Was the one you received as per Image?
It has a reasonably Limit weight to support with one hand.
It was quite ideal.
How was your experience with it?
It is useful in many ways, such as tapping the Shaft and Shock driver.
I have been handling it roughly, but so far there has been no damage.
The grip of the handle is also good so it does not fly away.
[Points to note]
It has a reasonable Size feel to it, so it is difficult to store.
Also, since considerable force is applied to the parts, there is a possibility that the parts may be destroyed if the work is done in a frustrated manner.
How did it compare to other products?
The power is different than the chubby Hammer I had on hand.
【Review】
This tool is unnecessary if you just want to maintain your Motorcycle normally.
It can be used to pull out rusted or stuck shafts on immobile or abandoned vehicles.
View detail
I don't want to put a scratch in it.
It is used to remove parts that are hard to install or adhered to in places where you do not want to scratch.
Size:#1, 1 PondLength, HeadLargeThickness and weight seem to be the most convenient.
The cost is easy, and the head can be exchanged, so if you have 1pc. you can use it in various ways.
View detail
Convenient
One Side is a Plastic Hammer and the opposite is an Iron Hammer, so it is convenient to wear them in different ways.
The quality is very good and the Grip is easy to hold.
View detail
Combination hammer！
I have used it for many years.
I would recommend the Combination of the Gold and Plastic departments to be Iifusuri after all.
The handle is also easy to grip and apply force. The Grip also works well.
I use it in many situations, not just Motorcycle, and I use it for Peg typing.
View detail
From heavy-duty maintenance work to camping
I bought this because I have been doing a lot of hard work such as removing Axle Shaft of Motorcycle.
The grip part is a normal rubber, but it is easy to grip.
It seems to be useful also for the Peg beating of Campingetc.
View detail
It is convenient to have one.
It is useful for something with a conconnection of hard-to-get-into Parts.
It's a combination, so it's heavy, and the resin part is a hard Material, which is helpful to replace if it's damaged.
View detail
Easy to hold Grip
The RubberPlastic hammer can be used effectively on the cylinder head and aluminum oil pan where it cannot be hit hard. View detail
It's convenient in two roles.
One side is a plastic hammer and the other side is a steel hammer, so it's very convenient to use it with a single piece of equipment. View detail
Grip replacement
I love it when I change my Grip!
Put Towel on the Grip to prevent Wound from going to the Grip
I'm hammering away at it!
It is easy to hold and use
View detail
Trusted KTC
I bought the tools because I have decided to use Proxxon Proxxon and KTC Basically, I use it to beat the shaft when I change tires The price is very high because of KTC, but I will use it for a long time because it seems to be easy to use and strong I expect to be able to use it Most of all, it's a fun thing to own View detail
Just right
It is Hammer which is indispensable when one wants to knock one such as inserting and inserting Shaft and Tire's Bead at the end at exactly good Large weight. View detail
KTC's "UD 7 - 10" It is a comparison with.
Unless it is used only for Motorcycle and car work and does not do Large construction work, it is also released from KTC "UD 7 - 10" The usability is better for.
Because, this "PH 68 - 344" Because the sharp point of the nail is used only to suppress the protrusion after driving the nail. I thought that I could use it once for board Gold, but it was too heavy and it was difficult to moderate power, after all I gave up.
on the other hand "UD 7 - 10" Is a combination with Plastic hammer, and there are also scenes that are used in car and motorcycle work in Large. Although there is not much turn in light work, it is very convenient in scenes to dismantle.
View detail
Convenient to attach something
The ordinary Hammer was in the Set tool, but since Praghan was not there, it was purchased additionally. It is useful when you striking gently instead of tapping with hands. weight - Both Large and Kimi are good, Large enough to enter the tool box is good View detail
It is charmed by the price and purchases. - It is touch with thickness and exactly sufficient die length in orthodox form. Since R is attached to the end of the handle, it is difficult to come out somewhat. - The design of the character of GEN
It is charmed by the price and purchases.
- It is touch with thickness and exactly sufficient die length in orthodox form.
Since R is attached to the end of the handle, it is difficult to come out somewhat.
- The design of the character of GENUINE HICKORY became a simple considerably.
Whose pre- design was better --
- A center of gravity is a 1 or 5-cm place from a portion with a thick root of a handle to the right.
As it is, I think that it is a light handle.
- Coating of the varnish ? feels that it is coarse.
Although I think that there are a hit and a blank BOTETSU and the attached portion are 2~3 places in some places.,
It does not appreciate and is satisfactory.
View detail
User-friendliness is quite good although it is ball pin hammer 12OZ (fiberglass handle)!! It is convenient that a hand does not become painful or is not numbed even if it uses, since it is [ a grip part ] soft. Since a size also has more than one,
User-friendliness is quite good although it is ball pin hammer 12OZ (fiberglass handle)!!
It is convenient that a hand does not become painful or is not numbed even if it uses, since it is [ a grip part ] soft.
Since a size also has more than one, I also regard that it can unite with a use as it being one of the charm.
View detail