Reviews
I will never buy from them again.
I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail
I tried to exchange Seals.
I tried to replace the oil seal on the crankshaft of my LEAD125.
I couldn't replace it because the bracket was pulled out of the grip and the end of the pin was deformed.
I don't know if the strength is too weak or if only a smaller seal can be pulled out.
View detail
Poor.
I bought it because I thought it was cheap and good that the tip could be replaced.
The downside of the tip replacement is that it often hits too many areas and cannot reach tight spots.
The C-ring is so hard that the tip is useless because it is wobbly.
At any rate, I can't RECOMMENDATION because there are so many irritating POINTS.
We managed to finish the work, but it was a Level we never wanted to use again.
Tools are Large stamps.
View detail
I am Garbage.
I was expecting it to be dedicated to Bullet Type Terminal, but this is Garbage.
The Wiring and Clothing sections can only be Crimped at the same time in one time, so the positioning is very severe.
Even so, the Crimp section is so thick that it is almost impossible to see where the Wiring is located.
Even when it was finally done, the crimped shape was flat and uneven.
A Caulking Tool, which costs less than 1,000 yen, will give a cleaner and more reliable finish.
I used it a few times the day it arrived and it went to the Garbage bin.
View detail
Only OEM parts fit Honda vehicles!
The thing is nice, but only the OEM PlugRatchet fits Honda Motorcycles! View detail
It doesn't work …
It said that the Plug would not fall off with Magnet, but the magnetic force was too weak and it did not stick at all, and the rubber inside was too weak to hold the Flag at all. View detail
Fits: HONDA CB1300SUPER BOLD'OR, HONDA CB1300 SUPER FOUR SP, HONDA CB1300 SUPER BOLDOL SP, YAMAHA MT03, YAMAHA MT-07, YAMAHA MT-25, KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400 (2014-), KAWASAKI NINJA400 (2014-), KAWASAKI VERSYS-X 250, KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA NC750X, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR
What's up, DAYTONA!
I used their Filter wrench for 10 years on my XL1200C SPORTSTER 1200. It was very accurate and easy to use.
When replacing the filter on the NC750X, we had no hesitation in purchasing Wrench from the company.
Although it fits Firmly with no problem in accuracy, it slips paca-paca-paca when Torque is applied and cannot be loosened.
The steel plate is not rigid enough and seems to open its mouth.
I had no choice but to purchase a KTC casting separately. This one is a one-shot OK!
When I installed their ReplaceOil Filter later, I tried to loosen it with this Wrench to test it, but it still crackled & hellip;.
I know you are a longtime seller and there are a lot of users, but are you Large sturdy?
View detail
Driven Sprocket Replacement
I purchased this to replace a Driven Sprocket, but could not use it because the Nut seemed to lick when a strong load was applied.
I bought another socket (TONE hexagonal) at Home center and replaced it. The price was about the same.
I thought that a hexagonal shape would be more suitable than a dodecagonal shape because of the torque applied, but Webike did not have a deep hexagonal shape, so I had no choice but to purchase one. I used it once and will never use it again.
View detail
Does it serve the purpose of a dedicated tool?
I bought this to use on an overhaul of an old brake master as described in the product description. It is true that I can grab the C-ring at the back, but as soon as I grab it and try to pull it out, the tip part broke off.
Since it was used for only a few minutes, we wonder about its Cost performance as well.
I wasted my time and Gold, but I still decided to buy a special tool from ToolManufacturer.
View detail
It is not an article which can be used as a tool at all. It bought and lost!
It is not an article which can be used as a tool at all.
It bought and lost!
View detail
Please never buy it. Because something does not suit the air zipper 22.
Please never buy it.
Because something does not suit the air zipper 22.
View detail
Not compatible with RnineT
Does not fit OEMOil Filter for RnineT (OEM Product No. 11427673541).
The shape is different to begin with.
I would like to see a proper description of compatible car models.
Garbage no longer
View detail
No Case in the listed photo
This is the first time I've seen a single body on the market. View detail
The GEAR broke immediately.
It is very useful for attaching and removing the bolt in tight places, but the ratchet gear on the closing side was damaged after a few times of use because it is easy to apply excessive force. View detail
It's broken
I used it as soon as it arrived and it broke… View detail
I couldn't turn it on the GSX-S1000F.
In a small Space, you can use Filter. It did not. If you can hold it firmly with your hand, it will turn. I'm a little disappointed with my purchase. View detail
I pulled the wire.
When I installed the product on the Air Valve, I grabbed the handle and pulled it, the wire came off from the Air Valve installation part and it became useless.
It broke after the first use, so it was a waste of money.
View detail
You will receive a different shape from the picture
The shape is completely different from the one in the picture, so it's useless It's the same name, but with the model change, it's changed to something completely different I'm not sure if this is a good idea or not, but it's not a bad idea If you buy this, you will lose money View detail
You will receive a different shape from the picture
Actually, the shape is completely different from the one in the photo, so it's not useful It has the same name but seems to have changed to something completely different with the Model change The shape of the blade is also completely different, so it would be a loss to use it View detail
Wrong image
Product name is The PROXXON Proxxon 1/4 Torque Socket Bit And the product that arrived The PROXXON Proxxon 1/4 Torque Socket Bit It was
If you just look here, it's fine, but the product image is different No matter how you look at it, the image looks like a hexagonal product I wanted a hexagonal Bit
I was at fault for looking at the product image and reading the name of the product and ordering it, but I don't think this is too much
I noticed this when I received it and contacted them on April 23 to return and exchange it
We are currently waiting for We-Big's reply
They said it would be dealt with gradually, but it's taking a little longer to deal with the situation, even though it's after a long period of GW I think it's like
If you plan to purchase, please compare the product name and image carefully before placing your order I will
View detail