Reviews
Good accuracy
I had been using cheap valves and Type radio pliers, but I decided to go with a proper Manufacturer's product, so I chose KTC's Radio pliers.
Even with a strong grip, there is no gap at the tip, and the precision is as expected.
View detail
With this.
Minimum required tools.
If you are going to modify the electrical components yourself, at the very least, this should be enough to make the Large sturdy.
There are cheaper ones, but they are difficult to use or lack Size….
If you look above, there is no Drill, so for now, here is the Recommendation.
View detail
There are three mouths.
Snap rings are often used to hold down the Kick Arm axis of a moped scooter.
LargeIn the past, I used radio pliers and pick tools as substitutes. It was still inconvenient, though it was usable for the time being, and it took a lot of time and effort to remove the Ring by holding it down and almost scratching the Aluminum case.
My senior recommended me to buy a dedicated pliers and I used it for many years, but the tip of the mouth broke off and I could no longer use it. Once you know the taste of dedicated tools, you can't stand the inconvenience. The last time I used this type, I had to replace the mouth, but the target was not always the same snap ring, and I didn't want to go through the trouble of finding a different mouth each time, so this time I bought SK11's one type with three mouths. It takes up more space in the tool box, but in terms of total area, it is no different from the mouth-changing type. It can't be used in deep places, but I don't plan to use it for anything other than my Dio, so that's not a problem. It is a tool that I don't use very often, but the price is not as high as before. If I need another type, I can buy it again.
After all, Snap ring is not something to work with a substitute tool. We also felt that just using this tool would save time.
View detail
Savior of the Rusted Screw!
I had Neji-saurus, but I bought additional KNIPEX!
And comparison
Strength to add Screw with the mouth.
The Neji-saurus has a longitudinal groove cut into the end of the pliers.
The size is not adjustable, so there is a limit to the diameter that can be held in the mouth. Moreover, since the size cannot be adjusted, the ability to grip is limited by the diameter of the screw.:Pair (for Left and Right) It will be….
KNIPEX can widen the mouth with a slip joint, so almost all
You can grab it at the best Point to Screw.
This difference is anyway Large tight!
Ability to grab on to something other than the mouth
KNIPEX is diamond-shaped and holds three points, so it can be gripped firmly.
In addition, the slip joint can be adjusted to suit the object to be gripped!
The Neji-saurus engages all the way when closed, so it is good for gripping thin objects, but difficult to grip objects with a Large diameter or thicker objects….
Conclusion
You should definitely buy KNIPEX from the beginning!
When I bought Neji-saurus, they didn't sell KNIPEX Slip joint pliers yet... Crying
View detail
A clear difference in grasping ability!
I've been using Pliers for a few hundred dollars from Home center,
Since it is a gripping tool that is used rather often, go to KNIPEX of trust.
Prices are also high enough to betray your trust, though (sweat)
I think you can tell from the pictures,
The machining accuracy of the tool is levechi ！！！！
Oh my, how easy it is to use (laughs).
I've left it in place, but the home center tool is not in use.
The basics are gone!
Good tools are the ones you use most often!
It's seriously inspiring!
View detail
Need to buy two of them, for Shaft and for Hole!
I used to use a very inexpensive for-hole and for-shaft combination from Asphalt.
Lots of rattles and poor workability.
So I bought a hole, for Shaft, from top quality KNIPEX anyway!
In the case of Asphalt, the parts you remove can fly away due to rattling and be lost.
But if you align the holes and for shafts independently, you can get the same results.
Well, all of those failures will be eliminated!
I want to use good tools and do good maintenance comfortably and without waste anyway.
I guess so!
It's a tool that PRO just raves about!
Well, the price is also PRO price….
View detail
There is a reason why expensive tools are expensive!
Only for tools that are rarely used,
I have been using a tool made by Asphalt that can be used for both for Shaft and for Hole.
I used to use it, but maintenance is part of my hobby.
We are replacing them with better tools little by little!
What's best is the feeling that when you grab it, it won't let go!
As for the as-fat, for the amount that both can be used with the earlier replacement.
There was a lot of rattling, and when I took it off, I had to skip it and look for parts.
Sometimes I have to do it …. This is a waste of time and effort.
KNIPEX has no such problems so far!
If you consider maintenance as a hobby, buy it!
View detail
I've been using A Fat for years, but the accuracy of Crimping is totally different!
I bought it at Home center when I started messing around with Motorcycle.
A Fat Electric PliersQuantity:Set
I've been using this for many years, but I'm not sure if it's possible to make a Bullet Terminal during the Wiring process or not.
I'm getting frequent, so I got excited and went to KNIPEX.
