Reviews
DAYTONA Impact screwdriver
DAYTONA Impact Screwdriver This tool is indispensable for working on the engine. More than once I thought to do without it, and the result was a knocked down edge on the bolts and a replacement. Therefore, I ordered an impact screwdriver. I am very satisfied with the quality, everything is good. A separate plus is a metal case. This tool is essential for working on the engine. More than once I thought to do without it, and the result was a knocked down edge on the bolts and a replacement. Therefore and ordered an impact screwdriver. I am very satisfied with the quality, everything is good. A separate plus is the metal case. View detail
I should have bought Koch from the beginning (#2)
Common L-shaped Quantities:I had been using a set, but I happened to know at work that there was a Driver type Hexagonal Wrench, so I bought a 5mm one of the same series.
The L-shaped type cannot be used to work around electrical components with complicated wiring, which can cause licking of screws and damage to the wiring.
But with this driver type, all these problems were solved in one shot.
The Large size of the pattern is also different from 5mm and is thinner.
View detail
I should have bought this one from the beginning.
Common L-shaped Quantities:I had been using a set, but I happened to know at work that there was a Driver type Hexagonal Wrench, so I bought a 4mm one of the same series.
It is extremely easy to use and almost eliminates the risk of dropping tools and damaging the motorcycle.
View detail
Sk11 tool good.
It's a good value for the money and well made, useful in tight places where drivers and such can't get in. I have used other sk11 tools and they are very good and reliable.
Thank you very much.
View detail
Anyway, it fits in my hand!
They're comfortable in your hand, easy to turn! And cheap! I've been using GunGun heavily and it will probably last me a lifetime. View detail
The smallest and lightest Merit is the Large Merit.
I bought this to play with the carburetor part on the go. To be honest, it is cheaply made and hard to turn.
The small size and light weight make it easy to carry around.
If possible, I would have liked to have a part to attach a Key Holder.
View detail
Inexpensive, but normally usable.
It's cheap Level sold at a hundred and one. I bought it imagining that it would be a "good" product, but I was betrayed, but in a good way!
I use it not only for Motorcycle but also for maintenance of Glasses and Watches!
View detail
honestly speaking, it's subtle
I thought it was easy to use with Pencil type and purchased it for electric inspection, but the system is not very good. View detail
I got it off!
CB1300 (sc40) I was having a hard time removing the sticking PlugPin on the front caliper of the
I bought the Shock driver because I thought it would be impossible to remove it with lubricant alone, so I thought the Shock driver would work. I thought it would be impossible to remove it with just lubricant, so I bought a shock driver. I guess having a tool reduces the trouble by half.
View detail
Accuracy and strength!
Of course, as Precision Driver, the precision and strength of the tip is outstanding.
When I made Slit machining Spark plugs for Others, I also use Precision Driver for pushing and drilling holes to get BALI when I am about to Penetrating in Slit machining.
Really great tip strength!
View detail
Are non-Motorcycle uses more frequent?
So far "Large" When "Inside Although I had a Driver for the "Small" was purchased because he did not have one.
[How is it used?
Motorcycle in general, and all other products that use +Screw in general, but where and how often it can be used. "Inside The Driver is much less than the Driver in the "Mere Old Man". However, it is just fit to the +Screw that stops the back cover of the mobile training game that was popular more than 20 years ago.
Was the one you received as per Image?
The one I received looked as high quality as the picture and had a thin coating of rust-proof Oil on the tip.
How was your experience with it?
It seems to fit very well in the hand, and the grip is very firm, so it will be easy to put on and off the Screw.
However, since the grips are too tight, it is better to use a little more force when using it on a part that should not be tightened too much.
[Points to note]
Select and use the appropriate +Driver number for the appropriate +Screw.
How did it compare to other products?
until now "Inside I've been using only the +Driver of the "Small" This is the first time for me to use the type of Driver in the "1" series, but the accuracy, ease of use, and fit feel are good.
Also, my personal impression is that the Plus and Minus Screwdriver Sets are sold separately, but perhaps
I don't think I'll be able to use all of them, so as far as drivers are concerned, I only buy what I need from Single Item sellers.
I think it would be a good idea to do so.
View detail
This is the most universal driver with a large size.
It became the number one Driver that I often use for both Motorcycle and products that use +Screw, and I bought it because the Vessel +Driver that I had at home was worn out.
[How is it used?
It can be used for all Motorcycle and other products that use +Screw, and since it is the most frequently used number driver, it can be used in a wide range of locations.
Was the one you received as per Image?
The one I received looked as high quality as the picture and had a thin coating of rust-proof Oil on the tip.
How was your experience with it?
It seems to fit very well in the hand, and the grip is very firm, so it will be easy to put on and off the Screw.
However, since the grips are too tight, it is better to use a little more force when using it on a part that should not be tightened too much.
[Points to note]
Select and use the appropriate +Driver number for the appropriate +Screw.
