Reviews
In times of emergency
It has been used for 20 years, but recently it is a Driver whose turn has become less frequent. Easily loosening Screw is easy to use Vessel's Grip is Ball type, so here is fixed and active in Vessel when it seems to be licking. Penetrating Driver Overwhelming Large's Screw by turning it while shocking. View detail
Sturdy
Although I purchased it in 20 years, I can still use it on the active side. Penetrating Driver also sometimes used pretty rough usage, but it is Tough that can not be cheap. View detail
I think it's good.
I was using Vessel's Wooden HandlebarDriver, but as the number has decreased and it began to slip, I replaced it..
Compared to Wooden Handlebar, Rubber's wartsboot Grip is not slippery, it is easy to put power in a square.
The tip does not exactly engage with Screw and it does not rise.
Stand up Driver and support your butt with your index finger Round and round When you turn it also fingers are likely to hang around the square corners.
Length of shaft is a bit short, but it is easy to put force and can also apply Wrench with Penetrating formula.
It seems to be heavier than the drivers of other companies, but I think that it does not matter so much if it is the frequency of personal motorcycle maintenance.
View detail
It is a shame driver
Driver uses WERA, PB, Vessel, TONE, SIGNET and so on.
I purchased and used TPMD 18 of this Driver 8 book KTC and used it as a comment.
- Because it is rectangular, power comes in, but it is unsuitable for continuous turning and heavy.
- The coloring of + and - is easy to see, Design is also good.
- Is it due to chemical adhesion? "KTC" Label got peeled off (Crying).
** Label should be printed or engraved (Secondary disaster prevention).
I tried using a high Driver, but I say it is ownership desire or quit with self-satisfaction.
After all, I repurchased KTP's LTPMD 126 that I used before.
For me this is the most inexpensive and Recommendation.
Although the number is different, it is 2000 yen cheap even for the same KTC!
View detail
I increased the type because I bought it before.
PB 206S - 3 Ball Point Hexagonal Bar Screwdriver I bought earlier was easy to use
I bought 206S-4 and 206S-5.
View detail
Manufacturer goods, quality is different to drift.
When holding the part firmly and turning Screw
Torque will be applied steadily and Screw will be knocked
Worry is drastically reduced.
When saying things, you can hit the bottom with Hammer
It is made of Gold genus as possible.
Very easy to use Cost performance
It is an excellent product.
View detail
I increased the type because I bought it before.
PB 206S - 3 Ball Point Hexagonal Bar Screwdriver I bought earlier was easy to use
I bought 206S-4 and 206S-5.
View detail
Automatic for Vehicle wanted it to be shorter (number 3)
Since the Bar End of our Motorcycle is tightened with Screw lock + strong Torque, teeth do not stand in the usual Driver, but you can remove it with this Driver.
Also, so there is no place to use No. 3 so much (number 3) If you have one item - - - I thought, please do not do too long for automatic for Vehicle.
Recent automobiles are made Small as they make it Small, so there is Screw in the back place, even if there are places where parts can be seen - - - Depending on Manufacturer, there are things that are not easy to maintain.
In our Motorcycle, there may not be necessary for Motorcycle as there are only places used only for Screw of Cover of Air Filter, Screw of Battery terminal, Bar End.
However, the impression of Japan Manufacturer was received as truly as making the product itself.
View detail
Driver of count 1 has few scenes that can be used
Since I purchased Penetrating type Driver of the same series, I tried to purchase this product with the first count by trying to arrange it in one place, but now I can not find a place to use in our Motorcycle.
So I tried using it for purposes other than Motorcycle, but again I choose Screw for automatic for Vehicle.
Although I can turn it without licking firmly, I can not turn Screw which can be turned by No. 1 Driver which is not Automatic for Vehicle of other Manufacturer.
If you put it in a tool box it may be useful time someday because it is a Penetrating expression, but I think that it is not necessary to forcibly buy a person who is not necessary so much.
(Since it is heavier than Non-Penetrating one, it will increase the weight of the tool box... )
View detail
We do not recommend regularly, but where we need power ○
Not to mention Japan Manufacturer, but more than anything, price is cheap for Specifications.