A Fatty is more multifunctional and has a Scissors section that cuts off wiring.
What's easy to use is easy to use,
In terms of Crimping, once you pinch it.
After deforming the Bullet terminal to some extent, it is like this Crimp.
KNIPEX is hard to cut because Wiring cut is in the middle.
But when Crimping, just hold it without thinking and you can Crimp on Beauty!
The difference is really huge!
It's an emotional Level.
So, A Fat is in storage (laughs).
View detail
Similar to Pliers.
It is the same as Pliers and is well made and easy to apply force.
It also operates smoothly, so it is not a cheap product.
It is useful for detailed work, etc.
I have some Rust recently, but would like to maintain and use it.
View detail
Used for many years
It is easy to grip and apply force, so it is Firmly attached.
It is quite useful because it is sometimes used in various scenes unexpectedly.
Accuracy is good and no Wobble.
View detail
Overhaul of Master Cylinder
It is very useful when doing overhaul of the brake master cylinder.
It is a Copy product of HondaOEM tool, but it is durable and easy to use.
I use it a lot for my work, so the price is not expensive and well worth it.
View detail
Safety wire wrap/cutter
I gave a place in my toolbox.It's definitely a luxury item, but I think it's worth it. They make setup very easy and work exactly as you hope. The quality and feel won't surprise you, but they're good for the price. The cutter isn't great and for some reason it doesn't work close enough to the pivot point which is kind of annoying Handles safety wire like a champ, could use cutting edge run all the way to joint, there is a about a 1/2" where there is no cutter but that is nit-picking. Used it on three sets of grips with no issues.cut through the wire fine without damaging themselves, and I expect them to hold up for a long time View detail
![Stamp Pin Set [for Stamp: 125: 11]](https://img.webike-cdn.net/catalogue/13962/4962485091132_1_TS.jpg)
Rounded tips, scratch resistant! Good quality!
It is used to attach Stickers.
Conclusion. Unquestionably a good product." It is! Unlike Tweezers with rounded and pointed tips.
Sticker is scratch resistant! It's hard to explain, but it's easy to grab things with a perfect grip.
The price is very reasonable … I would buy this product again even if it cost 3 times as much!
View detail
Purchased to install Uotani.
Pliers are fine, but a dedicated tool is still safer. View detail
Powerful pincers!
Water pump pliers are a necessity for playing with motorcycles.
Ordinary pliers have a weak bite, but water pump pliers have great bite and are easy to turn and grip.
View detail
![Reverse Operation Pin Set [Reverse Operation (Small): 120: 8]](https://img.webike-cdn.net/catalogue/13962/4962485091156_1_TS.jpg)
Even though they look similar....
Tweezers can be found in a hundred different places.
However, there is still a difference in finish and usability that does not show up in appearance.
I put it side by side with a hundred items for comparison, but the BALI on the Edge is carefully removed and finished so as not to scratch the object to be sandwiched.
In addition, parts with this (Wiringetc.) When used on a motorcycle, for example, it requires a certain degree of strength, unlike, for example, holding down parts of an electrical product.
The one from a hundred-yen store was not strong enough and did not hold when needed. The products of a different manufacturer from ANEX are also weak in holding power, and this product was the easiest to use.
Therefore, I recommend this product when purchasing reverse-acting Tweezers.
View detail
good
Used to replace Clutch on CUB90.
Lock nut with room to spare because it grips Firmly.
It was loosened.
However, the sides of the clutch should be degreased with Parts cleaner.
I think it will improve the bite.
Might it slip with Oil on it?
I used Holder on Clutch after degreasing.
View detail
To remove Snap ring
Analog Oil Temperature Gauge that was previously installed on a GB250 CLUBMAN is being repaired because oil is getting into the window surface of the Oil Temperature Meter and the oil temperature cannot be determined.
I was thinking.
There is a snap ring on the window surface of the Oil Temperature Meter, which must first be removed before moving on to the next task.
I tried various ways to remove the Snap ring but could not get it off, so I ended up buying Snap Ring Pliers.
It is not a tool that I use very often, but I think it would come in handy if I had it.
I have tried to Rose the Oil Temperature Meter, but could not fix the problem.
View detail
sturdy
It is solid for the price. I bought this because the one I had before was cheap and the tip was bent.
This one shows no sign of bending at all, so I feel safe using it.
View detail
When it comes to water pump pliers, this is it!
This is hard to tell without actually holding it in your hand, but nothing feels as comfortable as this.
The make, grips, and everything else is different from cheap water pump pliers.
Even so, it is not that extremely expensive.
It is a gem that you should definitely have one of these.
Recommendation
View detail