How did it compare to other products?
Compared to the worn Vessel +Driver, the accuracy, ease of use, and fit are still improved.
Also, my personal impression is that the Plus and Minus Screwdriver Sets are sold separately, but perhaps
I don't think I'll be able to use all of them, so as far as drivers are concerned, I only buy what I need from Single Item sellers.
I think it would be a good idea to do so.
View detail
Compatible with Handlebar Weightetc. screws
Purchased because I had an inaccurate +Driver at home and had almost licked the Screw when servicing it.
[How is it used?
Screws with Handlebar Weight installed and screws of OEM Exhaust Cover of MONKEY50 are now supported.
Was the one you received as per Image?
The one I received looked as high quality as the picture and had a thin coating of rust-proof Oil on the tip.
How was your experience with it?
It seems to fit very well in the hand, and the grip is very firm, so it will be easy to put on and off the Screw.
However, since the grips are too tight, it is better to use a little more force when using it on a part that should not be tightened too much.
[Points to note]
Be careful not to over-tighten when using this product in areas where tightening Torque is not very high.
How did it compare to other products?
Compared to T-drivers made by other manufacturers, the accuracy, ease of use, and fit are far superior.
Also, my personal impression is that the Plus and Minus Screwdriver Sets are sold separately, but perhaps
I don't think I'll be able to use all of them, so as far as drivers are concerned, I only buy what I need from Single Item sellers.
I think it would be a good idea to do so.
View detail
KITACO JET Driver
About quality and texture There are all the tools for setting up pe24 About the feeling of use However, my hands hurt when I tried to use the + driver with my bare hands without wearing gloves Products to buy together all in one product Difficulty of installation It's good to use for setting Cost performance and comparison with other products The price of this product is good and the portability is really good, so I recommend it! About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I needed a simple tool to carry around, but it's a well-made product and it's reasonable price As I mentioned above, my hands can hurt with my bare hands, so I recommend wearing gloves and setting them View detail
Must have for every tool box
I have stripped screw heads multiple times over the years and did not know a tool like this existed. After I saw this being demonstrated in one of the youtube Videos, I decided to purchase one. Well the day finally came that I needed to use this and without any drama I was able to remove a stubborn screw that otherwise would have ended up stripped.Must have for powersports! It saves stripping out philips screws and small bolts that tend to seize on off-road equipment.This is a must have for working on Japanese bikes. The bits fit the screws on my bikes better than a standard philips and the impact function makes getting stuck screws removed super easy.It comes with the box, there are bits in it. View detail
Efficiency of tinkering with old cars
I have been tinkering with my car for over 30 years. Sometimes I have a stuck Screw that I can hit with the Hammer without having to switch to the Impact Driver. It is very convenient. View detail
It is not necessary to have it, but it is convenient to have it.
At this price, you won't feel like you're missing out if you have one.
The thicker grips make it easy to hold and apply force, and it is definitely easier to turn than using a 500-yen coin.
View detail
Graduation from Screw Mountain Licktaro
I don't even remember how many times I have done DIY maintenance for the best of my intentions, and how many times I licked Screws and ran to the Motorcycle shop in tears.
I had been thinking about buying one for a long time and finally bought one when I decided to replace my Brake Disc.
I wondered if I, who had licked countless screws in my life, would be able to remove the screw lock on the Brake Disc. I put everything into this tool.
I hit the Bit with the Hammer with all my might. At first I didn't know how much force to apply, but when it loosened up, the response was sure, and I was impressed, not Largereally exaggerated. I really wish I had bought it earlier. I was able to remove all Bolts without taking a single lick.
The only thing is that I have never used a Shock driver before, so I am embarrassed if my perception is wrong, but the part where the Hammer strikes is not flat but lightly curved, so it sometimes slid and hit my hand. I wonder if this is to prevent too much force from being transmitted.
I don't mind too much because it is not difficult to use, but I wonder why the place to tap is not flat.
All in all, I am satisfied, considering the yet-to-be-seen Screw that I would have destroyed without it.
View detail
Unfortunately, it did not come off.
[How is it used?
The front coverBolt on the Scooter has taken a licking.
I bought it.
Was the one you received as per Image?
They did a Screw cut that bites firmly into the Plus screw that has been licked.
How was your experience with it?
As a result, the Rusty and sticking Screws were not scared.
[Points to note]
It says to remove it by tapping it with Hammer, but be careful because tapping sometimes changes the direction of rotation.
View detail
Surprisingly, this is good.
VESSEL is useful because of its modest tip accuracy and inexpensive price.
Of course, there are some areas that are inferior to PB and Vera.
but there is nothing like it in terms of cosmetics.
It is Largei that it is inexpensive and does not hurt the pocketbook even if it is used in a messy way.
It's nice to have an expensive one, but also nice to have a quality one in this price range for everyday use.
View detail