Although it is an impression of using it, I do not recommend regularly because Driver itself is heavy.
I think that there are individual differences, but the handle is not cylindrical and it is square "Hold firmly and put your strength" It is very easy to use for minutes, but it is so tightened so strongly (removal) It is hard to use for the part that you do not need.
Also, as mentioned earlier, the Driver itself is heavy, so to handle lightly it needs to be strong so it gets tired when used continuously.
It is a bit disappointing that it was heavier than other Manufacturer's Penetrating formula, but it seems that the strength is so high.
View detail
Cross Driver
Since I was doing Events at a neighborhood shop, I went to see it, I just bought it.
Events contents are Grip part and Blade part are six colors (Red - Blue - Yellow color - Black - Green - Purple), press-fitted on the spot, I also purchased two unintentionally.
View detail
Fun Bolt removal, installation
I purchased it as if I could easily turn Bolt when removing safety parts of Motorcycle. I was glad I could buy it with the aimed effect. Good texture. Cost performance is also good. Large Kimono is there as it is carrying Socket. View detail
Multifunctional!
Home 1 pc for tool box, 1 pc for Motorcycle on-board tool, Total Quantity : 2 pc owned, but several Attachments are convenient according to ScrewBolt! It is heavy, but it is heavy but if you get used to it you do not mind. Rather, I think that rather than having several Drivers carry around umbrellas. I think the price is cheap for KTC.
View detail
Easy to use
I bought it for disassembly assembly of Carburetor.
I bought to shorten the maintenance time as it is a Ball point. After all it is safe for PB products. I would like a Lineup of the Ball point Hexagonal Bar Driver which is a little longer if possible.
View detail
Difficult to use, intriguing
I can not get power. I have used it because there are occasions when it is inconvenient, but it is hard to use.
There is a dent that Ratchet fits or there is room to consider as a tool to devise a slip prevention shape or a tool.
When using, I use Grip 's good gloves to keep the power from slipping. Recommendation on this usage.
View detail
It's fine.
I always use KTC at home, MAC at shop, but I wanted another and bought it.
I was bought for the first time PB but it is quite nice.
Screw will loosen as you cling to it.
It is also nice to have a hexagon at the base.
Although it is good to stick to Manufacturer, since I think that each Manufacturer specialty field is there, I have recently bought and tried various other Manufacturer specializing in specialty fields.
View detail
Exactly to Jet
(1) I am using it for Carburetor's low Jet exchange.
(2) I can join Exetly in the groove of Jet, I can turn Jet without play, I will not hurt Jet.
(3) Part of the Black at the tip will be peeled relatively quickly. I use it only a few times a year, but I got a little peeled off in about 3 years.
(4) Grip smells a little when it is wet or when it gets wet with rain.
View detail
For carburetor
In order to disassemble and clean the carburetor, I purchased it because I needed a slotted screwdriver with the same size as the axis.
I looked for various things, but surprisingly I did not sell a slotted screwdriver with the same size as the axis.
As a result of looking at Net, I decided to buy a PB driver famous for Driver so that I can use it anyway if I buy anything.
The color of the part of Grip is beautiful and I personally like it, but as you saw on Net, it is quite dangerous. Will it disappear after a while? It is unknown whether it is like this forever.
Although durability is still unknown, well, if an amateur uses it to tamper the carburetor it will probably be the last one.
View detail
Ratchet driver
I purchased it because I can trust in JAPAN.
Basically I use it at work.
As everyone seems to have a heavy feeling
I feel heavy with having only Driver,
I do not feel much weight when using it.
As a result, it is regrettable that Bit of other Manufacturer can not be used.
View detail
-Driver's male
【What made you decide the purchase?】 Speaking of the male of -Driver PB!
【How was it actually used?】 I bought it for 2 types of electric worker examinations. (eh?) It is easy to bend the nail of OutletPlate when the tip is parallel.
[Is there anything I was disappointed about?] I have not been beating it yet, will not it be lost if I hit it?
【Hope for Manufacturer - Please tell me if you have any improvements】 Grip's unique Smell ,,,
【Have you compared items?】 About Nepros?
View detail