Reviews
1 pc to save as many Screws as possible.
[How is it used?
When I was working on my motorcycle at home, there were some bolts that could not be removed by the driver, and I had to destroy the screws.
I could have chosen any manufacturer's product, but I chose DAYTONA, which handles a lot of motorcycle products.
Was the one you received as per Image?
It was just like the picture.
Slightly Large? Standard size.
How was your experience with it?
There are some places where it exits as I thought it would when I used it and some places where it does not.
The object must be restrained so that the force does not escape, and it does not seem to be suitable for sideways Screwetc. on a car body, for example.
I was able to remove the screws in areas where the force did not escape, so I will try again by placing them against a wall or something in areas where I could not remove them this time.
[Points to note]
Quantity the object so that the force does not escape as described above.:Set is required.
How did it compare to other products?
I wonder if it is an OEM or the same factory that produces it, since it is identical to the Shock driver of A0tro PROducts. I wonder if it is OEM or the same production factory.
【Review】
Shock drivers are available from various manufacturers, but I think they are relatively inexpensive and of good quality.
There are many types of Bits, so it can be used for Screws in various places.
View detail
Compact
Compact and useful for use in tight spaces.
It is small and cannot apply much force, but it is easy to use when tightening a little and replacing the tip.
I like that the price is not that high.
View detail
I thought I wouldn't have to do without it, but I finally got my hands on it.
[How is it used?
ESTRELLA's filler cap is a type with a minus cutout similar to the Timing Hole Plug, but it is usually opened with a slotted screwdriver with a large slot, so I have not touched the coin driver. I have not touched the coin driver.
One day, I tried to open the filler cap with a slotted screwdriver to put in oil, but I got stuck... I didn't want to do it, but it was an emergency and I tried to open it with a coin, but the coin lost out.
I finally reached out to Coin Driver because I knew I could not turn my back on them.
Was the one you received as per Image?
Although the shape itself was the same as the product image, the actual product seemed smaller (compact) than I had expected.
This was not a problem, as the compact design is more convenient to keep in a tool box.
How was your experience with it?
It was the first time for me to use the Coin driver, and I was a little worried if it would fit because there was no description of size and so on, but I was able to use it on ESTRELLA and Filler cap without any problem. I was able to open it safely.
[Points to note]
Even though it is a Coin driver, I think it is indeed useless if the Size is not right.
It is a good idea to check the Size of the part to be used before purchasing.
How did it compare to other products?
It definitely works better than Coin.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Small and comfortable to hold
The Size is easy to grip.
It is also easy to apply force there.
View detail
Rather than turning Screw.
Purchased because I wanted a Minus in Small size.
Minus of such a size is often used for doing things by sticking it into a gap rather than as a driver when servicing.
View detail
Sk11 tool good.
It's a good value for the money and well made, useful in tight places where drivers and such can't get in. I have used other sk11 tools and they are very good and reliable.
Thank you very much.
View detail
Inexpensive, but normally usable.
It's cheap Level sold at a hundred and one. I bought it imagining that it would be a "good" product, but I was betrayed, but in a good way!
I use it not only for Motorcycle but also for maintenance of Glasses and Watches!
View detail
I got it off!
CB1300 (sc40) I was having a hard time removing the sticking PlugPin on the front caliper of the
I bought the Shock driver because I thought it would be impossible to remove it with lubricant alone, so I thought the Shock driver would work. I thought it would be impossible to remove it with just lubricant, so I bought a shock driver. I guess having a tool reduces the trouble by half.
View detail
KITACO JET Driver
About quality and texture There are all the tools for setting up pe24 About the feeling of use However, my hands hurt when I tried to use the + driver with my bare hands without wearing gloves Products to buy together all in one product Difficulty of installation It's good to use for setting Cost performance and comparison with other products The price of this product is good and the portability is really good, so I recommend it! About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I needed a simple tool to carry around, but it's a well-made product and it's reasonable price As I mentioned above, my hands can hurt with my bare hands, so I recommend wearing gloves and setting them View detail
Efficiency of tinkering with old cars
I have been tinkering with my car for over 30 years. Sometimes I have a stuck Screw that I can hit with the Hammer without having to switch to the Impact Driver. It is very convenient. View detail
KTC Slotted screwdriver
It felt good in my grip and I was able to apply force well.
I was able to successfully remove the screw that I could not remove using a cheap tool.
View detail
Screw Catch DV No.470
I haven't used the Screw catch yet, but it seems to work well in tight places without dropping the Screw. However, it may be a little difficult to push down by hand in tight places. View detail
It is a useful tool when one is in a tool box. Quality is also a problem pear if it is KTC!!
It is a useful tool when one is in a tool box.
Quality is also a problem pear if it is KTC!!
View detail
Although (+)(-) substitution type of the other company was used, since it had exhausted, it replaced in passing. Although only (+) was mainly used, since it was cheap, (-) was arranged. Is the direction of the stationary type solid too? It is
Although (+)(-) substitution type of the other company was used, since it had exhausted, it replaced in passing.
Although only (+) was mainly used, since it was cheap, (-) was arranged.
Is the direction of the stationary type solid too?
It is not a penetration driver although I think that there are those [ no ] who strike this size.
View detail
I've been using it for years.
The handle is large, so it is not suitable for light turning.
The precision is outstanding, and I guess KTC is made in Japan.
The part to turn with force is also secure, and it is hard to use other cheap tools.
View detail
Minus to match Plus.
Since I already had a Phillips screwdriver, I wanted a slotted screwdriver as well.
Like Plus, the handle is large, so it is not suitable for light turning, but in the case of Minus, it is used when applying a lot of force, so it is not MinusPoint.
View detail
Not quite as nice as a megadora, but grippier
The 'woody' handle is useful as it is less slippy than other types and resists oil on the hands very well. Its a good screwdriver but I think I prefer the Megadora range if i am honest as they seem more robust and of course impacta version is alwys needed at some point. All in all a good JIS driver for the money. View detail
For removal of Air cleanerBox.
It was a Plus screw on the Air cleanerBox, so I bought it to turn there.
The Grip is also shaped for easy grasping and use.
I thought it might be a little expensive compared to another Manufacturer, such as Home center.
We chose KTC because it is a reliable tool that can be used for several years.
Minus is also a Quantity:I thought it was a Set and bought it together.
View detail
I was able to use it conveniently with my 4mini below the waist Custom.
The Screw which fixes the StatorBase of your beloved car DAX is Size3 in Plus.
I think it is impossible for a normal Driver to loosen this one.
This time, I was able to remove it safely by using this product and Hammer which I bought separately.
Size3 is one sizeLarger than the regular Plus screw.
I don't think you can have an Exactly Driver very often.
If it is this product, it can be used as a normal driver if it is not beaten with Hammer.
I think it is a convenient product that has no loss to have 1 pc because it can be used.
View detail
A definite classic.
The cross section of the shaft is round because it is not designed for rough work, and therefore it slides and turns very well even if it is supported by hand.
This ball-shaped grip is easy to turn quickly and is a definite tool for light, twirling work.
Personally, I would recommend the ANEX electrician's tool if you want to do everything in one tool, even a little rough work.
ANEX shaft (Hexagonal cross section) It can be used to turn the tool on and off, which is helpful when you have a tougher screw than the ShockDriver.
Both of them are performance as a driver. (Bite, durability, etc.) is sufficient.
The VetuCell is the Grip shape that many people prefer, so many people will prefer this one.
I think it's better to use the one you like when you actually touch it.
View detail